Fuji Bikes 5000G11S/P11S E45 LCD monitor function, Display item, Set value, E46Language

E43	LED monitor (function)
E44	LED monitor (display at stop mode)

‹The data during inverter operation, during stopping, at frequency setting, and at PID setting is displayed on the LED.

‹Display during running and stopping

During running, the items selected in "E43 LED monitor (display selection)," are displayed. In "E44 LED monitor (display at stopping)," specify whether to display some items out of the set values or whether to display the same items as during running.

E45 LCD monitor (function)

‹This function selects the item to be displayed on the LCD monitor in the operation mode.

	E	4	5	L	C	D	M	N	T	R
							Display item
Set value

0Operation status, rotating direction, operation guide

1Output frequency (before slip compensation), output current, calculated torque value in bar graph

E

4

3

L

E

D

M

N

T

R

E

4

4

L

E

D

M

N

T

R

2

Value

E44＝0

E44＝1

set to

At stopping

During

At

During

E43

running

stopping

running

0

Set frequency value

Output frequency

(Hz)

(before slip compensation) (Hz)

1

Set frequency value

Output frequency

(Hz)

(after slip compensation) (Hz)

2

Set frequency value (Hz)

Set value: 0 During running

60.00

RUNFWD

PRG⇒PRG MENU F/D⇒LED SHIFT

Set value: 1

When stopping

60.00

STOP

PRG⇒PRG MENU F/D⇒LED SHIFT

3	Output current (A)
4	Output voltage (command value) (V)
5	Synchronous speed				Synchronous speed (r/min)
	set value (r/min)
6	Line	speed	set		Line speed (m/min.)
	value (m/min.)
7	Load	speed	set		Load speed (r/min)
	value (r/min)
8	Calculated torque value				(%)
9	Output power (HP)
10	PID target value 1			(direct input from keypad panel)
11	PID target value 2			(input from "F02 Frequency 1")
12	PID feedback amount

Note: For the values 10 to 12 set to E43, the data is displayed only when selected in "H20 PID control (operation selection)."

‹Display at frequency setting

When a set frequency is checked or changed by the keypad panel, the set value shown below is displayed. Select the display item by using "E43 LED monitor (display selection)." This display is not affected by "E44 LED monitor (display at stopping)."

Value set to	Frequency setting
E43
0,1,2,3,4	Set value of frequency (Hz)
5	Set value of synchronous speed (r/min)
6	Set value of line speed (m/min.)
7	Set value of load speed (r/min)
8,9	Set value of frequency (Hz)
10,11,12	Set value of frequency (Hz)

Note: For the values 10 to 12 set to E43, the data is displayed only when selected in "H20 PID control (operation selection)."

60.00

Hz

A

%

Fout/Iout/TRQ

Full-scale value of bar graph

Display item	Full-scale
Output frequency	Maximum frequency
Output current	200% of inverter rated value
Calculated torque value	200% of motor rated value

Note: The scale cannot be adjusted.

E46Language

‹This function selects the language for data display on the LCD monitor.

4 6 L A N G U A G E

Set value	Language	Set value	Language
	displayed		displayed
0	Japanese	3	French
1	English	4	Spanish
2	German	5	Italian

Note: English language is used for all LCD screens in this manual. For other languages, refer to the relevant instruction manual.

E47 LCD monitor (contrast)

‹This function adjusts the LCD contrast. Increase the set value to raise contrast and decrease to lower contrast.

E 4 7 C O N T R A S T

Set value	0,1,2 • • • • • • 8,9,10
Screen	Low	High

5-27