Fuji Bikes 5000G11S/P11S instruction manual Three-phase 460V series

(2) Three-phase 460V series

Nominal applied		0.5		1	2	3	5	7.5	10		15	20	25	30	40	50	60	75	100	125	150	200	250	300	350	400	450	500	600	700	800
motor [HP]
	Type	F50		001	002	003	005	007	010		015	020	025	030	040	050	060	075	100	125	150	200	250	300	350	400	450	500	600	-	-
	FRN[][][]G11S-4UX
	Rated output	1.2		2.0	2.9	4.4	7.2	10	14		19	24	31	36	48	60	73	89	120	140	167	202	242	300	331	414	466	518	590	-	-
	capacity (*1) [kVA]
	Rated output	1.5		2.5	3.7	5.5	9	13	18		24	30	39	45	60	75	91	112	150	176	210	253	304	377	415	520	585	650	740	-	-
	current (*2) [A]
	Overload	150% of rated output current for 1 min.													150% of rated output current for 1 min.
G11	capability	200% of rated output current for 0.5 s													180% of rated output current for 0.5 s
	Starting torque	200% or more (under torque vector control)													180% or more (under torque vector control)
	Braking torque	50%ormore				100% or more					20% or more											10 to 15%
	(*3) [%]
	Braking time [s]		5				5													No limit
	Braking duty	5		3	5	3	2	3		2										No limit
	cycle [%ED]
	Mass [lbs (kg)]	4.9		5.5	8.4	8.4	8.4	14		14	22	22	23	23	64	75	86	88	106	154	154	220	220	309	309	705	705	904	904	-	-
		(2.2)		(2.5)	(3.8)	(3.8)	(3.8)	(6.5)		(6.5)	(10)	(10)	(10.5)	(10.5)	(29)	(34)	(39)	(40)	(48)	(70)	(70)	(100)	(100)	(140)	(140)	(320)	(320)	(410)	(410)
	Type	-		-	-	-	-	007		010	015	020	025	030	040	050	060	075	100	125	150	200	250	300	350	400	450	500	600	700	800
	FRN[][][]P11S-4UX
	Rated capacity (*1)	-		-	-	-	-	10		13	18	24	29	35	48	60	73	89	120	140	167	202	242	300	331	386	414	518	590	669	765
	[kVA]
	Rated output	-		-	-	-	-	12.5		16.5	23	30	37	44	60	75	91	112	150	176	210	253	304	377	415	485	520	650	740	840	960
	current (*2) [A]
	Overload	110% of rated output current for 1 min.
P11	capability
	Starting torque															50% or more
	Braking torque						Approx. 20%														Approx. 10 to 15%
	(*3) [%]
	Braking time [s]																No limit
	Braking duty																No limit
	cycle [%ED]
	Mass [lbs (kg)]	-		-	-	-	-	13		13	13	22	22	23	64	64	75	86	88	106	154	154	220	220	309	309	309	705	705	904	904
								(6.1)		(6.1)	(6.1)	(10)	(10)	(10.5)	(29)	(29)	(34)	(39)	(40)	(48)	(70)	(70)	(100)	(100)	(140)	(140)	(140)	(320)	(320)	(410)	(410)
Output ratings	Rated output	3-phase, 380V, 400V, 415V(440V)/50Hz, 380V, 400V, 440V, 460V/60Hz
	Rated output	50,60Hz
	voltage(*4) [V]
	frequency [Hz]
	Phases, voltage,	3-phase,380 to 480V,50/60Hz													3-phase, 380 to 440V/50Hz							*5)
	frequency														3-phase, 380 to 480V/60Hz
ratings	Voltage/frequency	Voltage: +10% to -15% (Imbalance rate between phases: 2% or less (*6) , Frequency: +5% to -5%
	variations
Input	Momentary voltage	Operation will continue with 310V or more. If voltage drops below 310V, operation will continue for up to 15 ms.
	dip capability (*7)	If "Continuous operation" is selected, the output frequency will be lowered to withstand the load until normal voltage is resumed.
	Required power
	supply	0.7		1.2	2.2	3.1	5.0	7.2		9.7	15	20	24	29	38	47	57	70	93	111	136	161	196	244	267	341	383	433	488	549	610
	capacity (*8)[kVA]

(*1) Indicated capacities are at the rated output voltage 230V for the 230V series and 460V for the 460V series. The rated capacity will be lowered if the supply voltage is lowered.

(*2) In the case of a low impedance load, such as a high-frequency motor, the current may drop below the rated current.

(*3) Indicates when a nominal applied motor is used (the average torque when decelerated to stoppage from 60 Hz, which varies depending on motor loss).

(*4) An output voltage exceeding the supply voltage cannot be generated.

(*5) The taps within the inverter must be changed for a power supply rated at 380 to 398V/50 Hz or 380 to 430V/60 Hz.

(*6) If the imbalance between phases exceeds 2%, use a power-factor correcting DC reactor (DCR).

Imbalance rate between phases [%] = ( Max. Voltage [V] - Min. Voltage [V] ) x 67[%] 3-phase average voltage [V]

(*7) Test was conducted under the standard load conditions stipulated by the JEMA committee (at the load equivalent to 85% of the nominal applied motor).

(*8) Indicates the values required when using a power-factor correcting DC reactor (DCR) (optional for inverters of 75HP or less) with a loaded nominal applied motor.

9-2