Installing upgrade modules, Firmware Download | Xerox 4500 ps eth

Installation

Xerox 4500 PS ETH, Inst. & Operator's Guide

2.6 Installing upgrade modules

This section provides installation guidelines for IPDS or FSL upgrade modules.

1.Disconnect all cables to the Xerox 4500 PS ETH.

2.Loosen the thumbscrews and pull out the interface

3.Place the upgrade module (be it IPDS or FSL) on the 4 plastic spacers on the base module. Make sure that the pins on the connector J(x) fit correctly.

4.Remount the interface into the printer and fasten th e 2 thumbscrews loosened in step 2.

5.Generate a settings printout to verify the installation of the upgrade module.

The printer and network installation is now complete. For advanced configuration, see the chapter “Configuration”.

FIRMWARE DOWNLOAD

Firmware download when the PrintServer is equipped with a top module can be done easily via PSinst32.

See the next section on Psinst32 for details.

24

Image 24

Xerox 4500 ps eth instruction manual Installing upgrade modules, Firmware Download

Contents

EMC directive Trademarks Preface Prerequisite ManualsRelated Manuals July Table of Contents Novell Setup for IPX/SPX NetBEUI/NetBIOS Printing Using Windows ‘95, NT or OS/2OS/2 Printing Using TCP/IP LPR/LPD 101 Unix Printing Using TCP/IP LPR/LPD 103 PSF/400 AFP Printing Using TCP/IP 11311. AS/400 SCS Printing Using SNA 118 12. AS/400 SCS-DCA Printing Using TCP/IP 121 Problem Determination 146 Appendices163 Items Supplied with Xerox 4500 PS ETH ∙ Product documentationRedirect Introduction to Xerox 4500 PS ETH Direct host printDirect host print via TCP/IP LAN print Supported protocols 1 IPX/SPX protocol NetBEUI/NetBios protocol 2 TCP/IP protocolsSCS-DCA Datastream 4 PU/LU protocol Ida 802.2 protocolEmulation IdaMON Xerox 4500 PS ETH features IllustrationPrintServer Printer Icds System requirements Printers SupportedAll environments Direct AFP print mainframe / midrange Installation of Xerox 4500 PS ETH Pre-Installation taskEU US language settings National language selection Cpgid Example Rear panel Test LAN SES PRTCabling types Test Test key LED indicators PRTLAN SES Sion Installation procedure Installing into Xerox 4505 / 4510 printerBefore you start the installation you must power OFF Installation Xerox 4500 PS ETH, Inst. & Operators Guide Installing into Xerox 4517 printer Installing into Xerox 4520 printer Share timeout Network installationWhen IP address has been defined ∙ Native Share Strings Installing upgrade modules Firmware Download Configuration Introduction to configuration General on Configuration Bootp ServerPsinst32 Minimum configuration Mandatory settingsTCP/IP Mandatory parameters Enable NetWare parameter Enable PuluClass values Subnet mask Set Blocknumber NetBEUI / NetBios Ida Configuration using PSinst32 Program Installation ProcedureWindows ‘95 DLC Installation Procedure Program Execution Windows NT 4.0 DLC Installation Procedure Executing PSinst32 Help Main menu Where do I start with PSinst32? Main Window Program setup Configuring Your Preferred Protocol Here’s how you configure the various protocolsConfigure TCP/IP Configure Snmp Configure SPX/IPX NetWare ENP Configuration Xerox 4500 PS ETH, Inst. & Operators Guide Configure PU/LU SNA Further Options The File Menu Discover RefreshSelect Adaptor Download Select Download Port End of Configuration Downloading Settings to the PrintServer Select DLC download port Boot PrintServer after download Firmware download Example of downloading firmware for PrintServer drivers Broadcasting Name Configuration using Web Browser Access to ida Html configurationRequirements IP address Password Configuration chart Overview Configure PrintServer Main Menu PrintServer Status Menu Configuration using Telnet ExampleTelnet Navigation keys Selecting menu fields Configuring PrintServer Configure PrintServer SubmenuMenu Structure Main Menu Configure Snmp Return to previous menu EnterSelection PrintServer ConfigurationPrintServer ConfigurePrintServer General Parameters Menu TCP/IP Configuration ConfigureTCP/IP 0xx.xxx HostNameDefault Gateway Address Save and Return Return without saving EnterSelection IPX/SPX Configuration EPS PasswordIda 802.2 Configuration NCP preferred DStree PU/LU Configuration ConfigurePU/LU 0xx.xxxNetBios Configuration 05D Snmp Configuration Snmp Manager Access Authorization Selecting Authorize will present the following screen Configure Sessions Change PasswordPrinter YES Save Configuration Restore ConfigurationRestore Factory Default Reboot PrintServer Trace destination Status PrintServer Configuration using Setup File Setup File Identifier??##N1,0# ??space Sample minimum configuration file Idaps Netbios Advanced configuration Enabling Idaps Define SNA Define TCP/IP Printing LPDDefine PPD Printing Ipds Printing Icds See the Define PPD Define NetWare Define ENP session Define NetBEUI/NetBios Define ida Define Printer session Setting Up via Bootp server IP Address Subnet Mask Gateway Address BootfileBootptab Device Entry Bootfile Entry Setting up Bootptab Device EntryNotations used in Bootptab file Microcode File Bootptab Bootp process Setting up the Tftp Daemon Tftp in AIX Environment Tftp in OS/2 Environment Starting the Bootp Server Bootpd -b -d -d -d -d -d Testing PrintServer About the Ping function Novell Setup for IPX/SPX Using the embedded Pserver Embedded Pserver setupEnable NetWare Enable IPX/SPX Set Frametype Before you begin Using the embedded Nprinter Embedded Nprinter setup Printing command example NetWare setup Bindery mode Now make other Nprinter configuration if so required Select Queues Serviced by Printer and press Enter NetWare setup DS mode PrintServer and NW4.1x Configuration Start the Nwadmn95/NTPage Information for ENP Set-up Number ENP Printer in PSinst32 ENP File Server in Psinst32 IDA Start the i-data PrintServer Configuration Tool PSinst32 Trouble Shooting Correct Test Illustration Client NetBEUI/NetBIOS Printing Using Windows ‘95, NT or OS/2 Windows ‘95 and NT Setup OS/2 Setup Net use lptx \\idaxxxxxx\PxPrinterx Changing the default PrintServer Name & Workgroup OS/2 Printing Using TCP/IP LPR/LPD OS/2 printing via a print queue OS/2 printing using LPR command LPR -b -pLPDPrt1 -s192.0.110.1 myprint.pclLprmon -b -pLPDPrt1 -s192.0.110.1 LPT1 Unix Printing Using TCP/IP LPR/LPD AIX printing using TCP/IP LPR/LPDAIX HP-UX Entry Fields 104 SUN OS printing using TCP/IP LPR/LPD Defining the remote printer/plotter using’admintool’’‘ Enable the printer using the admintoolPrinter Name Print Server HP-UX printing with SAM using TCP/IP LPR/LPD Defining the remote printer/plotter using SAMRemote Print Name Windows NT Printing Using TCP/IP LPR/LPD Windows NT version 109 AS/400 Printing Using Host Print Transform and TCP/IP Create a remote output queueRequirements 111 AS/400 printing PSF/400 AFP Printing Using TCP/IP 10.1 AS/400 version 3.1Value must be unique within the network FORMFEED*AUTOCUT Rmtlocnametcpip Configuring WRKAFP2 for direct TCP/IP connection Setting the ChgtcpaAS400PTF 10.2 AS/400 version 3.2 LEXLINK, *IP, *USRDFN Crtpsfcfg version 3.2 only Immed 11. AS/400 SCS Printing Using SNA 11.1 AS/400 controller definition ALL 11.2 AS/400 printer definition 11.3 AS/400 printing 12. AS/400 SCS-DCA Printing Using TCP/IP PS23OUTQ 12.2 AS/400 Printing Text PSF/MVS AFP Printing Using TCP/IP 13.1 PSF/MVS direct attachmentMTU size Sample PSF/MVS JES2 initialisation statements 13.2 PSF/MVS startup procedure PBJ SNA Ipds and SCS Printing from MVS or VM LogmodeIpds printer SCS printer PS PU definition for Vtam definitionDefinition 127 14.3 3174 OS/2 Gateway PS PU definition OS/2 Vtam definition OS/2 Protocol.ini definitions OS/2 CM/2 gateway definitions 130 Host SNA SAA Choose Configure Data Link Adapters Entries look like this Choose Configure Downstream PUs Choose Configure LUs for Downstream PUs Unload nwsaa load nwsaa NET,INACT,ID=puname,F V NET,ACT,ID=puname FSL Configuration FSL Configuration PSS/MVS AFP Printing Using TCP/IP Sample PSS/MVS JES2 initialisation statements PSS printer profile using TCP/IP attachment PSS/VM AFP Printing Using TCP/IP Sample PSS VM printer profile definition using TCP/IP PSF/2 AFP Printing Using TCP/IP Creating a new printer profile Enter the Device Name Enter IP Address Keepalive support for OS/2 Select Port Number 17.3 OS/2 Keepalive configuration PSF/AIX Printing Using TCP/IP Adding TCP/IP attached printerEnter Printer name Enter Internet address Keepalive support for AIX AIX Keepalive support No -a Problem Determination What is SnmpMonitoring tools Snmp support Preparing for use of Snmp PS nameContact name System location LED Status error messages PRT Troubleshooting When installingLAN, and PRT LEDs all flash LAN LED continues to flash PSF indicated communication errors LAN LED is lit but PRT LED is not litMessage AIN1048E or LAN LED is lit, PRT flashes, but no print is produced When configuring What are the symptoms you have recorded or detected? Can you Ping thePrintServer?Are you unable / able to generate a test printout? Unable When printing Has an upgrade of microcode been performed?Successfully Unsuccessfully Excerpt from test page with NetWare settings NetWare settings Printer State Waiting for job Intervention required IRQ Ipds Icds LPD ENP SCS 161 Printer errors in front panel Problem reportingPrinter indicates an error code Appendices Appendix a Configuration Using Setup File Appendix a 1 Configuring via parallel port Appendix a 2 Configuration file parameters Boot SharetimeoutHoldtimeout Irqtimeout Beginconfiguration Session Beginconfiguration Tcpip HostnameEND Inputdef Bootp DefaultipDefaultsm Defaultgw Beginconfiguration Netware LSLFRAME8022 LSLFRAME802SNAPLSLFRAME8023 Lslframedixii Epspassword UserpasswordEpsmode Epsprintserver Beginconfiguration IDA Aliasname Beginconfiguration PU BlockidBeginconfiguration Ppdx Portport Idnumber Beginconfiguration Lpdx Beginconfiguration Enpx PrinternumberResponse Keepalive Beginconfiguration PAR2IN INSTREAMPAR2IN Beginconfiguration Testpgx InstreamtestpgBeginconfiguration IPDS1 Ipdsvp Printserver Beginconfiguration Snaprint Instreamsnaprint Beginconfiguration Icds LanguageselAutoconfig Colorafp Dldtimeout Beginconfiguration Printerx DuplexinstalledOffsetinstalled Afptraydef Papersel PaperdefPapersource Pagewidth Printareaheight LogicalpagexLogicalpagey Logicalpagewidth Rasterop PatternsCtables Languagedef Postscript Traydefx Inputprio Accessauth TrapdestDesthost Trapcommname Access Appendix B Supported FSL Functions Laser Printers Appendix C Microcode upgrading Appendix C.1 Upgrading Microcode via Parallel port Appendix C.3 Upgrading Microcode via TCP/IP Boot Server Preparing for Microcode Upgrade via TCP/IPAppendix C.2 Upgrading Microcode via PSinst32 Update process OS/20uuXXYZZ.B80 Uu020.B80 Microcode level 2, product Appendix C.4 Problem Determination Appendix D idaSetup Ipds configuration If equipped with an Ipds module Appendix E Test printout Test key Appendix F Error messages Error code = %x 0x5110 Appendix G List of abbreviations Appendix H Xerox Product Platform Coax Supported Printers