Fuji Bikes 5000G11S/P11S Setting range 0.0 to 60.0Hz, F26 Motor sound carrier frequency, F30, F31

F23	Starting frequency	(frequency)
F24	Start frequency	(Holding time)
F25	Stop frequency

The starting frequency can be set to reserve the torque at startup and can be sustained until the magnetic flux of the motor is being established.

‹Frequency: This function sets the frequency at startup.

F 2 3 S T A R T H z

Setting range: 0.1 to 60Hz

‹Holding time: This function sets the holding time during which the start frequency is sustained at startup.

F 2 4 H O L D I N G t

Set values: 0.1 to 10.0 seconds

∗The holding time does not apply at the time of switching between forward and reverse.

∗The holding time is not included in the acceleration time.

∗The holding time also applies when pattern operation (C21) is selected. The holding time is included in the timer value.

‹This function sets the frequency at stop.

	F	2	5	S	T	O	P	H		z
Setting range: 0.0 to 60.0Hz
	Output frequency
									Forward rotation
						Holding time
	Starting frequency
	Stopping frequency

Time

The operation does not start when the starting frequency is less than the stopping frequency or when the setting frequency is less than the stopping frequency.

F26 Motor sound (carrier frequency)

‹This function adjusts the carrier frequency, correct adjustment of which prevents resonance with the machine system, reduces motor and inverter noise, and also reduces leakage current from output circuit wiring.

F

2

6

M

T

R

S

O

U

N

D

Nominal applied motor

Setting range

G11

75HP or less

0.75 to 15kHz

100HP or more

0.75 to 10kHz

P11

30HP or less

0.75 to 15kHz

40HP to 100HP

0.75 to 10kHz

125HP or more

0.75 to 6kHz

Carrier frequency

Low

High

Motor noise

High

Low

Output current waveform

Bad

Good

Leakage current

Small amount

Large amount

Noise occurrence

Extremely low

High

Notes:

1.Reducing the set value adversely affects the output current waveform (i.e., higher harmonics), increases motor loss, and raises motor temperature. For example, at 0.75kHz, reduce the motor torque by about15%.

2 Increasing the set value increases inverter loss and raises

inverter temperature. 5-15

F27 Motor sound (sound tone)

‹The tone of motor noise can be altered when the carrier frequency is 7kHz or lower. Use this function as required.

	F	2	7	M	T	R		T	O	N	E
Setting range:				0 , 1, 2 , 3
F30					FMA		(voltage adjust)
F31					FMA		(function)

Monitor data (e.g.,output frequency, output current) can be output to terminal FMA as a DC voltage. The amplitude of the output can also be adjusted.

‹This function adjusts the voltage value of the monitor item selected in F31 when the monitor amount is 100%. A value from 0 to 200 (%) can be set in 1% steps.

F

3

0

F

M

A

V

-

A

D

J

Setting range: 0 to 200%

Higher than 10V

F30:200%

output

10V

F30:100%

FMAterminal voltage

5V

F30:0%

F30:50%

50% 100%

‹This function selects the monitor item to be output to terminal FMA.

	F	3	1	F	M	A	F	U		N	C
Set				Monitor item
									Definition of 100% monitor amount
value

0Output frequency 1 Maximum output frequency (before slip compensation)

1Output frequency 2 Maximum output frequency (after slip compensation)

2	Output current	Rated	output	current		of
3	Output voltage	inverter x 2
		230V series: 250V
4	Output torque	460V series: 500V
		Rated torque of motor x 2
5	Load rate	Rated load of motor x 2
6	Power consumption	Rated output of inverter x 2
7	PID feedback amount	Feedback amount of 100%
8	PG feedback amount	Synchronous		speed		at
	(only when option is installed)	maximum frequency
9	DC link circuit voltage
		230V series: 500V
10	Universal AO	460V series: 1,000V
		0 to	10V output		through
		communication and not related to
		inverter operation.

※The power consumption shows "0" during regenerative load.