Homogenizer Function Setup | Teledyne 6600 instruction

3 Operation		Model 6600

14.5

25.0

35.0

45.5

57.0

69.0

714.0

825.0

946.0

1090.0

At a setting of “zero”, the response time is purely set by the electronics to

4.5seconds. The numbers above can and will change depending on application andtheymerelyservetoillustratetheeffectofthedigitalfilter.

3.3.8 Homogenizer Function Setup

Dependingontheapplication,the6020samplingsystemmayhavean Ultra Sonic Homogenizer. The function of this part is to prevent the oil in the waterfromclumpingtogether.Thehomogenizershouldturnonaftertheinitial warm up and self-diagnostic period when the analyzer enters the Analyze mode. Thehomogenizerwillturnoffautomaticallyassoonastheanalyzerentersthe Zero and Span mode, turning back on at the end.

Undersomeconditions,itmightbedesirabletomanuallyturntheUltra SonicHomogenizeroff. Thehomogenizersetupfunctionisprovidedinthe Systemmenu.ToaccesstheHomogenizerfunctionsetup:

1.EntertheSystemmenu.

2.Select MORE in the first System menu using the UP/DOWN switch.

3.Select HMGNZR in the second System menu, the screen will display

Set Ultra Sonic

Homogenizer: ON

4.By using the UP/DOWN switch the homogenizer can be toggled on and off.

5.Enter or Escape to return to the analyze mode.

3-12 Part I

Teledyne Analytical Instruments

Image 36

Teledyne 6600 manual Homogenizer Function Setup, Set Ultra Sonic Homogenizer on

Contents

Oil in Water Analyzer Teledyne Analytical Instruments Model Copyright 1999 Teledyne Analytical Instruments Table of Contents Iii Model Teledyne Analytical Instruments Model Part I Control Section Installation Ii PartOperation Maintenance Part IAppendix Iv Part Model 6600 Oil in Water Analyzer Overview Oil in Water Analyzer Part I Control Section Main Features of the Analyzer Operator InterfaceIntroduction Model ESCAPE/ENTER Switch Model 6600 Controls, Indicators, and Connectors Model 6600 Interface Panel Control Section Interface Panel Unpacking the Control/Analysis Unit Electrical Connections Installation Model 115VAC Examples Analog Output Connections 10.4 Alarm Relays Range Voltage Current mA Part RS-232 Sig RS-232 Pin Purpose Data Carrier Detect Command Description Parameter Setting Testing the System Part Using the Controls IntroductionOil in Water Analyzer Operation Operation Model Mode/Function Selection Hierarchy of System Functions and Subfunctions System Function Setting up an AUTO-CAL Password Protection EnteringthePassword Installing or Changing the Password Logging Out System Self-Diagnostic Test Operation Model Model Screen Checking Linearity with Algorithm Digital Filter Setup Setting 90% Response time Seconds Homogenizer Function Setup Set Ultra Sonic Homogenizer on Hold/Track Setup Operation Model Calibration/Hold Timer Setup Analog 4-20mA Output Calibartion Algorithm Application Model Outcal Anlz Manual control of filter and solenoids Zero and Span Functions Algorithmapplcation Model Outcal Anlz Auto Mode Zeroing Zero Cal Manual Mode Zeroing Detector Failure Zero Offset Calibration How the offset value is selected Spanning Auto Mode Spanning Manual Mode SpanningOil in Water Analyzer Operation Span Cal Alarms Function Oil in Water Analyzer Operation Range Select Function Auto Screen Precautions Analyze Function Illustrates these schemes graphically Programming Oil in Water Analyzer Operation Set Range Screen Curve Algorithm Screen Auto Mode Linearization Ppm SO2 InputØ Fuse Replacement Part I Control Section Maintenance System Self Diagnostic Test Maintenance Model 6600 Oil in Water AnalyzerPower Analog Major Internal Components PreampDetector Side View Open Door Part II Analysis Section Control/Analysis Unit Part II Analysis Unit Ii Part Part II Iv Part Method of Analysis Oil in Water Analyzer Operational Theory Optical Bench Operational Theory Model Photometer Amplifier Automatic Zero System System Description Zero drift may occur in the following cases Photometer Source Module Sample Cell Detector Module Sample Systems Installing and Connecting the Analyzer Unpacking the AnalyzerOil in Water Analyzer Part II Analysis Unit User Connections Installation Model Electrical Power Connections Signal and Alarm Output ConnectionsCompressed Air Supply Pipe Connections Calibration Calibration Fluids Calibration Method One Routine Maintenance Oil in Water Analyzer MaintenanceSystem Visual Check and Response Procedure Automatic operation and routine operational duties Maintenance Model Routine MaintenanceSuggested Preventive Maintenance Schedule Service Procedures and Adjustments Electronics Power Supply Test PointsSetup of the Signal Processing Front-End Amplifiers Oscilloscope Display of the I to E Converter Output Part Setup of the Logarithmic Amplifier Inverting Amplifier Battery-Powered Oscilloscope Synchronization Point Interface Board Terminals Strip Part Oil in Water Analyzer Maintenance Part Part III Part III Oil in Water Model 6620 Oil in Water Analyzer Table of Contents Part III Model 6620 Oil in Water Analyzer Introduction Oil in Water Part Method of Analysis Optical BenchPhotometer Amplifier Part Model Part III From B71046-0 or customer’s piping schematic Automatic Zero System Oil in Water Piping Diagram B71046 Part Part III System Description Photometer Source ModuleSample Cell Detector Module Control/Analysis UnitPart III Teledyne Analytical Instruments Electrical Connections Sampling System Sample Water Preconditioning System Pressurized Inlet Sample Delivery Homogenizing Zero Water Preconditioning System Automatic Sample Cell Cleaning System Ultra clean process applications for leaks into the like Entering the zero offset Signal Outputs Recorder Requirement Process Alarm System Amplifier PCBAuto Zero Circuit Signal Failure Alarm Detector Fail Check Detector signal Installation Electrical Power Connections Signal and Alarm Output ConnectionsUser Connections Compressed Air Supply Sample Delivery System Safe Vent Drainage Installation Check Electronics Check Electrical Check Sample Delivery CheckPreparation for Calibration Required Calibration Equipment Manual Sample Introduction Acquisition of Representative Oil Sample Acquisition of Representative Sample Water Background Signal Level Determination Oscilloscope Display of the I to E Converter Output Part III Part Model Calibration with Prepared Sample Zero Fluid PreparationSpan Fluid Preparation Calibration Setup of Internal Span Flag Calibration Calibration by Correlation with Laboratory Analysis SpanFilterSample System Part III Calibration of the ultrasonic homogenizer HomogenizerTuning Correlation Electronics Set-up for Automatic Operation Automatic Operation and Routine Operational Duties System Visual Check and Response Procedure Routine Maintenance Daily Monthly or 6 weeks maximum Service Procedures and Adjustments Set up of the Signal Processing Front End Amplifiers Set Up of the I to E Converter Set Up of the Logarithmic Amplifier Integrated Reference and Measuring SignalsInverting Amplifier Sample Cell Maintenance Sample System Maintenance Zero Filter Replacement 316 Zero Filter Cleaning Procedure Lamp Replacement Phototube Replacement Troubleshooting Section Lamp Refuses to Light Zero Drift Problems Sample Pump Failure Site requirements Installation Part Model Sample Connections Drawings Start up of System Allow warm-up for 1 hour Set up for Automatic Sampling Sample System Automatic Operation and Routine Duties Oil in Water Part Teledyne Analytical Instruments Specifications Operating Temperature 0-50oCOil in Water Analyzer Appendix Appendix Models Recommended 2-Year Spare Parts List QtyP/NDescription Drawing List See manual addendum Generic Drawing List