Fuji Bikes 5000G11S/P11S instruction manual Connecting the control terminals, Fwd

2-3-3 Connecting the control terminals

Table 2-3-3 lists the functions of the control circuit terminals. A control circuit terminal should be connected according to the setting of its functions.

Table 2-3-3

Classification	Terminal	Terminal name				Function
	symbol
	13	Potentiometer power		Used for +10V DC power supply for frequency setting POT (variable
		supply		resistor of 1 to 5kΩ)
	12	Voltage input		① Frequency is set according to the analog input voltage supplied from
					an external circuit.
					- 0 to +10V DC/0 to 100%
					- Reversible operation using positive and negative signals:0 to +/-
					10V DC/0 to 100%
					- Reverse operation: +10 to 0V DC/0 to 100%
				② The feedback signal for PID control is input.
				③ The analog input value from the external circuit is used for torque
					control. (P11S does not support this function.)
			*		Input resistance: 22kΩ
	V2	Voltage input	Frequency is set according to the analog input voltage supplied from an
Analog input				external circuit
					- 0 to +10V DC/0 to 100%
					- Reverse operation:+10 to 0V DC/0 to 100%
				* It can be used only one terminal "V2" or "C1" alternatively
			*		Input resistance:22kΩ
	C1	Current input		① Frequency is set according to the analog input current supplied from
					an external circuit.
					- 4 to 20mA DC/0 to 100%
					- Reverse operation:20 to 4mA DC/0 to 100%
				② The feedback signal for PID control is input.
				③ PTC thermistor input
				* It can be used only one terminal "V2" or "C1" alternatively.
			*		Input resistance:250Ω
	11	Analog input common	Common terminal for analog input signals
	FWD	Forward operation/stop		Used for forward operation (when FWD-CM is on) or deceleration and
		command		stop (when FWD-CM is off)
	REV	Reverse operation/stop		Used for reverse operation (when REV-CM is on) or deceleration and
		command		stop (when REV-CM is off)
	X1	Digital input 1		The coast-to-stop command, external alarm, alarm reset, multistep
	X2	Digital input 2		frequency selection, and other functions (from an external circuit) can be
	X3	Digital input 3		assigned to terminals X1 to X9. For details, see "Setting the Terminal
				Functions E01 to E09" in Section 5.2, "Details of Each Function."
	X4	Digital input 4
				<Specifications of digital input circuit>
	X5	Digital input 5
			*
	X6	Digital input 6
					Item		min.	typ.	max.
	X7	Digital input 7			Operating voltage	ON level	2V	-	2V
						OFF level	22V	24V	27V
	X8	Digital input 8
Digital input					Operating current at ON level		-	3.2mA	4.5mA
	X9	Digital input 9
					Allowable leakage current at OFF level		-	-	0.5mA
	CM	Common terminal	Common terminal for Digital input and FMP terminals
	P24	Control Unit power Supply	+24VDC power supply for control input. Maximum output current 100mA
	PLC	PLC signal power	Used to connect power supply for PLC output signals (rated voltage
				24(22 to 27) V DC) at source logic operation.
	FMA	Analog monitor	Outputs monitor signal using analog DC voltage 0 to +10V DC.
	(11:			The meaning of this signal is one of the following:
	Common			-Output frequency (before slip compensation) -Power consumption
	terminal)			-Output frequency (after slip compensation) -PID feedback value
Analog output				-Output current -PG feedback value
				-Output voltage -DC link circuit voltage
				-Output torque -Universal AO
				-Load factor
				*Connectable impedance:5kΩ minimum

2-13