Fuji Bikes 5000G11S/P11S Torque limit Related function F41 Value selected F40, On →off

Function selected

Inhibit data changes. Allow data changes.

Torque limit 2/torque limit 1 [TL2/TL1]

This function switches the torque limit value set in function codes F40 and F41, and E16 and E17 by an external digital input signal.

	Set value input signal
		Torque limit	Related function
14			～	F41
		value selected	F40
			E16～E17
	off	F40 DRV TRQ1	Setting range
		F41 BRK TRQ1
			DRV 20 to 200% ,999
	on	E16 DRV TRQ2	BRK 0, 20 to 200% ,999
		E17 BRK TRQ2

Switching operation between line and inverter (50Hz) [SW50]

Motor operation can be switched from 50Hz commercial power operation to inverter operation without stopping the motor by switching the external digital input signal.

Set value
input signal	Function
15
off→on	Inverter operation to line operation (50Hz)
on→off	Line operation to inverter operation (50Hz)

Switching operation between line and inverter (60Hz) [SW60]

Motor operation can be switched from 60Hz commercial power operation to inverter operation without stopping the motor by switching the external digital input signal.

Set value
input signal	Function
16
off→on	Inverter operation to line operation (60Hz)
on→off	Line operation to inverter operation (60Hz)

‹When the digital input signal goes off, 50 or 60 Hz is output according to the set value input signal after the restart waiting time following a momentary power failure (function code H13). The motor is then directed to inverter operation.

WARNING

-After the LU(Low Voltage) trip is occurred and reset it, the inverter will automatically restart because the operation command is kept by internal sequence.

Accident may result.

UP command [UP]/DOWN command [DOWN]

When an operation command is input (on), the output frequency can be increased or decreased by an external digital input signal.

The change ranges from 0 to maximum frequency. Operation in the opposite direction of the operation command is not allowed.

Related function	Related function
F01, C30	E01～E09
	(set value: 11, 35)

	Combination of set					Function selected
	value input signals					(when operation command is on)
18			17
	off			off		Holds the output frequency.
	off			on		Increases	the	output	frequency
						according to the acceleration time.
	on			off		Decreases	the	output	frequency
						according to the deceleration time.
						Holds the output frequency.
There are			the two		types of UP/DOWN operations as
shown		below. Set				the desired type		by setting the

frequency (F01 or C30).

‹The data "8: UP/DOWN 1" is valid only when the Motor

2 is selected.
Frequency	Initial value	Operation command reentry
setting	at power
		during deceleration
(F01 or C30)	input on
		Operates at the frequency at reentry.
8		Frequency
	0Hz
(UP/DOWN1)		FWD	ON
		(REV)		OFF
		Returns to the frequency before
		deceleration
9	Previous	Frequency
(UP/DOWN2)	frequency	FWD	ON
		(REV)		OFF

Write enable for KEYPAD [WE-KP]

This function allows the data to be changed only when an external signal is being input, thereby making it difficult to change the data.

19

off

Note:

If a terminal is set to value 19, the data becomes unable to be changed. To change the data, turn on the terminal and change the terminal setting to another number.

PID control cancel [Hz/PID]

The PID control can be disabled by an external digital input signal.

	Set value	Function selected	Related function
	input signal		H20	～	H25
20
	off	Enable PID control.
	on	Disable PID control
		(frequency setting from keypad panel).

5-20