Manuals / AT&T / Communications / Cordless Telephone

AT&T IPC-1600 manual Sample Configuration Record

Models: IPC-1600

1 167

Download 167 pages 27.5 Kb

<>

Performance Characteristics Install Error codes PIN Signal Name Signal Flow Default factory IRQ level Connecting Port Modular Cables Warranty Modifying Kernel Configuration IPC-1600 Diagnostics Accessing Serial Ports

Page 115

Sample Configuration Record

A-14 IPC-1600 USER’S GUIDE

Page 114 Page 116

Image 115

AT&T IPC-1600 manual Sample Configuration Record

Page 114 Page 116

Related pages All Configuration page Configuring NPort Monitor for Moxa Technologies DE-308 Configurar la política de inactividad Wi-Fi for Samsung SM-P6050ZWEPHE Configure Alerts for New Video Clips for LG Electronics VX9400MMBB0222401(1.0) Configuration du Mode Jeu for Samsung LS27E591CS/EN SWTICHconfig# dot1x system-auth-control for Siemens S323 Une fois la configuration initiale effectuée for Sylvania LC427SSX Guidelines for Configuring Your Network for iSCSI for Dell 3000i Cómo cambiar la configuración de Pais for JVC AV28X25EU Click Next to bring up the configuration interface for B&B Electronics EIR505-XX Memory Detection and Configuration for Compaq W4000 Where can I find the Samsung BN68 specs?

Contents

AT&T Page Table of Contents MS-DOS Device Driver Installation System Features Appendices AT&T IPC-1600 Ports Cabinet IPC-1600 USER’S Guide Figure A-1 List of Figures Preface Limited Warranty Limited Warranty RF Interference Warning Trademarks Ordering Information Training Information Overview Guide Organization Guide Organization What Is an IPC-1600? What Is an IPC-1600? IPC-1600 Architecture Ports and Drivers Information in the Examples Hexadecimal Notation Native MS-DOS and Unix System Operation MS-DOS and Unix System IPC-1600 Use Strategy Native MS-DOS Operation MS-DOS Under Simul-Task and Unix System Operation MS-DOS Device Driver Installation Introduction Installation Procedure Preconfigure the IPC-1600 Boards Load the Software Install the Hardware Copy the files from the a drive to the C drive Create or Modify the CONFIG.SYS File Execute IPC16CNF to Configure the Driver Number of Boards Option Start Channel Number Option Channel Parameters Option Dsbl Enbl None XON/XOFF RTS/CTS Both Finishing Up Reboot the System Reconfigure the Boards If Necessary Accessing Serial Ports Removing the MS-DOS Device Driver Removing the MS-DOS Device Driver Limitations of the IPC-1600 MS-DOS Device Driver Unix System Device Driver Installation Unix System Device Driver Installation IPC-1600 Tunable Parameters System Memory 2MB 4MB 8MB Tunable Parameters and Memory Guidelines IPC-1600 System Memory Guidelines Number General Installation Procedures Specify the Type of Installation Installation Procedures Installation Procedures Specify Shared or Board-Unique Hardware Interrupt Assignment Specify Shared or Board-Unique Controller Memory Assignment Unix System Device Driver Installation Specify the Number of Boards Assigning Board-Unique Hardware Interrupt Request Level Assigning an I/O Address Enter Assigning Board-Unique Starting Controller Memory Address LPC-1600 USER’S Guide Confirming the Data Type IRQ Completing Driver Installation Once the kernel has been rebuilt, another message displays Changing IPC-1600 Configuration Modifying Kernel ConfigurationRemoving All IPC-1600 Boards Hardware Installation Hardware Installation Preparation Prepare Machine for Installation Set the Controller Memory Starting Address Prepare the IPC-1600 for Installation Connect the 16-Ports Fanout Module Cables Connect the Ribbon Cables to IPC-1600 Install the Board Managing the Serial Ports Managing the Serial Ports Node Names Definition of IPC-1600 Device Node Names IPC-1600 Device Names for Ports 1 through Board Number Software Device Class Hardware Device Class IPC-1600 Administration Via hipcutils Unix System V Release Administration Via Face Unix System V Release 3.2 Administration Via Face System Features Features Features Raw Mode Cooked Mode Performance Characteristics Performance Characteristics Power Consumption Troubleshooting the Intelligent Ports Card Troubleshooting the Intelligent Ports Card MS-DOS Boot Error Message Copy Diagnostics to the System Disk IPC-1600 Diagnostics Copy the file from the a drive to the C drive IRQ = How to Run Diagnostics Total Pass Total Host 64KB Dual-Ported Memory Tests IPC-1600 Test Descriptions IPC-1600 Communication Ports Tests Helpful Hints Helpful Hints Appendix a Hardware Parameter Settings Hardware Parameter Settings A-1 Switch, Jumper, Connector Location Information Switch, Jumper, Connector Location Information DS1 Switch Settings-Controller Memory Starting Address DS1 Switch Settings-Controller Memory Starting Address Default factory controller memory starting address DS1 Controller Memory Starting Address Settings Cont’d Hardware Parameter Settings A-7 DS1 Switch Settings-I/O Port Address Default factory I/O port address Figure A-4 DS2 Interrupt Request Level Default Setting DS2 Switch Settings-Interrupt Request Level Default factory IRQ level Local Program Memory Size Select Jumper J1 Sample Configuration Record Sample Configuration Record Appendix B Serial Input/Output Device Interface Serial Port Characteristics Figure B-1 RS-232C Voltage Envelope Voltage Envelope Serial I/O Device Interface B-3 IPC-1600 80-Pin Headers P3 and P4 IPC-1600 80-Pin Headers P3 and P4 Serial I/O Device Interface B-5 PIN Signal Name Number P4 Connector P3 Connector Ports Fanout Module Assembly Figure B-3 16-Ports Fanout Module Assembly PIN Signal Name Signal Flow RJ-45 Type Modular Jack Connector AT&T Null Modem Adapter Data Terminal Equipment DTE ConnectionsAT&T Straight Thru Adapter Figure B-5 AT&T Null Modem Adapter Connection Diagram Figure B-6 AT&T Straight Thru Adapter Connection Diagram AT&T Terminal/Printer Adapters Pin to DB-25 DTE Adapters Figure B-7 AT&T Terminal/Printer Adapter Connection Diagram Figure B-8 AT&T Printer DTR Adapter Connection Diagram AT&T ACU/MODEM DCE Adapters Data Circuit-Terminating Equipment DCE ConnectionsAT&T Remote Console Adapter Figure B-9 AT&T ACU/MODEM DCE Adapter Connection Diagram Figure B-10 AT&T Remote Console Adapter Connection Diagram Serial I/O Device Interface B-19 Conductor Modular Cables Conductor Modular Cables AT&T 10-Pin Extender Adapter Figure B-12 AT&T 10-Pin Extender Adapter Connection Diagram Compatibility with Other I/O System Cabling IPC-1600 Equipment IPC-802 Equipment Intelligent Ports Card Model 802 IPC-802 Interface 3B2 Computer PORTS/EPORTS Interface Example a Equipment Description Comcode PEC Label Adapter and Cable Ordering Information Serial I/O Device Interface B-27 Adapter Use Information Adapter Use Information Appendix C AT&T IPC-1600 Ports Cabinet General Description What is Included?Purpose General Instructions Installation Information Routing and Connecting Ribbon Cables to Fanout Module Securing the Wire-Frame AssemblyChoosing a Mounting Location Connecting Port Modular Cables Installing the 16-Ports Fanout Module Figure C-1 AT&T IPC-1600 Ports Cabinet Figure C-2 AT&T IPC-1600 Ports Cabinet Assembly Drawing Glossary Bios DCE Duart FEP Glossary GL-5 Null device Glossary GL-7 GL-8 IPC-1600 USER’S Guide Index IN-2 IPC-1600 USER’S Guide N F I G . S Y S File, 2 IN-4 IPC-1600 USER’S Guide Index IN-5 IN-6 IPC-1600 USER’S Guide Index IN-7 305-920 Graphics 1988 AT&T

Top Page Image Contents