Fuji Bikes 5000G11S/P11S C30 Frequency command, Related functions E01 to E09 Set value11 F01

‹Pattern operation setting example
	Function		Set value	Operation frequency to be set
C21 (operation selection)			1				-
	C22 (stage 1)		60.0F2 Multistep frequency 1 (C05)
	C23 (stage 2)		100F1 Multistep frequency 2 (C06)
	C24 (stage 3)		65.5R4 Multistep frequency 3 (C07)
	C25 (stage 4)		55.0R3 Multistep frequency 4 (C08)
	C26 (stage 5)		50.0F2 Multistep frequency 5 (C09)
	C27 (stage 6)		72.0F4 Multistep frequency 6 (C10)
	C28 (stage 7)		35.0F2 Multistep frequency 7 (C11)
The following diagram shows this operation.
Forward		Multistep		Multistep				Multistep
direction				frequency 6				frequency 7
	Multistepfrequency 2				ACC4			(Stage 7)
speed)	frequency 1		Multistep
	(Stage 1)
			frequency 5
	FWD
frequency(motor				ACC2					DEC1
						DEC2
		ACC1	DEC4
	ACC2	ACC4	ACC3				DEC2		Time

Output
			Multistep
						Multistep
			frequency 3
						frequency 4
Reverse
					55.0S 50.0S
	60.0S	100S		65.5S			72.0S	35.0S
direction

C30 Frequency command 2

‹This function selects the frequency setting method.

Related functions

E01 to E09

(Set value:11)

F01

C 3 0 F R E Q C M D 2

For the setting method, see the explanation for F01.

C31 Bias (terminal[12])

C32Gain (terminal[12])

‹This function sets the Gain and Bias of the analog input (terminals [12] ).

	C	3	1	B	I	A	S		1	2
	C	3	2	G	A	I	N		1	2
The setting range :
BIAS: -100 to +100%
GAIN:0.0 to 200%
	Terminal										Reference
					Gain			Bias
12											voltage

Set

value 0.1S :16

Output value of Gain 12

200%

Set

Output signals from terminals Y1 to Y5

100%

value0.1S :17

+10V

50%

‹Running and stopping are controlled by pressing the FWD
and STOP	keys and by opening and closing the control					-10	0	+10[V] Analog input voltage
terminals.					FWD key		-10V	[terminal 12]
When using the keypad panel, pressing the
starts operation.		Pressing the	STOP key pauses stage
advance. Pressing the FWD key again restarts operation
from the stop point according to the stages. If an alarm
stop occurs, press the RESET			key to release operation
of the inverter protective function, then press the					FWD
key to restart stage advance.							Output value of Bias 12
If required to start operation from the first stage "C22								Bias setting
Pattern operation (stage 1)," enter a stop command and							+10V	(when positive)
press the	RESET	key.
If an alarm stop occurs, press the RESET				key to release			(+100%)
the protective function, then press the key again.

Notes:
1. The direction of rotation cannot be reversed by a
			-10	0		+10[V]
command issued from the	REV	key on the keypad panel
		rotation commands entered
or terminal [REV]. Any reverse					Output value of Gain 12
are canceled. Select forward or reverse rotation by the data
						Bias setting
in each stage. When the control terminals are used for
operation, the self-hold function of operation command also					-10V	(when negative)
does not work. Select an alternate type switch when using.				(-100%)

2.At the end of a cycle, the motor decelerates-to-stop according to the value set to "F08 Deceleration time 1."

5-30