Preparing Your Site for Installation | Cisco Systems 2.7 specs

Chapter 2 Preparing to Install WLSE 1130-19 Hardware

Preparing Your Site for Installation

Preventing EMI

When you run wires for any significant distance in an electromagnetic field, electromagnetic interference (EMI) can occur between the field and the signals on the wires.

Note that:

•Bad plant wiring can result in radio frequency interference (RFI).

•Strong EMI, especially when it is caused by lightning or radio transmitters, can destroy the signal drivers and receivers in the system, and can even create an electrical hazard by conducting power surges through lines and into the system.

To predict and remedy strong EMI, consult RFI experts.

Preparing Your Site for Installation

This section describes the requirements your site must meet for safe installation and operation of your WLSE. Ensure that your site is properly prepared before beginning installation.

Environmental

When planning your site layout and equipment locations, keep in mind the precautions described in this section to help avoid equipment failures and reduce the possibility of environmentally caused shutdowns. If you are currently experiencing shutdowns or unusually high errors with your existing equipment, these precautions will help you isolate the cause of failures and prevent future problems.

	Installation and Configuration Guide for the CiscoWorks Wireless LAN Solution Engine
78-16345-01	2-7

Image 43

Cisco Systems 2.7 warranty Preparing Your Site for Installation, Preventing EMI, Environmental

Contents

Corporate Headquarters Copyright 2004 Cisco Systems, Inc. All rights reserved Iii N T E N T S Safety Verifying the Configuration Setting Up Discovery and Device Management-CiscoWorks Vii Quick Reference A-4 Viii Cisco 90-Day Limited Hardware Warranty Terms Replacement, Repair, or Refund Policy for Hardware Duration of Hardware WarrantyTo Receive a Return Materials Authorization RMA Number Cisco 90-Day Limited Hardware Warranty Terms Xii Preface Xiv AudienceConventions Convention Bewaar Deze Instructies Xvi Warnung Wichtige Sicherheitshinweise Xvii Avvertenza Importanti Istruzioni Sulla Sicurezza Xviii Guarde Estas Instrucciones Xix Document Title Description Product Documentation Xxi Cw1105/wlse/27/index.htm Xxii Obtaining DocumentationCisco.com Ordering Documentation Obtaining Technical Assistance Documentation FeedbackCisco TAC Website TAC Case Priority Definitions Opening a TAC CaseXxiv Obtaining Additional Publications and Information Xxvi Supplemental License Agreement Installation and Use Reproduction and Distribution Software Upgrades, Major and Minor ReleasesXxviii Product Overview Software Features Front Panel Features Hardware Features-WLSE1130-19 Indicator Color Function System Indicators 2shows the Wlse back panel Back Panel Features Serial/Console Port Pin Signal DefinitionShell Network Cable Requirements Ethernet Connectors Equipment Included in the Package Safety Preparing to Install Wlse Hardware Preparing to Install Wlse 1130-19 Hardware Safety 78-16345-01 General Precautions Maintaining Safety with Electricity Protecting Against Electrostatic Discharge Preventing EMI Preparing Your Site for InstallationEnvironmental Grounding the System Choosing a Site for Installation Cabling AC PowerCreating a Safe Environment Precautions for Rack-Mounting Preparing to Install Wlse 1130-19 Hardware Next Step Tools and Equipment Required for Installation Installing Wlse 1130-19Hardware Installing the Wlse 1130-19 in a Rack Installation Quick Reference 78-16345-01 Rack Rail Components Removing the Server Rail Telescoping the Rail Attaching Front Rail to the Rack See -5. Attach the back end of the rail to the rack Attaching Screws to Telescopic Rail Attaching Chassis to Rail See -8. Insert the chassis in the rack 10 Attaching Management Arm 11 Installing Cable in Management Arm 12 Fastening the Server into the Rack Connecting Cables Connecting to the AC Power SourceCable Powering On the Wlse Next Step-Configuration Basic Setup-CiscoWorks 1105/1130/1130-19 Initial Setup Quick Reference Guidelines for Using the Setup Program Configuring the WLSE’s Network InformationRunning the Setup Program Prompt Response Description IP address of default router 209.165.200.224 Prompt Response Description Sample Response Wlse Without a DNS Server, page 4-6 before Mailroute hostname ip-address Changing the Configuration After Running Setup Configuring the Wlse Without a DNS Server Configuring Name ResolutionNo ip name-server ip-address # nslookup dns-name Verifying the Configuration Supported Browsers Configuring the Web Browser Select Tools Internet Options Configuring Internet ExplorerSelect Enable for Scripting of Java applets Client Operating System Supported Browsers Select Edit Preferences Configuring Netscape Navigator Logging into the Web Interface and Verifying Connectivity Select Enable all cookies Adding Users Select Administration User Admin Manage UsersHttp//209.165.202.1281741 Next Steps-Set Up Devices and Configure Device Management 78-16345-01 Setting Up Non-IOS Access Points and Bridges Tasks Procedure Set Up Using the Web InterfaceCisco Discovery Protocol and select Click User Manager Click Security Set Up Using a Wlse Configuration Template Setting Up IOS Access PointsBasic Network Management Setup-IOS Devices Using the AP CLI for Network Management Setup Configure the read-only community Using the AP Web Interface for Network Management Set Up Select Services Telnet/SSH Select Services Telnet/SSH Enable Secure ShellSelect Services Snmp Select Read-Write Select Read-Only Radio Management Setup-IOS Devices About WDS Devices About Configuring Authentication Using Access Points as WDS Devices Radio Management Setup Quick Reference Select Configure Wireless Network Manager Select Wireless Services WDS Select Wireless Services AP Under Use Group For, select Infrastructure Authentication Define a server group for infrastructure authentication Click Create New Select Configure TemplatesSelect Security Server Manager Select Wireless Services AP Configuration Using the Web Interface to Configure Infrastructure APs Using a Wireless LAN Services Module WSM as the WDS Device Wlccp ap username username password password Configuring Scanning APs Configuring a Scanning AP-Using the AP CLI Confirming the Configuration Configuring the Wlse Select Wireless Services WDS WDS Status Using the Web-based Interface to Validate the Configuration Mode and use the set snmp community read-only Setting Up Routers and SwitchesTask Procedure Snmp community communitystring ro command Snmp location location Setting Up AAA ServersHostname name Snmp contact contact Procedure Field Description 78-16345-01 Tasks References Device Management Quick Reference Select Devices Discover Device Credentials Snmp Communities Adding Device Credentials to the Wlse Enter Http Credentials for Non-IOS Access Points Enter Telnet or SSH Credentials for IOS Access Points Enter Wlccp Credentials for Wireless Domain Services WDS Enter Http Port Settings for IOS Access Points Select Devices Discover AAA Server Adding AAA Servers to the WlseText Box Description Discovering Devices Configuring Discovery OptionsSelect Devices Discover Discover Advanced Options Run CDP Discovery Now Run CDP Discovery 78-16345-01 Modify the CDP Discovery Schedule Import Devices from a File Import Devices Import Devices from a CiscoWorks Server Select Devices Discover Managed Devices Managing Devices Next Step Installing Software-CiscoWorks 1105/1130/1130-19 Downloading the Upgrade Image Upgrade VersionsBacking Up the Wlse Upgrade Methods Installing from the Local Repository Upgrading by Using the Web InterfaceQuick Reference Field Data to Enter Select Administration Appliance Software Define Repository Installing from a Windows Server Appliance Software Status View Log Upgrading by Using the CLI Create a Local Repository Create the Repository Create a Repository on a Windows Server Install the Software Related CLI Commands Upgrading from the Recovery CD Reimaging the WLSE-Local Installation Method At the following prompt, enter yes to start the Recovery CD Reimaging the WLSE-Remote Installation Method Component Specifications Technical Specifications CiscoWorks Appendix B Technical Specifications- CiscoWorks IN-1 D E IN-2 WDS IN-3 CDP IN-4 IN-5 IN-6 Snmp IN-7 IN-8