Part II, Appendix | Teledyne 6600 specs

Part II: Analysis Unit

3.5 Service Procedures and Adjustments		3-3
3.5.1	Electronics	3-3
3.5.2	Power Supply Test Points	3-3
3.5.3	Setup of the Signal Processing Front-End Amplifier ..	3-3
3.5.4	Oscilloscope Display of the I to E Converter Output ..	3-4

3.5.5Balancing the Optics for Equal Light Transmission

	with Zero Fluid in the Sample Cell	3-5
3.5.6 Setup of the Logarithmic Amplifier		3-6
3.5.7	Inverting Amplifier	3-6
3.5.8	Integrated Reference and Measuring Signals	3-7

3.5.9Battery-Powered Oscilloscope Synchronization Point 3-7

3.6	Interface Board Terminal Strip	3-7
Appendix
A-1	Specifications	A-1
A-2	Recommended 2-Year Spare Parts List	A-3
A-3	Drawing List	A-4

Teledyne Analytical Instruments

Part II: iii

Image 63

Teledyne 6600 manual Part II, Appendix

Contents

Teledyne Analytical Instruments Oil in Water Analyzer Copyright 1999 Teledyne Analytical Instruments Model Iii Table of Contents Model Teledyne Analytical Instruments Part I Control Section Model Installation Ii PartOperation Maintenance Part IAppendix Model 6600 Oil in Water Analyzer Iv Part Oil in Water Analyzer Part I Control Section Overview Main Features of the Analyzer Operator InterfaceIntroduction Model ESCAPE/ENTER Switch Model 6600 Controls, Indicators, and Connectors Model 6600 Interface Panel Control Section Interface Panel Electrical Connections Unpacking the Control/Analysis Unit 115VAC Installation Model Analog Output Connections Examples 10.4 Range Voltage Current mA Alarm Relays Part Data Carrier Detect RS-232 Sig RS-232 Pin Purpose Parameter Setting Command Description Testing the System Part Using the Controls IntroductionOil in Water Analyzer Operation Mode/Function Selection Operation Model Hierarchy of System Functions and Subfunctions System Function Setting up an AUTO-CAL EnteringthePassword Password Protection Installing or Changing the Password Logging Out System Self-Diagnostic Test Checking Linearity with Algorithm Operation Model Model Screen Setting 90% Response time Seconds Digital Filter Setup Set Ultra Sonic Homogenizer on Homogenizer Function Setup Hold/Track Setup Analog 4-20mA Output Calibartion Operation Model Calibration/Hold Timer Setup Manual control of filter and solenoids Algorithm Application Model Outcal Anlz Algorithmapplcation Model Outcal Anlz Zero and Span Functions Zero Cal Auto Mode Zeroing Manual Mode Zeroing Zero Offset Calibration Detector Failure Spanning How the offset value is selected Auto Mode Spanning Manual Mode SpanningOil in Water Analyzer Operation Span Cal Alarms Function Oil in Water Analyzer Operation Range Select Function Auto Screen Precautions Illustrates these schemes graphically Analyze Function Programming Oil in Water Analyzer Operation Set Range Screen Curve Algorithm Screen Auto Mode Linearization Ppm SO2 InputØ Part I Control Section Maintenance Fuse Replacement Analog System Self Diagnostic TestMaintenance Model 6600 Oil in Water Analyzer Power Major Internal Components PreampDetector Side View Open Door Part II Analysis Unit Part II Analysis Section Control/Analysis Unit Ii Part Part II Iv Part Oil in Water Analyzer Operational Theory Method of Analysis Operational Theory Model Optical Bench Photometer Amplifier Automatic Zero System Zero drift may occur in the following cases System Description Source Module Photometer Detector Module Sample Cell Sample Systems User Connections Installing and Connecting the AnalyzerUnpacking the Analyzer Oil in Water Analyzer Part II Analysis Unit Pipe Connections Installation Model Electrical Power ConnectionsSignal and Alarm Output Connections Compressed Air Supply Calibration Calibration Fluids Method One Calibration Automatic operation and routine operational duties Routine MaintenanceOil in Water Analyzer Maintenance System Visual Check and Response Procedure Maintenance Model Routine MaintenanceSuggested Preventive Maintenance Schedule Service Procedures and Adjustments Electronics Power Supply Test PointsSetup of the Signal Processing Front-End Amplifiers Oscilloscope Display of the I to E Converter Output Part Inverting Amplifier Setup of the Logarithmic Amplifier Interface Board Terminals Strip Battery-Powered Oscilloscope Synchronization Point Part Oil in Water Analyzer Maintenance Part Part III Oil in Water Part III Model 6620 Oil in Water Analyzer Table of Contents Part III Model 6620 Oil in Water Analyzer Oil in Water Part Introduction Part Model Method of AnalysisOptical Bench Photometer Amplifier Part III Automatic Zero System From B71046-0 or customer’s piping schematic Oil in Water Piping Diagram B71046 Part Part III System Description Photometer Source ModuleSample Cell Detector Module Control/Analysis UnitPart III Teledyne Analytical Instruments Sampling System Sample Water Preconditioning System Electrical Connections Pressurized Inlet Sample Delivery Zero Water Preconditioning System Homogenizing Ultra clean process applications for leaks into the like Automatic Sample Cell Cleaning System Entering the zero offset Recorder Requirement Signal Outputs Process Alarm System Amplifier PCBAuto Zero Circuit Detector Fail Check Detector signal Signal Failure Alarm Installation Compressed Air Supply Electrical Power ConnectionsSignal and Alarm Output Connections User Connections Safe Vent Drainage Sample Delivery System Electronics Check Installation Check Electrical Check Sample Delivery CheckPreparation for Calibration Manual Sample Introduction Required Calibration Equipment Acquisition of Representative Sample Water Acquisition of Representative Oil Sample Oscilloscope Display of the I to E Converter Output Background Signal Level Determination Part III Part Model Calibration with Prepared Sample Zero Fluid PreparationSpan Fluid Preparation Calibration Setup of Internal Span Flag Calibration Calibration by Correlation with Laboratory Analysis SpanFilterSample System Part III Calibration of the ultrasonic homogenizer Correlation HomogenizerTuning Automatic Operation and Routine Operational Duties Electronics Set-up for Automatic Operation Routine Maintenance System Visual Check and Response Procedure Monthly or 6 weeks maximum Daily Set up of the Signal Processing Front End Amplifiers Service Procedures and Adjustments Set Up of the I to E Converter Set Up of the Logarithmic Amplifier Integrated Reference and Measuring SignalsInverting Amplifier Sample Cell Maintenance Zero Filter Replacement Sample System Maintenance 316 Zero Filter Cleaning Procedure Phototube Replacement Lamp Replacement Lamp Refuses to Light Troubleshooting Section Sample Pump Failure Zero Drift Problems Site requirements Installation Part Model Sample Connections Drawings Start up of System Allow warm-up for 1 hour Set up for Automatic Sampling Sample System Automatic Operation and Routine Duties Oil in Water Part Teledyne Analytical Instruments Specifications Operating Temperature 0-50oCOil in Water Analyzer Appendix Appendix Models QtyP/NDescription Recommended 2-Year Spare Parts List Generic Drawing List Drawing List See manual addendum