Mspcp Measurements PCM Print | Dialogic SS7G2X guide

Chapter 6 Command Definitions

6.10.3MSPCP – Measurements PCM Print

Synopsis

This command prints traffic measurements for PCMs. The measurements are cumulative between system startup and the next time the measurements are reset.

The fields have the following meanings:

•PCM - PCM on a board

•FMSLIP - Frame Slip count

•OUTSYN - Out-sync transitions

•ERRSEC - Errored Seconds count

•SEVSEC - Severely Errored seconds count

•PERIOD - Time since measurements on the route were last reset. Specified in hours, minutes and seconds

Syntax

MSC7P:[C7LINK=,][RESET=,];

Prerequisites

•If specified, the PCM must be initiated and on an unblocked board.

Attributes

None

Examples

MSPCP:PCM=5-1;

MSPCP;

Output Format

PCM Traffic Measurements
PCM	FMSLIP	OUTSYN	ERRSEC	SEVSEC	PERIOD
3-3	57	60	23	1	23:00:00
3-4	12	35	33	4	01:00:00
4-4	53	55	4	0	01:00:00

EXECUTED

94

Image 94

Dialogic SS7G2X manual Mspcp Measurements PCM Print

Contents

Dialogic SS7G2x Signaling Server Publication Date September Document Number Contents Contents 11.4 13.8 Snnae Sigtran Network Appearance End Revision History TablesIndex General Description OverviewRelated Information Connectivity Applicability Hardware OverviewPart Numbers User Interface IP Security Configuration and Program StorageSignaling Functional Summary Cross Connections Configuration ModelMonitoring Remote Data Centres Alarm Log7 M3UA Backhaul Operation 8 M2PA Longhaul Operation Default RoutingResilience IP Resilience Dual Resilient Configuration Dual Operation Specification Connecting a VT100 Terminal Installation and Initial ConfigurationInstallation Software Download Initial Configuration Configuration is displayed in the format shown below Telnet terminal displays the MML interface prompt Configuration Procedure Operation Log On/Off ProcedureGeneral Command Formats Command Character Set and SyntaxCommand Entry Command Responses Changing Configuration DataCommand Rejection Responses FTP Access Software Update from CD-ROM Software Backup to a Remote Data CentreSoftware Update from a Remote Data Centre Backing Up System Software Software Update from Startup Using a CD Software Update from StartupSoftware Update from Startup Using FTP Backing Up Configuration Data Configuration Update from CD ROM Updating Configuration DataConfiguration Update from a Remote Data Centre Configuration Update from Startup System Licenses Purchasing System Licenses Installing System Licenses License Update from Remote Data Centre License Update by FTP Parameter Table Parameter DefinitionsParameter Definitions Dbits Config License DuplexDate Dest Gateway FtppwdFtpser Hport LS2 PasswordLS1 Lssize PCR ResetPcmtype PER Halt Normal RestartSoft RKI Srtx AutoSpeed SS7MD Remote Operations Remote Operation Types MTP3 ITU Timers Signaling Gateway Timers Signaling Gateway-Specific TimersSignaling Gateway Specific Timers MTP3 Ansi Timers SCTP-Specific Timers Board Types Command Notation Command DefinitionsCommand Groups Command Attributes Alarm Commands Alcls Alarm Class Set Alclp Alarm Class Print Alfcp Alarm Fault Code Print Allip Alarm List Print Allop Alarm Log Print Diag CLA Occurred Cleared Title Alrei Alarm Reset Initiate Altei Alarm Test Initiate Altee Alarm Test End Configuration Commands Cnboi Configuration Board Initiate Cnboe Configuration Board End Cnbop Configuration Board Print Cnbui Configuration Back Up Initiate Cnmoi Configuration Monitor Initiate Cnmoe Configuration Monitor End Cnmop Configuration Monitor Print Cnpci Configuration PCM Initiate Cnpcc Configuration PCM Change Cnpce Configuration PCM End Cnpcp Configuration PCM Print Cnrdi Configuration Remote Data Centre Initiate Cnrdc Configuration Remote Data Centre Change Cnrde Configuration Remote Data Centre End Cnrdp Configuration Remote Data Centre Print Cnswp Configuration Software Print Cnsys Configuration System Set See .6.1, IP Port Bonding on page 142 for more information CNSYSSYSID=STATION1,PER=2,IPADDR=255.123.0.123 Cnsyp Configuration System Print Cntds Configuration Time and Date Set Cntdp Configuration Time And Date Print Cntos Configuration Timeout Value Set Cntop Configuration Timeout Value Print Cntsp Configuration Timeslot Print Cnupi Configuration Update Initiate Cnxci Configuration Cross Connect Initiate Cnxce Configuration Cross Connect End Cnxcp Configuration Cross Connect Print SS7 Signaling Commands 1 C7LSI CCS SS7 Link Set Initiate 2 C7LSC CCS SS7 Link Set Change 3 C7LSE CCS SS7 Link Set End 4 C7LSP CCS SS7 Link Set Print 5 C7RTI CCS SS7 Route Initiate 6 C7RTC CCS SS7 Route Change 7 C7RTE CCS SS7 Route End 8 C7RTP CCS SS7 Route Print 9 C7SLI CCS SS7 Signaling Link Initiate 10 C7SLC CCS SS7 Signaling Link Change 11 C7SLE CCS SS7 Signaling Link End 12 C7SLP CCS SS7 Signaling Link Print IP Commands Ipeps Set Ethernet Port Speed Ipepp Display Ethernet Port Speed Ipgwi Internet Protocol Gateway Initiate Ipgwe Internet Protocol Gateway End Ipgwp Internet Protocol Gateway Print MML Commands Mmloi MML Log Off Initiate Mmlop MML Log Off Print Mmlos MML Log Off Set Mmptc MML Port Change Mmptp MML Port Print Maintenance Commands Mnbli Maintenance Blocking Initiate Mnble Maintenance Blocking End Mnini Maintenance Inhibit Initiate Mnine Maintenance Inhibit End Mnrsi Maintenance Restart System Initiate Measurement Commands 10.1 MSC7P Measurements SS7 Print C7LINK Ossdur Msepp Measurement Ethernet Port Print ETH Mspcp Measurements PCM Print Msslp Measurements Sigtran Link Print Mssyp Measurements System Print Remote Data Centre Commands Rdcri Remote Data Centre Continuous Record Initiate Limitations Rdcrc Remote Data Centre Continuous Record Change Record must already be initiated Rdcre Remote Data Centre Continuous Record End Rdcrp Remote Data Centre Continuous Record Print Rdpdi Remote Data Centre Periodic Data Initiate Rdpde Remote Data Centre Periodic Data End Rdpdp Remote Data Centre Periodic Data Print Rdpri Remote Data Centre Periodic Report Initiate Rdprc Remote Data Centre Periodic Report Change Rdpre Remote Data Centre Periodic Report End Rdprp Remote Data Centre Periodic Report Print Signaling Gateway Commands Sgdpi Signaling Gateway Destination Point Initiate Sgdpc Signaling Gateway Destination Point Change Sgdpe Signaling Gateway Destination Point End Sgdpp Signaling Gateway Destination Point Print Sgiri Signaling Gateway Incoming Route Initiate Sgirc Signaling Gateway Incoming Route Change Sgire Signaling Gateway Incoming Route End Sgirp Signaling Gateway Incoming Route Print Sgrki Signaling Gateway Routing Key Initiate Sgrke Signaling Gateway Routing Key End Sgrkp Signaling Gateway Routing Key Print Sigtran Commands Snali Sigtran Application Server List Initiate Snale Sigtran Application Server List End Snalp Sigtran Application Server List Print Snapi Sigtran Application Server Initiate Snape Sigtran Application Server End Snapp Sigtran Application Server Print Snnai Sigtran Network Appearance Initiate Snnae Sigtran Network Appearance End Snnap Sigtran Network Appearance Print Snsli Sigtran Signaling Link Initiate Snlink Snslc Sigtran Signaling Link Change Snsle Sigtran Signaling Link End Snslp Sigtran Signaling Link Print Status Commands Stalp Status Alarm Print Stapp Status Application Server Print Stbop Status Board Print Stcrp Status C7 Route Print Possible Route Status values are Available Unavailable 14.5 STC7P Status C7 Link Print Stepp Status Ethernet Port Print Stipp Status IP Print Stpcp Status PCM Print Strdp Status Remote Data Centre Print Stslp Status Sigtran Link Print Stsyp Status System Print Configuration Overview Multiple IP Networks Signaling Configuration 1 SS7 Configuration Boards and PCMs SS7 MTP2 Operation SS7 M2PA Operation 2 M3UA Configuration M2PA Example Routing Configuration M3UA Backhaul Example Routing Configuration Example Routing MSUs Configuring Default RoutingManagement and Operations Route Set Test System Using Default Routing Resilience IP Port Bonding Dual Resilient Operation ConfigurationOverview of Dual Resilience 2.3 M2PA Inter Unit Signaling Links Example On Signaling Gateway 2, configure the link sets as follows Multihoming SIG CRT Alarm Fault Code ListingAlarm Fault Codes SYS MJR SYS PSU ID CRTAIS SYS CPU ID MJR SIGNone MJR Record SYS MJR SIG MJR SYS MRN Remote Data Centre Operation Ethernet Port Traffic Measurements Alarm Record File FormatSigtran Link Traffic Measurements System Measurements Ethernet Port Measurements File Format PCM Measurements File Format 4 SS7 Link Measurements File Format System Measurements File Format RDC Configuration and UsageSigtran Link Measurements File Format RDC Initialization SS7 Signaling Link Traffic Measurements Alarm DataPeriodic Reports Configuration Update Software UpdateConfiguration Backup Software Option Installation SS7G2x Snmp MIB From RFC1155-SMI OBJECT-TYPE = datakinetics Top level nodes within DK4032 MIB DkSysInfo Backhaul Configuration Worked Configuration Examples11.2 M2PA Longhaul Configuration SEP2 11.3.1 SG 1 Configuration 11.3.2 SG 2 Configuration Configuration Commands Command SummaryAlarm Commands CCS SS7 Signaling Commands Maintenance Commands IP CommandsMML Commands Measurement Commands Sigtran Commands Signaling Gateway CommandsStatus Commands Glossary ASP SEP Index CD-ROM Mnble Mnbli Mnine Mnini Sgdpe Sgdpi Sgdpp Sgirc Sgire Sgiri Sgirp Sgrke Sgrki