Fuji Bikes 5000G11S/P11S instruction manual PMotor Parameters, HHigh Performance Functions

Func

NAME

LCD Display

Setting range

Unit

Min.

Factory setting

Change

User

Remark

No.

Unit

during op

Set value

-30HP

40HP-

C20

JOG frequency

C20

JOG Hz

G11S:0.00 to 400.00Hz

Hz

0.01

5.00

A

P11S:0.00 to 120.00Hz

C21

PATTERN(Mode select)

PATTERN

0,1,2

-

-

0

NA

operation

C22

(Stage 1)

C22

STAGE 1

Operation time:0.00 to 6000s

s

0.01

0.00

F1

A

C23

(Stage 2)

C23

STAGE 2

F1 to F4 and R1 to R4

0.00

F1

A

C24

(Stage 3)

C24

STAGE 3

0.00

F1

A

C25

(Stage 4)

C25

STAGE 4

0.00

F1

A

C26

(Stage 5)

C26

STAGE 5

0.00

F1

A

C27

(Stage 6)

C27

STAGE 6

0.00

F1

A

C28

(Stage 7)

C28

STAGE 7

0.00

F1

A

C30

Frequency command 2

C30

FREQ CMD 2

0 to 11

-

-

2

NA

C31

Offset adjust(terminal[12])

C31

BIAS 12

-100.0 to +100.0%

%

0.1

0.0

A

C32

C32

GAIN 12

0.0 to +200.0%

%

0.1

100.0

A

C33

Analog setting signal filter

C33

REF FILTER

0.00 to 5.00s

s

0.01

0.05

A

P:Motor Parameters
P01	Number of motor 1 poles	P01	M1 POLES	2 to 14	-	2	4	NA
P02	Motor 1	(Capacity) P02	M1-CAP	Up to 30[HP]: 0.01 to 60HP	HP	0.01	Motor Capacity	NA
				40[HP]and above: 0.01 to 800HP
P03		(Rated current) P03	M1-Ir	0.00 to 2000A	A	0.01	Motor rated current	NA
P04		(Tuning) P04	M1 TUN1	0, 1, 2	-	-	0	NA
P05		(On-line Tuning) P05	M1 TUN2	0, 1	-	-	0	NA
P06		(No-load current) P06	M1-Io	0.00 to 2000A	A	0.01	Fuji STANDARD RATED	NA
							VALUE
P07		(%R1 setting) P07	M1-%R1	0.00 to 50.00%	%	0.01	Fuji STANDARD RATED	A
							VALUE
P08		(%X setting) P08	M1-%X	0.00 to 50.00%	%	0.01	Fuji STANDARD RATED	A
							VALUE
P09	Slip compensation control 1	P09	SLIP COMP1	0.00 to 15.00Hz	Hz	0.01	0.00	A
H:High Performance Functions
H03	Data initializing	H03	DATA INIT	0, 1	-	-	0	NA
H04	Auto-reset	(Times) H04	AUTO-RESET	0, 1 to 10 times	-	1	0	A
H05		(Reset interval) H05	RESET INT	2 to 20s	s	1	5	A
H06	Fan stop operation	H06	FAN STOP	0, 1	-	-	0	A
H07	ACC/DEC pattern	(Mode select) H07	ACC PTN	0,1,2,3	-	-	0	NA
H08	Rev. phase sequence lock	H08	REV LOCK	0, 1	-	-	0	NA
H09	Start mode	H09	START MODE	0, 1, 2	-	-	0	NA
H10	Energy-saving operation	H10	ENERGY SAV	0, 1	-	-	G11S:0	A
							P11S:1
H11	DEC mode	H11	DEC MODE	0, 1	-	-	0	A
H12	Instantaneous OC limiting	H12	INST CL	0, 1	-	-	1	NA
H13	Auto-restart	(Restart time) H13	RESTART t	0.1 to 10.0s	s	0.1	0.1	NA
H14		(Freq. fall rate) H14	FALL RATE	0.00 to 100.00Hz/s	Hz/s	0.01	10.00	A
H15		(Holding DC voltage) H15	HOLD V	3ph 230V class: 200 to 300V	V	1	230V class:235V	A
				3ph 460V class: 400 to 600V			460V class:470V
H16	(OPR command selfhold time) H16		SELFHOLD t	0.0 to 30.0s, 999	s	0.1	999	NA
H18	Torque control	H18	TRQ CTRL	G11:0, 1, 2, P11:0	-	-	0	NA
H19	Active drive	H19	AUT RED	0, 1	-	-	0	A
H20	PID control	(Mode select) H20	PID MODE	0, 1, 2	-	-	0	NA
H21		(Feedback signal) H21	FB SIGNAL	0, 1, 2, 3	-	-	1	NA
H22		(P-gain) H22	P-GAIN	0.01 to 10.00 times	-	0.01	0.1	A
H23		(I-gain) H23	I-GAIN	0.0 , 0.1 to 3600s	s	0.1	0.0	A
H24		(D-gain) H24	D-GAIN	0.00s , 0.01 to 10.0s	s	0.01	0.00	A
H25		(Feedback filter)	FB FILTER	0.0 to 60.0s	s	0.1	0.5	A
H26	PTC thermistor	(Mode select) H26	PTC MODE	0, 1			0	A
H27		(Level) H27	PTC LEVEL	0.00 to 5.00V	V	0.01	1.60	A
H28	Droop operation	H28	DROOP	G11:-9.9 to 0.0Hz, P11:0.0 (Fixed.)	Hz	0.1	0.0	A
H30	Serial link	(Function select) H30	LINK FUNC	0, 1, 2, 3	-	-	0	A
H31	Modbus-RTU	(Address)	ADDRESS	0 (broadcast), 1 to 247	-	1	1	NA
H32	(Mode select on no response error)		MODE ON ER	0, 1, 2, 3	-	-	0	A
H33		(Timer)	TIMER	0.0 to 60.0s	s	0.1	2.0	A
H34		(Baud rate)	BAUD RATE	0, 1, 2, 3	-	-	1	A
H35		(Data length)	LENGTH	0 (8-bit fixed)	-	-	0	A
H36		(Parity check)	PARITY	0, 1, 2	-	-	0	A
H37		(Stop bits)	STOP BITS	0(2bit), 1(1bit)	-	-	0	A
H38	(No response error detection time)		NO RES t	0 (No detection), 1 to 60s	s	1	0	A
H39		(Response interval)	INTERVAL	0.00 to 1.00s	s	0.01	0.01	A

5-3