Fuji Bikes 5000G11S/P11S F09 Torque boost, F10 Electric thermal O/L relay Select F11 Level F12

F09 Torque boost 1

‹This is a function for motor 1. The following can be

<Constant torque>

Output voltage V

selected:

F 0 9 T R Q B O O S T 1

100%

Rated voltage 1

-- Selection of load characteristics such as automatic

#20.0

torque boost, square law reduction torque load,

proportional torque load, constant torque load.

-- Enhancement of torque (V/f characteristics), which is

10%

Base

#2.0 frequency 1

lowered during low-speed operation. Insufficient

magnetic flux of the motor due to a voltage drop in the

low-frequency range can be compensated.

	Setting range				Characteristics selected
	0.0				Automatic		torque		boost		characteristic
					where the torque boost value of a constant
					torque load (a linear change) is
					automatically adjusted.
					The motor tuning (P04 / A13) should be set
					to "2" for this function is valid.
	0.1 to 0.9				Square law		reduction torque for fan and
					pump loads.
	1.0 to 1.9				Proportional torque for middle class loads
					between square law reduction torque and
					constant torque (linear change)
	2.0 to 20.0				Constant torque (linear change)
‹
	Torque characteristics(30HP or less)
	<Square law reduction torque>							<Proportional torque>
Output voltage V							Output voltage V
100%			Rated voltage 1				100%			Rated voltage 1
			#0.9			Base			#1.9	Base
17%						frequency 1					frequency 1
				#0.1			17%				#1.0
0								0
			Output frequency f							Output frequency f
	<Constant torque>
Output voltage V
100%			Rated voltage 1
		#20.0
				Base
23%		#2.0		frequency 1
0
			Output frequency f
‹Torque characteristics(40HP or above)
	<Square law reduction torque>							<Proportional torque>
Output voltage V							Output voltage V
100%			Rated voltage 1				100%			Rated voltage 1
			#0.9		Base					#1.9	Base
18%					frequency 1		18%				frequency 1
				#0.1							#1.0
0								0
			Output frequency f							Output frequency f

0

Output frequency f

Note: As a large torque boost value creates overexcitation in the low-speed range, continued operation may cause the motor to overheating. Check the characteristics of the driven motor.

F10	Electric thermal O/L relay	( select)
F11	Electric thermal O/L relay	(level)
F12	Electric thermal O/L relay (Thermal time constant)

The electronic thermal O/L relay manages the output frequency, output current, and operation time of the inverter to prevent the motor from overheating when 150% of the set current value flows for the time set by F12 (thermal time constant).

‹This is a function for motor 1.

‹This function specifies whether to operate the electronic thermal O/L relay and selects the target motor. When a general-purpose motor is selected, the operation level is lowered in the low speed range according to the cooling characteristics of the motor.

F 1 0 E L C T R N O L 1

Set value 0: Inactive

1:Active (for general-purpose motor)

2:Active (for inverter motor)

‹This function sets the operation level (current value) of the electronic thermal. Enter a value from 1 to 1.1 times the current rating value of the motor.

‹The set value "2" is set for the inverter motor because there is no cooling effect decrease by the rotational speed.

F 1 1 O L L E V E L 1

The setting range is 20 to 135% of the rated current of the inverter.

	(%)	When F10 = 2
(%)	100
	95
current	90
	85
	69		4030toto60HP45kW
level	54	0.25 to 30HP	(WWhenhenF10F10= 1)= 1)
		(When F10 = 1)
Operation					(fb<60Hz)
			fe=	fb
				60Hz (fb≥60Hz)
					fb:Base frequency

Fe x 0.33 Fe x 0.83 fe

Output frequency f0 (Hz)

Operation level current and output frequency

5-10