3 C7LSE CCS SS7 Link Set End | Dialogic SS7G2X guide

Dialogic® SS7G2x Signaling Server SGW Mode User Manual Issue 4

6.6.3C7LSE – CCS SS7 Link Set End

Synopsis

This command is used to end the SS7 link set.

Syntax

C7LSE:LS=;

Prerequisites

•

•

•

There should be no signaling links attached to the link set.

All configured SS7 links within the system must be blocked.

Note: After blocking, an SS7 link cannot be unblocked until all the boards processing the SS7 signaling are blocked and then unblocked.

There are no C7 Routes using this link set.

Attributes

CONFIG

Examples

C7LSE:LS=1;

6.6.4C7LSP – CCS SS7 Link Set Print

Synopsis

This command obtains a printout of the attributes for the SS7 link set. If no link is specified, the values for all link sets are shown.

Syntax

C7LSP:[LS=,];

Prerequisites

None

Attributes

None

Examples

C7LSP;

Output Format

CCS SS7 Link Set
LS	NC	OPC	DPC	NI	LSSIZE	SS7MD
1	1	1	3	2	2	ITU14
2	2	2	4	0	2	ANSI
EXECUTED

69

Image 69

Dialogic SS7G2X manual 3 C7LSE CCS SS7 Link Set End, 4 C7LSP CCS SS7 Link Set Print

Contents

Dialogic SS7G2x Signaling Server Publication Date September Document Number Contents Contents 11.4 13.8 Snnae Sigtran Network Appearance End Tables Revision HistoryIndex Overview General DescriptionRelated Information Part Numbers Applicability Hardware OverviewConnectivity User Interface Signaling Configuration and Program StorageIP Security Functional Summary Configuration Model Cross ConnectionsMonitoring Alarm Log Remote Data Centres7 M3UA Backhaul Operation Default Routing 8 M2PA Longhaul OperationResilience IP Resilience Dual Operation Dual Resilient Configuration Specification Installation Installation and Initial ConfigurationConnecting a VT100 Terminal Software Download Configuration is displayed in the format shown below Initial Configuration Telnet terminal displays the MML interface prompt Configuration Procedure Log On/Off Procedure OperationGeneral Command Character Set and Syntax Command FormatsCommand Entry Changing Configuration Data Command ResponsesCommand Rejection Responses FTP Access Software Update from a Remote Data Centre Software Backup to a Remote Data CentreSoftware Update from CD-ROM Backing Up System Software Software Update from Startup Using FTP Software Update from StartupSoftware Update from Startup Using a CD Backing Up Configuration Data Configuration Update from a Remote Data Centre Updating Configuration DataConfiguration Update from CD ROM Configuration Update from Startup Purchasing System Licenses System Licenses License Update from Remote Data Centre Installing System Licenses License Update by FTP Parameter Definitions Parameter TableParameter Definitions Date Config License DuplexDbits Dest Ftpser FtppwdGateway Hport LS1 PasswordLS2 Lssize Pcmtype ResetPCR PER Soft Normal RestartHalt RKI Speed AutoSrtx SS7MD Remote Operation Types Remote Operations Signaling Gateway Specific Timers Signaling Gateway Timers Signaling Gateway-Specific TimersMTP3 ITU Timers MTP3 Ansi Timers Board Types SCTP-Specific Timers Command Groups Command DefinitionsCommand Notation Command Attributes Alarm Commands Alclp Alarm Class Print Alcls Alarm Class Set Alfcp Alarm Fault Code Print Allip Alarm List Print Diag CLA Occurred Cleared Title Allop Alarm Log Print Altei Alarm Test Initiate Alrei Alarm Reset Initiate Altee Alarm Test End Configuration Commands Cnboe Configuration Board End Cnboi Configuration Board Initiate Cnbui Configuration Back Up Initiate Cnbop Configuration Board Print Cnmoe Configuration Monitor End Cnmoi Configuration Monitor Initiate Cnpci Configuration PCM Initiate Cnmop Configuration Monitor Print Cnpce Configuration PCM End Cnpcc Configuration PCM Change Cnrdi Configuration Remote Data Centre Initiate Cnpcp Configuration PCM Print Cnrde Configuration Remote Data Centre End Cnrdc Configuration Remote Data Centre Change Cnswp Configuration Software Print Cnrdp Configuration Remote Data Centre Print See .6.1, IP Port Bonding on page 142 for more information Cnsys Configuration System Set CNSYSSYSID=STATION1,PER=2,IPADDR=255.123.0.123 Cnsyp Configuration System Print Cntdp Configuration Time And Date Print Cntds Configuration Time and Date Set Cntop Configuration Timeout Value Print Cntos Configuration Timeout Value Set Cntsp Configuration Timeslot Print Cnupi Configuration Update Initiate Cnxce Configuration Cross Connect End Cnxci Configuration Cross Connect Initiate Cnxcp Configuration Cross Connect Print SS7 Signaling Commands 1 C7LSI CCS SS7 Link Set Initiate 2 C7LSC CCS SS7 Link Set Change 4 C7LSP CCS SS7 Link Set Print 3 C7LSE CCS SS7 Link Set End 5 C7RTI CCS SS7 Route Initiate 6 C7RTC CCS SS7 Route Change 8 C7RTP CCS SS7 Route Print 7 C7RTE CCS SS7 Route End 9 C7SLI CCS SS7 Signaling Link Initiate 10 C7SLC CCS SS7 Signaling Link Change 12 C7SLP CCS SS7 Signaling Link Print 11 C7SLE CCS SS7 Signaling Link End IP Commands Ipepp Display Ethernet Port Speed Ipeps Set Ethernet Port Speed Ipgwe Internet Protocol Gateway End Ipgwi Internet Protocol Gateway Initiate Ipgwp Internet Protocol Gateway Print MML Commands Mmlop MML Log Off Print Mmloi MML Log Off Initiate Mmptc MML Port Change Mmlos MML Log Off Set Mmptp MML Port Print Maintenance Commands Mnbli Maintenance Blocking Initiate Mnble Maintenance Blocking End Mnine Maintenance Inhibit End Mnini Maintenance Inhibit Initiate Mnrsi Maintenance Restart System Initiate Measurement Commands 10.1 MSC7P Measurements SS7 Print C7LINK Ossdur Msepp Measurement Ethernet Port Print ETH Mspcp Measurements PCM Print Msslp Measurements Sigtran Link Print Mssyp Measurements System Print Remote Data Centre Commands Limitations Rdcri Remote Data Centre Continuous Record Initiate Record must already be initiated Rdcrc Remote Data Centre Continuous Record Change Rdcrp Remote Data Centre Continuous Record Print Rdcre Remote Data Centre Continuous Record End Rdpde Remote Data Centre Periodic Data End Rdpdi Remote Data Centre Periodic Data Initiate Rdpdp Remote Data Centre Periodic Data Print Rdpri Remote Data Centre Periodic Report Initiate Rdpre Remote Data Centre Periodic Report End Rdprc Remote Data Centre Periodic Report Change Rdprp Remote Data Centre Periodic Report Print Signaling Gateway Commands Sgdpc Signaling Gateway Destination Point Change Sgdpi Signaling Gateway Destination Point Initiate Sgdpp Signaling Gateway Destination Point Print Sgdpe Signaling Gateway Destination Point End Sgiri Signaling Gateway Incoming Route Initiate Sgire Signaling Gateway Incoming Route End Sgirc Signaling Gateway Incoming Route Change Sgirp Signaling Gateway Incoming Route Print Sgrki Signaling Gateway Routing Key Initiate Sgrkp Signaling Gateway Routing Key Print Sgrke Signaling Gateway Routing Key End Sigtran Commands Snale Sigtran Application Server List End Snali Sigtran Application Server List Initiate Snapi Sigtran Application Server Initiate Snalp Sigtran Application Server List Print Snapp Sigtran Application Server Print Snape Sigtran Application Server End Snnae Sigtran Network Appearance End Snnai Sigtran Network Appearance Initiate Snnap Sigtran Network Appearance Print Snlink Snsli Sigtran Signaling Link Initiate Snsle Sigtran Signaling Link End Snslc Sigtran Signaling Link Change Snslp Sigtran Signaling Link Print Status Commands Stalp Status Alarm Print Stapp Status Application Server Print Stbop Status Board Print Possible Route Status values are Available Unavailable Stcrp Status C7 Route Print 14.5 STC7P Status C7 Link Print Stepp Status Ethernet Port Print Stipp Status IP Print Stpcp Status PCM Print Strdp Status Remote Data Centre Print Stslp Status Sigtran Link Print Stsyp Status System Print Multiple IP Networks Configuration Overview Boards and PCMs Signaling Configuration 1 SS7 Configuration SS7 M2PA Operation SS7 MTP2 Operation M2PA Example 2 M3UA Configuration M3UA Backhaul Example Routing Configuration Routing Configuration Example Management and Operations Configuring Default RoutingRouting MSUs Route Set Test Resilience IP Port Bonding System Using Default Routing Configuration Dual Resilient OperationOverview of Dual Resilience Example 2.3 M2PA Inter Unit Signaling Links Multihoming On Signaling Gateway 2, configure the link sets as follows Alarm Fault Codes Alarm Fault Code ListingSIG CRT SYS SYS PSU ID CRT MJRAIS SIG SYS CPU ID MJRNone MJR SYS MJR Record SYS MRN SIG MJR Remote Data Centre Operation Sigtran Link Traffic Measurements Alarm Record File FormatEthernet Port Traffic Measurements System Measurements PCM Measurements File Format Ethernet Port Measurements File Format 4 SS7 Link Measurements File Format Sigtran Link Measurements File Format RDC Configuration and UsageSystem Measurements File Format RDC Initialization Alarm Data SS7 Signaling Link Traffic MeasurementsPeriodic Reports Configuration Backup Software UpdateConfiguration Update Software Option Installation From RFC1155-SMI OBJECT-TYPE SS7G2x Snmp MIB = datakinetics Top level nodes within DK4032 MIB DkSysInfo Worked Configuration Examples Backhaul Configuration11.2 M2PA Longhaul Configuration SEP2 11.3.2 SG 2 Configuration 11.3.1 SG 1 Configuration Alarm Commands Command SummaryConfiguration Commands CCS SS7 Signaling Commands MML Commands IP CommandsMaintenance Commands Measurement Commands Signaling Gateway Commands Sigtran CommandsStatus Commands ASP Glossary SEP CD-ROM Index Mnble Mnbli Mnine Mnini Sgdpe Sgdpi Sgdpp Sgirc Sgire Sgiri Sgirp Sgrke Sgrki