Guardian Technologies N7001V2, VISTA-40 installation instructions Dialer Options

Dialer Options (continued)

*4 3 Dial Tone Detection

*4 4 Ring Detection Count

* 4 5 Primary Format

*4 6 Low Speed Format (Primary)

* 4 7 Secondary Format

*4 8 Low Speed Format (Sec.)

*4 9 Checksum Verification

*5 0 Sescoa/Radionics Select

* 5 1 Dual Reporting

*5 2 Standard/ Expanded Report, Primary

*5 3 Standard/ Expanded Report, Secondary

*54-*78 Report Codes For Zones 1-64, 87-99

*7 9 Zone Type Restores For Zone Types 1-8

Ð 50 Ð

Determines whether the control will wait for a true dial tone before dialing, or if it will wait for a predetermined delay before dialing (delay is programmed in Dial Tone Pause field *42). The latter may be necessary in high-noise environment Telco networks where noise can be confused with dial tone, resulting in premature dialing. Enter 1 for true dial tone wait. If no dial tone is detected, will dial at end of pause programmed in field *42. Enter 0 to pause for seconds entered in field *42, then dial.

Only applicable if central station initiated downloading will be used. Enter 00 to disable ring detection. Enter 01-14for ring counts of 1-14. Enter 15 to select answering machine mode that allows the system to receive calls even when a telephone answering machines is connected to the same phone line. In the answering machine mode, the download caller should let the phone ring once, then hang up, then call again within 30 seconds. The system, upon hearing one ring followed by nothing, will not answer that call, but will ready itself to pick up on the first ring the next incoming call that is received within 30 seconds (the downloader calling again). DO NOT USE Ò00Ó if 4285 Phone module is being used. DO NOT USE Ò01Ó if the VIM module is being used.

This field selects the reporting format for use on the primary telephone line. Enter the appropriate number for the primary format as follows: 0=Low Speed; 1=Contact ID; 2=Ademco High Speed; 3=Ademco Express.

Note: Contact ID (1) is the only reporting format that will send a "listen-in to follow" message when using a n AAV unit.

Enter the appropriate value: 0=Ademco Low Speed; 1=Sescoa/Radionics

This field selects the reporting format for the secondary telephone line. Enter the appropriate number for the secondary format as follows: 0=Low Speed; 1=Contact ID; 2=Ademco High Speed; 3=Ademco Express

Enter the appropriate value: 0=Ademco Low Speed; 1=Sescoa/Radionics

Enter 1 for either or both primary/secondary formats to send a verification digit to validate the message at the receiver without having to send two message rounds. Valid for 3+1, 4+2, and Ademco High Speed reports. Enter 0 if not desired.

Enter 0 if Radionics format is to be used with hexadecimal 0-9, B-F reporting. Enter 1 if SESCOA format is to be used with only numeric reporting (0-9). This selection applies to both primary and secondary phone numbers.

This field allows all reports to be sent to both primary and secondary phone numbers. Enter 1 if it is desired that all reports are sent to both primary and secondary phone numbers. If dual reporting is desired and Ademco High Speed format is to be used at all, it must be selected as both the primary and secondary transmission formats. If used with Split Reporting option 1 (1*34), alarms go to both primary & secondary numbers, while all other reports go to secondary only. If used with Split Reporting option 2, open/close and test messages go to both lines, while all other reports go to primary.

Enter 0 for standard or 1 for expanded reporting for the primary phone line. Note: Expanded overrides 4+2 format.

Enter 0 for standard or 1 for expanded reporting for the secondary phone line. Note: Expanded overrides 4+2 format.

Enter the appropriate report codes for each zone used in the system.

Enter 1 to enable restore reporting for individual zone types. Enter 0 if no restore report is desired for a zone type.