Fuji Bikes 5000G11S/P11S H13 Auto-restart Restart time H18 Torque control, To 5.0 seconds

H13 Auto-restart (Restart time) H18 Torque control

‹Instantaneous switching to another power line (when the power of an operating motor is cut off or power failure occurs) creates a large phase difference between the line voltage and the voltage remaining in the motor, which may cause electrical or mechanical failure. To rapidly switch power lines, write the remaining voltage attenuation time to wait for the voltage remaining in the motor to attenuate. This function operates at restart after a momentary power failure.

H	3	R	E	S	T	A	R	T	T
Setting	range:			0.1 to 5.0 seconds

‹When the momentary power failure time is shorter than the wait time value, a restart occurs following the wait time. When the power failure time is longer than the wait time value, a restart occurs when the inverter is ready to operate (after about 0.2 to 0.5 second).

‹This	function controls motor torque according to a
command value.						Related functions
H 1	8	T R	Q	C T R	L	E01toE09
						(Set value: 23)

Set value Operation

0Inactive (Operation by frequency command)

1Torque control active

0 to +10V analog voltage input to terminal 12 and the direction of rotation (FWD or REV) is used for the torque command value. 0 is used for 0 to -10V.

2Torque control active

-10 to +10V analog voltage input to terminal 12 and the direction of rotation (FWD or REV) is used for the torque command value.

H14 Auto-restart (Freq. fall rate)

‹This function determines the reduction rate of the output frequency for synchronizing the inverter output frequency and the motor speed. This function is also used to reduce the frequency and thereby prevent stalling under a heavy load during normal operation.

H	4	F	A	L	L	R	A	T	E
Setting range:			0.00, 0.01 to 100.00 Hz/s

‹When 0.00 is set, the frequency is reduced according to the set deceleration time.

Note:

A too large frequency reduction rate is may temporarily increase the regeneration energy from the load and invoke the overvoltage protective function. Conversely, a rate that is too small extends the operation time of the current limiting function and may invoke the inverter overload protective function.

H15 Auto-restart (Holding DC voltage)

‹This function is for when 2 (deceleration-to-stop at power failure) or 3 (operation continuation) is set to "F14 Restart after momentary power failure (operation selection)." Either function starts a control operation if the main circuit DC voltage drops below the set operation continuation level.

	H	5	H	O		L	D	V
Setting range			230		V series:			200 to 300V
			460		V series:			400 to 600V

‹When power supply voltage to the inverter is high, control can be stabilized even under an excessive load by raising the operation continuation level. However, when the level is too high, this function activates during normal operation and causes unexpected motion. Please contact Fuji electric when changing the initial

value.
H16	Auto-restart (OPR command selfhold time)

‹As the power to an external operation circuit (relay sequence) and the main power to the inverter is generally cut off at a power failure, the operation command issued to the inverter is also cut off. This function sets the time an operation command is to be held in the inverter. If a power failure lasts beyond the self-hold time, power-off is assumed, automatic restart mode is released, and the inverter starts operation at normal mode when power is applied again. (This time can be considered the allowable power failure time.)

H 6 S E L F H O L D T

Setting range: 0.0 to 30.0 seconds, 999

When "999" is set, an operation command is held (i.e., considered a momentary power failure) while control power in the inverter is being established or until the main circuit DC voltage is about 100Vdc.

T o rq u e co n tro l b lo ck d ia g ra m

			T o rq u e c o m m a n d va lue
					+
V o ltag e a t		x		T o rq u e				R e g u la to r	O u tp u t
te rm in a l 1 2				lim ita tio n		-			fre q u e n c y
	F orw a rd c o m m a n d				D e te c te d to rqu e
	R e ve rs e c om m a n d						c u rre n t

The torque command value is +200% when the voltage at terminal 12 is +10V and is -200% when the voltage is -10V. ‹Auto tuning(P04/A13: 2) should be done to use this

function.

‹In torque control, the torque command value and motor load determine the speed and direction of rotation.

‹When the torque is controlled, the upper limit of frequency refers to the minimum value among the maximum frequency , the frequency limiter (upper limiter) value, and 120 Hz. Maintain the frequency at least one-tenth of the base frequency because torque control performance deteriorates at lower frequencies.

‹If the operation command goes off during a torque control operation, the operation is switched to speed control and the motor decelerates-to-stop. At this time, the torque control function does not operate.

‹This function cannot be used when the motor 2 is selected.

‹This function cannot be used for FRN-P11S.

The malfunction may be occurred when the set torque is mistaken. (up WARNING to upper frequency, maximum

frequency or 120Hz)

as accident may result.

H19 Active drive

‹This function automatically extends accelerating time against acceleration operation of 60 seconds or longer to prevent an inverter trip resulting from a temperature rise in inverter due to overcurrent.

H 1 9 A U T R E D

Set value 0: Inactive

1:Active

(When the active drive function is activated, the acceleration time is three times the selected time.)

5-37