Quick Start Wizard steps, Identification | Siemens LR 460 specification

Quick Start Wizard steps

Notes:

•The Quick Start settings are not independent parameters. The settings are inter- related, and changes only apply when you click Transfer at the end of step 4.

•Do not use the Quick Start Wizard to modify individual parameters: see instead Parameter Reference on page 43.

•Click BACK to return and revise settings, or Cancel to exit the Quick Start.

•The layout of the dialog boxes shown may vary according to the resolution setting for your computer monitor.

Open the menu Device – Quick Start, and follow steps 1 to 4.

Quick

Start

Step 1 – Identification

Click NEXT to accept default values. (Description, Message, and Last config fields can be left blank.)

Quick Start

7ML19985JM01

SITRANS LR 460 – INSTRUCTION MANUAL

Page 31

Page 37

Image 37

Siemens LR 460 instruction manual Quick Start Wizard steps, Identification

Contents

Sitrans Contact Smpi Technical Publications at the following address Table of Contents Quick Start Wizard via the handheld programmer Table of Cotents AIFB1 AIFB2 Iii Appendix F Hart Information Structure Safety marking symbols Safety NotesDirect Current 7ML19985JM01 FCC and IC Conformity Canadian Installations only Industry Canada IC rules Support ManualApplication Examples Abbreviations and Identifications Short Long Form Description Units Cont’d Approvals and Certificates ProgrammingSystem Implementation Power SpecificationsSpecifications Performance Interface Mechanical Programmer infrared keypad1 Process EnvironmentalCommunication Approvals Standard configuration Dimensions Installation InstallationMounting Location Nozzle design Key considerationsNozzle location Device orientation Polarization Reference Point Installation in vessel with obstructionsPolarization Reference Point Holding the electronics enclosure firmly Easy Aimer Installation Air Consumption Air Purging System OptionalFlow rate versus applied pressure Pipe Flange Thick Bolt Hole No. Slotted Flange Dimensions see above Optional Dust Cap Installation Connecting Sitrans LR Wiring Connecting Hart Typical PLC/mA configuration with Hart Hart wiringAC version DC version Power Demands Profibus wiringBus Termination AC version DC version From Connecting Sitrans LR 460 on page 19, step For use and assembly, refer to the main instructions Hazardous area installationsProduct Nameplate Reference European Atex Directive 94/9/EC, Annex II, 1/0/6 Thermal Data for 7ML5426 Series Device Permitted ambientDirective 94/9/EC Annex II, clause 61241 -17 in Europe 7ML19985JM01 Quick Start RUN mode displayActivating Sitrans LR Quick Start Programming Sitrans LR Press Mode to return to RUN mode Quick Start Quick Start Wizard via the handheld programmerLanguage Application Type Options Units Operation typesHigh Calibration Point Values Quick Start Wizard via Simatic PDM Configuring a new deviceDevice Description DD Identification Quick Start Wizard steps Application type Range Setup Summary Level application example Quick Start Setting Description Auto False Echo Suppression Operating Sitrans LR 460 via Simatic PDM Rev .0, SP2 FeaturesFunctions in Simatic PDM Echo profile saving and viewing Trend Diagram Level Trend over TimeOpen the menu View Trend to see the level trend over tme Open the menu Device TVT Shaper Manual TVT Shaper Online Display Accessing Functions in PDMDisplay Configuring a new device Changing parameter settings via Simatic PDMDevice Description DD Reset Parameters accessed via pull-down menusConfiguration Flag Reset Hart only Calibrating LR 460 via PDM Simulate AO Analog Output Digital/Analog TrimSimulation Simulate Analog Input to AIFB1 or AIFB2 Parameter menus Parameter ReferencePull-down menus via Simatic PDM Device menus View menus Language Options Quick Start WizardOperation Slow Identification ConfigurationOperation Unit Open the menu Device Set Address Description To perform a Reset via the handheld programmerProgram Mer Device HandheldProgrammer Statistics Input Sensor Calibration Low Calibration Pt. default 30.000 mCalibration Sensor Units Low Level Point default High Calibration Pt. default 0.350 mHigh Level Point default Level Offset default Measuring Limits Detailed SetupValues Options Ters RelatedParameters Parame Echo detection position ParameEcho Sampling Window Range Window UsedNear Range Far Range To use Auto False Echo Suppression via Simatic PDM TVT Auto False Echo Suppression setupOpen the menu Device Auto False Echo Suppression Auto TVT Auto False Echo Suppression Example after Auto False Echo Suppression Display before Auto False Echo Suppression TVT Hover Level Manual TVT Shaper ModeManual TVT shaper To change a breakpoint via PDM Values Range 0.0000 to 99999 m / min Altered byAltered by Related Echo Information OutputAIFB1 Batch Phase Target Mode Profibus PA onlyUnit Filter Time Constant Process Value Scale Upper Limit AlarmUpper Value Output Scale Limit Hysteresis Fail-safe Mode Profibus PA onlyMin Out Max Out MA Output AIFB2See AIFB1 the parameters for AIFB2 are identical MA OUT value = x x 16 mA + 4 y Man Value Related parame Certificates and Approvals Relay ConfigurationDevice Certification Related parame Remaining Device Lifetime Maintenance settingsRemaining Sensor Lifetime Calibration Interval Service Interval Parameters Appendix a Technical Reference Related Response LOE Timer Fill RatePrinciples of Operation Measurement Response Profile monitoring via Simatic PDM Echo ProcessingEcho selection Time Varying Threshold TVT Auto False-Echo Suppression False EchoesBeam angle at -3dB reference Technical LOE Timer Fail-safe ModeEcho confidence Near Range Blanking Fail-safe value Temperature on the LCD secondary display Maximum Process Temperature Chart Troubleshooting LR Symptom Possible cause Remedy Appendix B TroubleshootingTroubleshooting Set Far Range to a lower value Reads empty Reads vessel bottom RegionFluctuates Is normal Troubleshooting LR 460 cont’d Symptom Possible cause Remedy General Fault Codes/PROFIBUS PA Extended Diagnostics Outside its temperature Perform serviceSame Check configuration for Has expired Eeprom damaged Local Siemens Representative Local Siemens By a memory error RepresentativeEeprom corrupt For the network Module Representative Local Siemens Device has been lost RepresentativeUnable to collect profile Local Siemens Representative Local Siemens Distance measurement Representative Maintenance Appendix C MaintenanceUnit Repair and Excluded Liability Program Mode Display RUN mode startup displayLCD Display Local Interface Handheld programmer Hand-held programmer key functions in RUN modeProgramming via the handheld programmer Key Function Hand-held programmer key functions in Edit mode Hand-held programmer key functions in Navigation modeIndividual Parameter Reset Key Name When Navigation Mode Simatic Process Device Manager PDM Hart Device Description DDHart modem interface for Simatic PDM Hart Communications Sitrans LR 460 does not support Burst Mode Burst ModeHart Version Hart Communication Parameter Profile structure Hart Block Model for recording and processing measured valuesLevel Transducer Block LTB F-90 Analog Input Function Blocks AIFB1 and AIFB2 Description of the blocks Appendix G Remote operation via Configuration toolDevice Description Remote Operation PA GSD file Setting the Profibus address ConfigurationConfiguring a new device procedure Calibration via Simatic PDM Configuring Profibus PA with an S7-300/ 400 PLC Cyclic versus Acyclic Data Appendix H Communication viaCyclic Data Communication PA Status Codes for Good Quality Status ByteCodes for Bad Quality H-96 Acyclic Diagnostics DiagnosticsDiagnosis reply applies only to cyclic masters Status Codes for Uncertain Quality Byte Bit Description Indication Class Acyclic Data Transmission= set H-98 Profibus Level Device Design Appendix J Profibus PA Profile StructureProfile structure PA Level Transducer Block function groups See parameter diagram onProfie structure PA How the Level Transducer Block works Sensor Reference Point Analog Input Function Blocks 1 Electronics temperatureHow the AIFBs work Setting Description Output value J-104 Software rev Software DD Rev Date ChangesInitial release K-106 Sorftware rev Glossary Glossary Glossary Stilling-well see stillpipe Glossary Index Index Quick Start Wizard Reform Echo Reliable echo indicator 85 repairView Status byte LCD menu structure Echo SEL LCD menus LCD menu charts LCD menu charts 7ml19985JM01