Fuji Bikes 5000G11S/P11S Inverter Function Code Access, Command and Monitor Data Registers

9-4-5 Inverter Function Code Access

All of the inverter function codes are accessible through the RS-485 serial interface. Inverter function codes are mapped to RTU holding registers. An inverter function code RTU address is 2 bytes in length. The high byte corresponds to a code that represents the inverter parameter sort (F–M). The low byte corresponds to the inverter parameter number within the sort (0 -99).

Code	Sort	Name	Code	Sort
0	F	Basic function	5	A
1	E	Terminal function	6	o
2	C	Control function	7	S
3	P	Motor 1 function	8	M
4	H	High level function

Name Motor 2 function Option function Command/function data Monitor data

For example, inverter function code M11, output current, is addressed as RTU parameter number 080B hexadecimal or 2059 decimal.

9-4-6 Command and Monitor Data Registers

high byte	low byte
inverter parameter sort code	inverter parameter number

The command and monitor function codes are used to control the operation of the inverter and monitor the status variables through the serial interface. The command and monitor function codes are not accessible from the inverter keypad interface. Inverter parameter H30 and digital input signal LE must be enabled to operate the inverter from the Modbus interface. If LE is not assigned to a digital input (X1-X9), the signal will default to ON.

Frequency Setting Registers

Address	Code	Name	Unit	Variable Range	Min. unit	Read/	Data
						Write	Format
1793	S01	Frequency command	-	-20000–20000
				(max. frequency at ± 20000)	1	R/W	2
1797	S05	Frequency command	Hz	0.00–400.00	0.01	R/W	5

Note:

1)If both S01 and S05 are set, the inverter will ignore the setting of S05.

2)A data setting that exceeds the setting range is possible, but the actual action will be limited by the inverter configuration.

Operation command data Registers

Address	Code	Name	Unit	Variable Range	Min. unit	Read/	Data
						Write	Format
1798	S06	Operation command	-	Refer to the data format [14]	-	R/W	14
1799	S07	Universal Do	-	Refer to the data format [15]	-	R/W	15
1804	S12	Universal Ao	-	-20000–20000	1	R/W	2
				(100% output at ± 20000 )
Note:

1)Since X1–X9 are configurable input commands, it is necessary to set the functions by E01–E09.

2)The alarm reset is executed, when RST signal changes from ON to OFF even if there are no alarms.

3)Universal Do is a function that utilizes the inverter’s digital outputs via communication.

Function data Registers

Address	Code	Name	Unit	Variable Range	Min. unit	Read/	Data
						Write	Format
1800	S08	Acceleration time F07	s	0.1–3600.0	0.1	R/W	3
1801	S09	Deceleration time F08	s	0.1–3600.0	0.1	R/W	3
1802	S10	Torque limit level 1	%	20.00 –200.00, 999	1.00	R/W	5
		(driving) F40		(P11S:20.00-150.00)
1803	S11	Torque limit level 2	%	0.00, 20.00–200.00, 999	1.00	R/W	5
		(braking) F41		(P11S:20.00-150.00)

Note:

1)The writing of data out of range is treated as out of range error.

2)Use a value of 7FFFH to enter 999 for torque limit functions.

9-9