Guardian Technologies VISTA-40 Protection zone, 6139AV Keypad Audio, Level Adjustment, 37 Ð

		¥	Chime option for other partition during 2-way voice session.
		¥	VIM text option for displaying voice mode text at the keypad.
		¥	VIM AC loss option, when enabled, allows 2-way voice communication after AC
			loss (recommended for installations where someone is on a life support device)
		¥	The AUTO CALLBACK option, when enabled, allows callback to initiate 2-way
			voice communication, otherwise Òlisten in to followÓ (event code 606) is sent at
			end of alarm report.
Programming		¥	Device address as programmed at the keypad (01-15). Address 00 not
Information	For the		applicable. NOTE: Address 04 is reserved for the 4285 phone module.
6139AV	Keypad	¥	Device type "8".
		¥	Voice keypad number (01Ð16); this is the keypad's identification number from
			the central station operator's point of view. 01Ð06 is recommended.
		¥	Keypad's partition (1Ð2).
		¥	Keypad's sounder option (0Ð2)

Program VIM fault and siren silencing options by using the #93 Menu Mode - Relay Programming menu (see Section 4 in the PART 2. PROGRAMMING GUIDE section of this manual).

AAV	Notes	1.	The 685 Receiver software must be rev. 4.6 or higher. Earlier versions will not
			hold the phone line connection, or if AUTO CALLBACK is enabled, any
			receiver can be used.
		2.	Contact ID code for "listen-in to follow" is "606" if AUTO CALLBACK is
			disabled.
		3.	Field 1*60 must be set for "0" when using the Ademco VIM module. If using
			another manufacturerÕs AAV module, enter Ò1Ó.
			NOTE: If set to Ò1Ó, zone 5 is no longer available as a
			protection zone.
		4.	Contact ID (field *45 =1) is the only reporting format that will send a "listen-in
			to follow" message if AUTO CALLBACK is disabled.
		5.	Listen-in to follow message is sent only if both the VIM and at least one
			6139AV 2-way voice keypad is programmed using #93 Device Programming
			mode if AUTO CALLBACK is disabled.
		6.	Operator callback and AUTO CALLBACK option is enabled if a non- leading-
			zero 4-digit number is programmed in field 1*59.
		7.	Make sure that field *44 (RING DETECTION COUNT) is not set to Ò01Ó.
6139AV Keypad	Audio	The 6139AVÕs audio level for "talk mode" and "VOX mode" can be programmed
Level Adjustment		for "high," "medium," or "low." The factory default is "high."
		1.	Enter the keypad's programming mode by pressing and holding down the [1]
			and [3] keys at the same time for 3 seconds. The keypad's address is
			displayed.
		2.	a. Press and hold down the "D" key for 2 seconds. The current talk mode
			audio level is displayed (high, medium, or low).
			b. Press the [#] key repeatedly to toggle the talk mode level settings from
			high to medium to low until the desired level is displayed.
		3.	a. Press the "D" key again to enter VOX mode level setting. The current
			VOX mode audio level is displayed (high, medium, or low).
			b. Press the [#] key repeatedly to toggle the VOX mode level settings from
			high to medium to low until the desired level is displayed.
		4.	Pressing the "D" key again returns to the talk mode level setting, etc.
			Press [*] to exit keypad programming mode.

Notes:

¥The keypad returns to normal mode if no key is pressed for 30 seconds.

¥Powering down the keypad does not change the level setting.

¥To eliminate undesired keypad feedback (microphonics) during a 2-way audio session, reduce the VOX mode audio level one level at a time until the feedback stops.

Ð37 Ð