Fuji Bikes 5000G11S/P11S instruction manual ‹Setting example 100 F

C20 JOG frequency

‹This function sets the frequency for jogging operation of motor, which is different from the normal operation.

	C	2	0	J		O	G	H	z
Setting range					G11S : 0.00 to 400.00 Hz
					P11S : 0.00 to 120.00 Hz

‹Starting with the jogging frequency is combined with jogging select signal input from the keypad panel or control terminal. For details, see the explanations of "E01 Terminal X1" to "E09 Terminal X9."

C21 Pattern operation (mode select)

‹Pattern operation is an automatic operation according to preset operation time, direction of rotation, acceleration and deceleration time, and frequency.

When using this function, set 10 (pattern operation) to "F01 Frequency setting."

The following operation patterns can be selected.

C22	Pattern operation (stage 1)
～	～
C28	Pattern operation (stage 7)

‹Seven stages are operated in order (of function codes) according to the values set in "C22 Pattern operation (stage 1)" to "C28 Pattern operation (stage 7)." Each function sets the operation time and the rotating direction for each stage and assigns set values of the acceleration and deceleration time.

C	2	2	S	T	A	G	E	1
C	2	3	S	T	A	G	E	2
C	2	4	S	T	A	G	E	3
C	2	5	S	T	A	G	E	4
C	2	6	S	T	A	G	E	5
C	2	7	S	T	A	G	E	6
C	2	8	S	T	A	G	E	7

											Related functions
	C	2	1	P	A	T	T	E	R	N	F01, C30
											(Set value:10)
Set value								Operation pattern

0	Perform a pattern operation cycle, then stop operation.
1	Perform	pattern operation repeatedly. Stop operation
	using a stop command.
2	Perform	a pattern operation cycle, then continue
	operation with the last frequency set.

Set or

assign item Operation time

Rotation direction Acceleration and deceleration time

Value range

0．00 to 6000s

F: Forward (counterclockwise)

R: Reverse (clockwise)

1:Acceleration time 1 (F07), deceleration time 1 (F08)

2:Acceleration time 2 (E10), deceleration time 2 (E11)

3:Acceleration time 3 (E12), deceleration time 3 (E13)

4:Acceleration time 4 (E14), deceleration time 4 (E15)

Note: The operation time is represented by the three most significant digits, hence, can be set with only three

Set value:0
Forward	FWD

Output frequency 0

Reverse

Set value:1
Forward	FWD

Output frequency 0

Reverse

End of a cycle

Time

End of a cycle

Time

high-order digits.

‹Setting example 100 F 3

Acceleration and deceleration time (code): 3

Motor rotating direction:

Forward (counterclockwise)

Operation time: 100s

Set the operation time to 0.00 for stages not used, which are skipped in operation.

Set value:2			End of a cycle
		FWD
Forward
Output
frequency	0		Time
Reverse

With regard to the set frequency value, the multistep frequency function is assigned as listed in the table below. Set frequencies to "C05 Multistep frequency 1," to "C11 Multistep frequency 7."

Stage No.	Operation frequency to be set
Stage 1	Multistep frequency 1 (C05)
Stage 2	Multistep frequency 2 (C06)
Stage 3	Multistep frequency 3 (C07)
Stage 4	Multistep frequency 4 (C08)
Stage 5	Multistep frequency 5 (C09)
Stage 6	Multistep frequency 6 (C10)
Stage 7	Multistep frequency 7 (C11)

5-29