Manuals / AT&T / Communications / Cordless Telephone

AT&T IPC-1600 manual Unix System Device Driver Installation

Models: IPC-1600

1 167

Download 167 pages 27.5 Kb

Performance Characteristics Install Error codes PIN Signal Name Signal Flow Default factory IRQ level Connecting Port Modular Cables Warranty Modifying Kernel Configuration IPC-1600 Diagnostics Accessing Serial Ports

Page 47

Image 47

Chapter 3: UNIX System Device Driver

Installation

Page 46 Page 48

Image 47

AT&T IPC-1600 manual Unix System Device Driver Installation

Page 46 Page 48

Our partner
Обсуждение вопроса Как долго может существовать компания с уплаченным уставным капиталом? из чата CY Law, Visas, Taxes, Insurance, Кипр

Related pages All Install page Quick Installation for Tripp Lite I Installing The Remote Unit for Network Technologies ST-C5KVM2ARS-1000S Installing the Zone Keypads for M&S Systems XDM4600 Installation for Pride Mobility SilverStar Before Installation for JVC LVT1437-001A Typical Sewage Installation for Wayne 200000-015 Installation for Beko CXFD 6114B Graphics Card Installation for MSI Z87-MPOWER-MAX Mower Removal Installation for Snapper 19HP Installing a VRM for Dell 450 Can I find a video tutorial for using the Husqvarna R150SV?

Contents

AT&T Page Table of Contents MS-DOS Device Driver Installation System Features Appendices AT&T IPC-1600 Ports Cabinet IPC-1600 USER’S Guide Figure A-1 List of Figures Preface Limited Warranty Limited Warranty RF Interference Warning Trademarks Ordering Information Training Information Overview Guide Organization Guide Organization What Is an IPC-1600? What Is an IPC-1600? IPC-1600 Architecture Ports and Drivers Information in the Examples Hexadecimal Notation Native MS-DOS and Unix System Operation MS-DOS and Unix System IPC-1600 Use Strategy Native MS-DOS Operation MS-DOS Under Simul-Task and Unix System Operation MS-DOS Device Driver Installation Introduction Installation Procedure Preconfigure the IPC-1600 Boards Load the Software Install the Hardware Copy the files from the a drive to the C drive Create or Modify the CONFIG.SYS File Execute IPC16CNF to Configure the Driver Number of Boards Option Start Channel Number Option Channel Parameters Option Dsbl Enbl None XON/XOFF RTS/CTS Both Finishing Up Reboot the System Reconfigure the Boards If Necessary Accessing Serial Ports Removing the MS-DOS Device Driver Removing the MS-DOS Device Driver Limitations of the IPC-1600 MS-DOS Device Driver Unix System Device Driver Installation Unix System Device Driver Installation IPC-1600 Tunable Parameters System Memory 2MB 4MB 8MB Tunable Parameters and Memory Guidelines IPC-1600 System Memory Guidelines Number General Installation Procedures Specify the Type of Installation Installation Procedures Installation Procedures Specify Shared or Board-Unique Hardware Interrupt Assignment Specify Shared or Board-Unique Controller Memory Assignment Unix System Device Driver Installation Specify the Number of Boards Assigning Board-Unique Hardware Interrupt Request Level Assigning an I/O Address Enter Assigning Board-Unique Starting Controller Memory Address LPC-1600 USER’S Guide Confirming the Data Type IRQ Completing Driver Installation Once the kernel has been rebuilt, another message displays Removing All IPC-1600 Boards Modifying Kernel ConfigurationChanging IPC-1600 Configuration Hardware Installation Hardware Installation Preparation Prepare Machine for Installation Set the Controller Memory Starting Address Prepare the IPC-1600 for Installation Connect the 16-Ports Fanout Module Cables Connect the Ribbon Cables to IPC-1600 Install the Board Managing the Serial Ports Managing the Serial Ports Node Names Definition of IPC-1600 Device Node Names IPC-1600 Device Names for Ports 1 through Board Number Software Device Class Hardware Device Class IPC-1600 Administration Via hipcutils Unix System V Release Administration Via Face Unix System V Release 3.2 Administration Via Face System Features Features Features Raw Mode Cooked Mode Performance Characteristics Performance Characteristics Power Consumption Troubleshooting the Intelligent Ports Card Troubleshooting the Intelligent Ports Card MS-DOS Boot Error Message Copy Diagnostics to the System Disk IPC-1600 Diagnostics Copy the file from the a drive to the C drive IRQ = How to Run Diagnostics Total Pass Total Host 64KB Dual-Ported Memory Tests IPC-1600 Test Descriptions IPC-1600 Communication Ports Tests Helpful Hints Helpful Hints Appendix a Hardware Parameter Settings Hardware Parameter Settings A-1 Switch, Jumper, Connector Location Information Switch, Jumper, Connector Location Information DS1 Switch Settings-Controller Memory Starting Address DS1 Switch Settings-Controller Memory Starting Address Default factory controller memory starting address DS1 Controller Memory Starting Address Settings Cont’d Hardware Parameter Settings A-7 DS1 Switch Settings-I/O Port Address Default factory I/O port address Figure A-4 DS2 Interrupt Request Level Default Setting DS2 Switch Settings-Interrupt Request Level Default factory IRQ level Local Program Memory Size Select Jumper J1 Sample Configuration Record Sample Configuration Record Appendix B Serial Input/Output Device Interface Serial Port Characteristics Figure B-1 RS-232C Voltage Envelope Voltage Envelope Serial I/O Device Interface B-3 IPC-1600 80-Pin Headers P3 and P4 IPC-1600 80-Pin Headers P3 and P4 Serial I/O Device Interface B-5 PIN Signal Name Number P4 Connector P3 Connector Ports Fanout Module Assembly Figure B-3 16-Ports Fanout Module Assembly PIN Signal Name Signal Flow RJ-45 Type Modular Jack Connector AT&T Straight Thru Adapter Data Terminal Equipment DTE ConnectionsAT&T Null Modem Adapter Figure B-5 AT&T Null Modem Adapter Connection Diagram Figure B-6 AT&T Straight Thru Adapter Connection Diagram AT&T Terminal/Printer Adapters Pin to DB-25 DTE Adapters Figure B-7 AT&T Terminal/Printer Adapter Connection Diagram Figure B-8 AT&T Printer DTR Adapter Connection Diagram AT&T Remote Console Adapter Data Circuit-Terminating Equipment DCE ConnectionsAT&T ACU/MODEM DCE Adapters Figure B-9 AT&T ACU/MODEM DCE Adapter Connection Diagram Figure B-10 AT&T Remote Console Adapter Connection Diagram Serial I/O Device Interface B-19 Conductor Modular Cables Conductor Modular Cables AT&T 10-Pin Extender Adapter Figure B-12 AT&T 10-Pin Extender Adapter Connection Diagram Compatibility with Other I/O System Cabling IPC-1600 Equipment IPC-802 Equipment Intelligent Ports Card Model 802 IPC-802 Interface 3B2 Computer PORTS/EPORTS Interface Example a Equipment Description Comcode PEC Label Adapter and Cable Ordering Information Serial I/O Device Interface B-27 Adapter Use Information Adapter Use Information Appendix C AT&T IPC-1600 Ports Cabinet Purpose What is Included?General Description General Instructions Installation Information Choosing a Mounting Location Securing the Wire-Frame AssemblyRouting and Connecting Ribbon Cables to Fanout Module Connecting Port Modular Cables Installing the 16-Ports Fanout Module Figure C-1 AT&T IPC-1600 Ports Cabinet Figure C-2 AT&T IPC-1600 Ports Cabinet Assembly Drawing Glossary Bios DCE Duart FEP Glossary GL-5 Null device Glossary GL-7 GL-8 IPC-1600 USER’S Guide Index IN-2 IPC-1600 USER’S Guide N F I G . S Y S File, 2 IN-4 IPC-1600 USER’S Guide Index IN-5 IN-6 IPC-1600 USER’S Guide Index IN-7 305-920 Graphics 1988 AT&T

Top Page Image Contents