Fuji Bikes 5000G11S/P11S Frequency selected, E01 X1 Terminal function E09 X9 Terminal function

E:Extension Terminal Functions

E01	X1 Terminal function
～	～
E09	X9 Terminal function

‹Each function of digital input terminals X1 to X9 can be set as codes.

	E	0	1	X	1	F	U	N	C
	E	0	2	X	2	F	U	N	C
	E	0	3	X	3	F	U	N	C
	E	0	4	X	4	F	U	N	C
	E	0	5	X	5	F	U	N	C
	E	0	6	X	6	F	U	N	C
	E	0	7	X	7	F	U	N	C
	E	0	8	X	8	F	U	N	C
	E	0	9	X	9	F	U	N	C
Set value							Function
0,1,2,3		Multistep frequency selection (1 to 15 steps) [SS1],[SS2],[SS4],[SS8]
4,5		Acceleration and deceleration time selection (3 steps) [RT1],[RT2]
6		Self-hold selection [HLD]
7		Coast-to-stop command [BX]
8		Alarm reset [RST]
9		External alarm [THR]
10		Jogging [JOG]
11		Frequency setting 2/frequency setting 1 [Hz2/Hz1]
12		Motor 2/motor 1 [M2/M1]
13		DC injection brake command [DCBRK]
14		Torque limit 2/torque limit 1 [TL2/TL1]
15		Switching operation from line to inverter (50Hz) [SW50]
16		Switching operation from line to inverter (60Hz) [SW60]
17		UP command [UP]
18		DOWN command [DOWN]
19		Edit permission command (data change permission) [WE-KP]
20		PID control cancellation [Hz/PID]
21		Forward/inverse switching (terminals 12 and C1) [IVS]
22		Interlock (52-2) [IL]
23		Torque control cancellation [Hz/TRQ]
24		Link operation selection (Standard:RS-485, Option: BUS) [LE]
25		Universal DI [U-DI]
26		Start characteristics selection [STM]
27		PG-SY enable ( Option ) [PG/Hz]
28		Synchronization command ( Option ) [SYC]
29		Zero speed command with PG option [ZERO]
30		Forced stop command [STOP1]
31		Forced stop command with Deceleration time 4 [STOP2]
32		Pre-exiting command with PG option [EXITE]
33		Line speed control Cancellation [Hz/LSC]
34		Line speed frequency memory [LSC-HLD]
35		Frequency setting 1 / Frequency setting 2 [Hz1/Hz2]

Note: Data numbers which are not set in the functions from E01 to E09, are assumed to be inactive.

Multistep frequency selection [SS1][SS2][SS4][SS8]

The frequency can be switched to a preset frequency in function codes C05 to C19 by switching the external digital input signal. Assign values 0 to 3 to the target digital input terminal. The combination of input signals determines the frequency.

Combination of			set
value input signals				Frequency selected
3	2	1	0
[SS8]	[SS4]	[SS2]	[SS1]
off	off	off	off	Assigned by F01 or C30
off	off	off	off	C05 MULTI Hz-1
off	off			C06 MULTI Hz-2
off	off			C07 MULTI Hz-3		Related function
						C05 to C19
off		off	off	C08 MULTI Hz-4
off		off	off	C09 MULTI Hz-5
off				C10 MULTI Hz-6	Setting range
off				C11 MULTI Hz-7
	off	off	off	C12 MULTI Hz-8	G11S:0.00 to 400.00Hz
	off	off	off	C13 MULTI Hz-9	P11S:0.00 to 120.00Hz
	off			C14 MULTI Hz-10
	off	off	off	C15 MULTI Hz-11
				C16 MULTI Hz-12
		off	off	C17 MULTI Hz-13
				C18 MULTI Hz-14
				C19 MULTI Hz-15

Acceleration and deceleration time selection [RT1][RT2]

The acceleration and deceleration time can be switched to a preset time in function codes E10 to E15 by switching the external digital input signal. Assign values 4 and 5 to the target digital input terminal. The combination of input signals determines the acceleration and deceleration times.

Combination of
set value	input
signals	Acceleration and deceleration times selected

54

[RT2] [RT1]

off	off	F07 ACC TIME1	Setting range
		F08 DEC TIME1
			0.01 to 3600s
off	on	E10 ACC TIME2
		E11 DEC TIME2	Related function
			F07～F08
on	off	E12 ACC TIME3
			E10～E15
		E13 DEC TIME3
on	on	E14 ACC TIME4
		E15 DEC TIME4
3-wire operation stop command [HLD]

This selection is used for 3-wire operation. The FWD or REV signal is self-held when [HLD] is on, and the self-hold is cleared when [HLD] is turned off. To use this [HLD] terminal function, assign 6 to the target digital input terminal.

Output frequency		Forward
		rotation		Reverse
				rotation
FW D			Ignore
	ON		d			ON
REV
			ON	ON
HLD
		ON			ON

5-18