![](/images/new-backgrounds/1041748/41748101x1.webp)
Dialer Options (continued)
*8 0 Zone Type Restores
For Types
*8 1 - * 8 2
*8 9 Restore
Report Timing
2ND PAGE FIELDS
1*33
1*34 Comm. Split Report Selection
1 * 4 0 - 1 * 4 1 Arm Stay ÊÊ& Time Set Report Ê Ê C o d e s
Enter 1 to enable restore reporting for individual zone types. Enter 0 if no restore report is desired for a zone type.
Enter the appropriate report codes as indicated on the programming form.
Enter 0 for instant restore report, as zone restores. Enter 1 for reporting after bell timeout if zone restored. Enter 2 for restore report when system is subsequently disarmed
Enter 1 to enable Rotary
This field allows certain reports to be directed to either the primary or secondary phone number. Enter 0, 1, or 2, in accordance with the following: 0 = split reporting disabled; 1 = alarm, alarm restore & cancel reports sent to primary Telco number, all others to secondary Telco number; 2 = open/close & test reports sent to secondary Telco number and all other reports to primary. See *51 for split/dual reporting comments.
Enter the appropriate code as shown on the programming form.
Wireless Options
1 * 2 8 | RF TX Low | Enter 0 if audible beep and display annunciation upon RF transmitter low battery | |
| Battery | Sound | condition is desired only in disarmed state. Enter 1 if audible beep and display is |
|
|
| desired in both armed and disarmed states. Must be 1 for UL. |
1 * 2 9 | RF TX Low | Enter 1 if a trouble message for RF transmitter low battery conditions is to be sent | |
| Battery Report | to the central station. Enter 0 if no report for transmitter low battery is desired. | |
| Enable |
| Note that a trouble message will be sent for a transmitter supervision failure |
|
|
| independent of this selection. Must be 1 for UL. |
1 * 3 0 | RF Rcvr |
| Enter the |
| Supervision | hours | |
|
| Interval | entered will result in activation of the response type programmed for zone 90 for |
|
|
| the first receiver and zone 88 for the second receiver and their related |
|
|
| communication reports. Enter 00 to disable receiver supervision. Max. "6" (12 hr) |
|
|
| for UL. |
1 * 3 1 | RF Transmitter | Enter the | |
| Interval | hours | |
|
|
| within the time entered will result in a trouble response and related |
|
|
| communication report. Entry 00 disables transmitter supervision. Max. "6" (12 hr) |
|
|
| for UL. |
1 * 3 2 | Receiver | Type | Enter 1 if using 4281 series receivers. enter 2 if using 5881 series receivers. |
|
|
| 0 = none. |
1 * 4 4 | Wireless | Keypad | Enter 1 to enable tamper detection on wireless keypad. Enter 0 if tamper |
| Tamper Detect | detection is not desired. If this feature is enabled, any attempt to tamper by | |
|
|
| means of many trial entries at a wireless keypad will be blocked by the control |
|
|
| panel. If more than 40 key depressions are received without a valid sequence |
|
|
| (arm, disarm, etc.), the Control panel will disable the wireless keypad. The inhibit is |
|
|
| removed once a valid key sequence is received from a wired keypad. |
1 * 4 8 | Wireless | Keypad | Enter the partition in which the RF keypad is used, |
| Assignment | is used. | |
1 * 4 9 | Suppress | TX | Enter 1 to disable trouble sounding for transmitter |
| Supervision | audible trouble sounding is desired. Must be "0" for UL. | |
| Sound |
|
|
|
|
| Ð 51 Ð |