Guardian Technologies N7001V2 6139AV Audio, VIM Module, Programming, Information For, 36 Ð

		2. Connect 3 wires from terminals 1, 2, and 3 on the right side of the VIM module
			to the control, as follows:
			a. Terminal 1 to the ground terminal (30) on the control.
			b. Terminals 2 and 3 to the ÒhandsetÓ terminals (26 & 27) on the control.
6139AV	Audio	Each 6139AV 2-way Keypad requires a shielded 2-wire connection to the VIM
Connections To		Module. Splice the flying leads of the supplied SA550AB Audio Bus connector
The VIM Module		to this shielded cable, then plug the connector into the 6139AV keypad's J5
		connector located on the right of the keypad, just beneath the PC board.
		Connect the 6139AV keypad(s) to the VIM module as follows:
			Keypad 1 (and Keypad 4, if used): to terminals 1, 2, and 3
			Keypad 2 (and Keypad 5, if used): to terminals 4, 5, and 6
			Keypad 3 (and Keypad 6, if used): to terminals 7, 8, and 9.
		IMPORTANT: Connect the shield at the VIM module, but not at the
		keypad, as shown in the VIM connection diagram.
		If more than three 6139AV keypads are used (up to six 6139AV keypads can be
		supported), connect as follows: keypad 4 in parallel with keypad 1, keypad 5 in
		parallel with keypad 2, and keypad 6 in parallel with keypad 3.
		Terminal 10 can, if you wish, be connected to the audio output on the 4285
		module (terminal 6 or 7), if the phone module is used in the system. This will allow
		the voice output heard through a telephone via the phone module to be heard
		through the built-in speaker in the 6139AV keypad(s).
Programming		When programming the system, use #93 Menu ModeÐDevice Programming to
Information	For the	program the following:
VIM	Module	¥	Device address as set by the DIP switches (01Ð15).
		¥	Device type "7".
		¥	Partition 1, partition 2, automatic or all.
		¥	Voice session timeout duration (5 min, 10 min, 15 min, or no timeout).

†COMPATIBLE WITH SELECTED KEYPADS AND CONTROLS

2-WAY †

2-WAY †

2-WAY †

CONNECT TO CONTROL’S KEYPAD TERMINALS

VOICE

VOICE

VOICE

{USING CONNECTOR SUPPLIED WITH KEYPAD

KEYPAD

J5

KEYPAD

J5

KEYPAD

J5

USE SA550AB AUDIO CONNECTOR SUPPLIED WITH KEYPAD

i

i

TO J5

l

l

l

l

AUDIO

l l

VIM

CONNECTIONS

(VOICE INTERFACE MODULE)

1

STATUS

KEYPADS

R

LEDs

1

#1 AND #4

G

2

HANDSET

2

3

{

USE 2-WIRE SHIELDED CABLE TO CON-

RING

SHIELD

NECT 2-WAY VOICE KEYPADS TO VIM

HANDSET

3

MODULE. CONNECT SHIELD AT VIM

TIP

4

{

MODULE, BUT NOT AT KEYPAD.

5

KEYPADS

SHIELD

#2 AND #5

6

	7				4-PIN
				MICRO-	HEADER
		KEYPADS
	8			PROCESSOR
		{#3 AND #6	ON
	SHIELD
			1
	9
AUDIO OUTPUT	10	DIP
PHONE		SWITCH	5
MODULE

VIM STATUS LED FUNCTIONS

RED ON	TALK SINGLE
RED FLASH	TALK TO ALL
GREEN ON	VOX MODE
BOTH ON	LISTEN SINGLE
BOTH FLASH	LISTEN ALL
ALT. FLASH	WAIT ID CODE
BOTH OFF	IDLE

TO EARTH GROUND

TO CONTROL’S { HANDSET

TERMINALS

CONNECTOR WITH 4 FLYING LEADS CON-

{ NECTS TO CONTROL’S KEYPAD TERMINALS

IMPORTANT: SET DIP

SWITCHES BEFORE CON- NECTING 4-PIN PLUG.

YELLOW

NOT USED

RED

BLACK

GREEN

(SUPPLIED WITH VIM)

IMPORTANT:

SET DIP SWITCHES BEFORE CONNECTING 4-PIN CONNECTOR FROM CONTROL’S KEYPAD TERMINALS.

5		ON	{
OFF
	1	ON
	2
	3
	4

(SHOWN SET FOR

ADDRESS “7”)

*ADDRESS 4 RESERVED FOR VISTA INTERACTIVE PHONE MODULE

SWITCH

DIP SWITCH SETTINGS

POSITION

1

2

3

*4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

1

–

ON

–

ON

–

ON

–

ON

–

ON

–

ON

–

ON

–

ON

–

ON

–

ON

–

ON

–

ON

–

ON

–

ON

–

ON

2

ON

–

–

ON

ON

–

–

ON

ON

–

–

ON

ON

–

–

ON

ON

–

–

ON

ON

–

–

ON

ON

–

–

ON

ON

–

3

ON

ON

ON

–

–

–

–

ON

ON

ON

ON

–

–

–

–

ON

ON

ON

ON

ON

–

–

–

ON

ON

ON

ON

–

–

–

4

ON

ON

ON

ON

ON

ON

ON

–

–

–

–

–

–

–

–

ON

ON

ON

ON

ON

ON

ON

ON

–

–

–

–

–

–

–

5

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

CONNECTING THE ADEMCO VOICE INTERFACE MODULE (VIM)

Ð 36 Ð