Oil in Water Analyzer | Teledyne 6600 instruction

Oil in Water Analyzer

OPERATING INSTRUCTIONS

Model 6600

Oil in Water Analyzer

DANGER

HIGHLYTOXICANDORFLAMMABLELIQUIDSORGASESMAYBEPRESENTINTHISMONITORINGSYSTEM.

PERSONAL PROTECTIVE EQUIPMENT MAY BE REQUIRED WHEN SERVICING THIS SYSTEM.

HAZARDOUS VOLTAGES EXIST ON CERTAIN COMPONENTS INTERNALLY WHICH MAY PERSIST FOR A TIME EVEN AFTER THE POWER IS TURNED OFF AND DISCONNECTED.

ONLY AUTHORIZED PERSONNEL SHOULD CONDUCT MAINTENANCE AND/OR SERVICING. BEFORE CONDUCTINGANYMAINTENANCEORSERVICINGCONSULTWITHAUTHORIZEDSUPERVISOR/MANAGER.

P/N M71055 12/22/99 ECO # 99-0000

Teledyne Analytical Instruments

Image 1

Teledyne 6600 manual Oil in Water Analyzer, Teledyne Analytical Instruments

Contents

Teledyne Analytical Instruments Oil in Water Analyzer Copyright 1999 Teledyne Analytical Instruments Model Iii Table of Contents Model Teledyne Analytical Instruments Part I Control Section Model Ii Part InstallationOperation Part I MaintenanceAppendix Model 6600 Oil in Water Analyzer Iv Part Oil in Water Analyzer Part I Control Section Overview Operator Interface Main Features of the AnalyzerIntroduction Model ESCAPE/ENTER Switch Model 6600 Controls, Indicators, and Connectors Model 6600 Interface Panel Control Section Interface Panel Electrical Connections Unpacking the Control/Analysis Unit 115VAC Installation Model Analog Output Connections Examples 10.4 Range Voltage Current mA Alarm Relays Part Data Carrier Detect RS-232 Sig RS-232 Pin Purpose Parameter Setting Command Description Testing the System Part Introduction Using the ControlsOil in Water Analyzer Operation Mode/Function Selection Operation Model Hierarchy of System Functions and Subfunctions System Function Setting up an AUTO-CAL EnteringthePassword Password Protection Installing or Changing the Password Logging Out System Self-Diagnostic Test Checking Linearity with Algorithm Operation Model Model Screen Setting 90% Response time Seconds Digital Filter Setup Set Ultra Sonic Homogenizer on Homogenizer Function Setup Hold/Track Setup Analog 4-20mA Output Calibartion Operation Model Calibration/Hold Timer Setup Manual control of filter and solenoids Algorithm Application Model Outcal Anlz Algorithmapplcation Model Outcal Anlz Zero and Span Functions Zero Cal Auto Mode Zeroing Manual Mode Zeroing Zero Offset Calibration Detector Failure Spanning How the offset value is selected Manual Mode Spanning Auto Mode SpanningOil in Water Analyzer Operation Span Cal Alarms Function Oil in Water Analyzer Operation Range Select Function Auto Screen Precautions Illustrates these schemes graphically Analyze Function Programming Oil in Water Analyzer Operation Set Range Screen Curve Algorithm Screen Auto Mode Linearization Ppm SO2 InputØ Part I Control Section Maintenance Fuse Replacement Maintenance Model 6600 Oil in Water Analyzer System Self Diagnostic TestPower Analog Preamp Major Internal ComponentsDetector Side View Open Door Part II Analysis Unit Part II Analysis Section Control/Analysis Unit Ii Part Part II Iv Part Oil in Water Analyzer Operational Theory Method of Analysis Operational Theory Model Optical Bench Photometer Amplifier Automatic Zero System Zero drift may occur in the following cases System Description Source Module Photometer Detector Module Sample Cell Sample Systems Unpacking the Analyzer Installing and Connecting the AnalyzerOil in Water Analyzer Part II Analysis Unit User Connections Signal and Alarm Output Connections Installation Model Electrical Power ConnectionsCompressed Air Supply Pipe Connections Calibration Calibration Fluids Method One Calibration Oil in Water Analyzer Maintenance Routine MaintenanceSystem Visual Check and Response Procedure Automatic operation and routine operational duties Routine Maintenance Maintenance ModelSuggested Preventive Maintenance Schedule Power Supply Test Points Service Procedures and Adjustments ElectronicsSetup of the Signal Processing Front-End Amplifiers Oscilloscope Display of the I to E Converter Output Part Inverting Amplifier Setup of the Logarithmic Amplifier Interface Board Terminals Strip Battery-Powered Oscilloscope Synchronization Point Part Oil in Water Analyzer Maintenance Part Part III Oil in Water Part III Model 6620 Oil in Water Analyzer Table of Contents Part III Model 6620 Oil in Water Analyzer Oil in Water Part Introduction Optical Bench Method of AnalysisPhotometer Amplifier Part Model Part III Automatic Zero System From B71046-0 or customer’s piping schematic Oil in Water Piping Diagram B71046 Part Part III System Description Source Module PhotometerSample Cell Control/Analysis Unit Detector ModulePart III Teledyne Analytical Instruments Sampling System Sample Water Preconditioning System Electrical Connections Pressurized Inlet Sample Delivery Zero Water Preconditioning System Homogenizing Ultra clean process applications for leaks into the like Automatic Sample Cell Cleaning System Entering the zero offset Recorder Requirement Signal Outputs Amplifier PCB Process Alarm SystemAuto Zero Circuit Detector Fail Check Detector signal Signal Failure Alarm Installation Signal and Alarm Output Connections Electrical Power ConnectionsUser Connections Compressed Air Supply Safe Vent Drainage Sample Delivery System Electronics Check Installation Check Sample Delivery Check Electrical CheckPreparation for Calibration Manual Sample Introduction Required Calibration Equipment Acquisition of Representative Sample Water Acquisition of Representative Oil Sample Oscilloscope Display of the I to E Converter Output Background Signal Level Determination Part III Part Model Zero Fluid Preparation Calibration with Prepared SampleSpan Fluid Preparation Calibration Setup of Internal Span Flag Calibration SpanFilter Calibration by Correlation with Laboratory AnalysisSample System Part III Calibration of the ultrasonic homogenizer Correlation HomogenizerTuning Automatic Operation and Routine Operational Duties Electronics Set-up for Automatic Operation Routine Maintenance System Visual Check and Response Procedure Monthly or 6 weeks maximum Daily Set up of the Signal Processing Front End Amplifiers Service Procedures and Adjustments Set Up of the I to E Converter Integrated Reference and Measuring Signals Set Up of the Logarithmic AmplifierInverting Amplifier Sample Cell Maintenance Zero Filter Replacement Sample System Maintenance 316 Zero Filter Cleaning Procedure Phototube Replacement Lamp Replacement Lamp Refuses to Light Troubleshooting Section Sample Pump Failure Zero Drift Problems Site requirements Installation Part Model Sample Connections Drawings Start up of System Allow warm-up for 1 hour Set up for Automatic Sampling Sample System Automatic Operation and Routine Duties Oil in Water Part Teledyne Analytical Instruments Operating Temperature 0-50oC SpecificationsOil in Water Analyzer Appendix Appendix Models QtyP/NDescription Recommended 2-Year Spare Parts List Generic Drawing List Drawing List See manual addendum