Guardian Technologies N7001V2 Quick Arm, Subscriber Acct, Prevent Zone, Bypass, Swinger, Chime On

Partition-Specific Field Descriptions (continued)

*29	Quick Arm				Enter 1 to enable arming of the burglary system in AWAY, STAY, INSTANT or
					MAXIMUM modes by using the # key instead of the security code. When armed,
					reports closing as User 0 if open/close reporting for User #2 (typically a master
					level user) was enabled for a given partition. If quick arm is used, the installer code
					and authority level 5 code cannot disarm the system. Enter 0 if Quick Arm is not
					desired. In either case, the security code must always be used to disarm the
					system.
* 3 2	Primary				Enter a 3 or 4 digit (depending on report format) primary subscriber account
	Subscriber		Acct	#	number 00-09; B-F (11-15). Each number requires a 2-digit entry so as to allow
					entry of hexadecimal digits (B-F). If a 3 digit account number is to be used, only
					enter data in the first 3 locations, leaving the last one unfilled, by entering a *.
* 3 8	Prevent Zone XX				Entering a zone number (01-64) prevents that zone from being bypassed by the
	Bypass				user. Enter 00 if this feature is not desired (all zones can be bypassed). This does
					not affect fire zones, which the system prevents from being bypassed.
* 3 9	Open/Close		Report		Enter 1 if open/close reporting for the installer is desired. Otherwise enter 0
	For	Installer	Code		(disable).
* 8 4	Swinger				This option limits the number of messages (Alarms or Troubles) sent for a specific
	Suppression				channel in an armed period (Swinger Suppression). Enter 01-15. If 00 is
					selected, all Alarm or Trouble codes are reported. Must be 00 (disabled) for UL.
* 8 5	Enable Dialer				Enter 1 for each panic/duress for which reporting is desired. Otherwise enter 0
	For Panics &				(disable).
	Duress
* 8 7	Entry Warning				Enter 0 for 3 short beeps, or 1 for slow beeps that continue for the entire entry
					delay period.
* 8 8	Burg. Alarm				Enter 0 for no delay on burglary alarm communication, or 1 for 16-second delay
	Comm. Delay				(no delay on 24-hour reports).
* 9 0	Secondary				Enter the 3 or 4 digit number (depending on report format) for the secondary
	Subscriber		Acct	#	subscriber account, 00-09; B-F (11-15). Each number requires a 2-digit entry so
					as to allow entry of hexadecimal digits (B-F). If a 3-digit number is to be used, only
					enter data in the first 6 locations, leaving the last two unfilled. Default=15 15 15
					15. Erase the field by entering *90*. NOTE: This field must be programmed if a
					secondary phone number is used (field *34). This account number can be the
					same as the primary account number.
2nd Page		Fields
1 * 4 3 Permanent					Enter 1 if it is desired that backlighting for the keypad display remain on at all times.
	Keypad				Enter 0 if the display should remain unlit unless a key is pressed. The backlighting
	Backlighting				then turns off again after a period of keypad inactivity. Note that when a key is
					pressed, display backlighting turns on for all keypads in that partition.
1 * 4 5	Exit Delay				Enter 1 if beeps from the keypads during exit delay is desired. Enter 0 for no
	Sounding				keypad sound during exit delay.
1 * 4 7	Chime On				Enter 1 for chime annunciation using the external alarm sounder. If not desired,
	Ext. Siren				enter 0.
1 * 5 2	Send Cancel				Enter 1 if no report restriction is desired. Enter 0 if cancel reports are to be sent
	If Alarm + OFF				within Bell Timeout period only.
1 * 7 6	Access Control				The system can be programmed to provide user activated access control. If
	Relay				enabled, the assigned relay will pulse for 2 seconds when the user enters his
					code and presses "0". Enter the relay number (00-08) for the relay that will be
					used for access control. Enter 00 if not used in this partition.
3rd Page		Fields
2 * 1 8	Enable GOTO				Enter 1 if this partition is to be accessed by a GOTO command. Otherwise enter
	For	This Partition			0 .
2 * 2 0 Enable					0=disable for displayed partition; 1=enable for displayed partition
	J7	Triggers
	By	Partition
Ð 54 Ð