Guardian Technologies N7001V2, VISTA-40 installation instructions IMPORTANT! Fault Annunciation

	Type 05	This zone type will give an instant alarm if faulted when armed in the Away, Stay,
Trouble	by Day/Alarm	Instant or Maximum (night) modes. During the disarmed state (day), the system
	by Night.	will provide a latched trouble sounding from the keypad (and a central station
		report, if desired). This zone type is usually assigned to a zone which contains a
		foil-protected door or window (such as in a store), or to a zone covering a
		"sensitive" area such as a stock room, drug supply room, etc. This zone type can
		also be used on a sensor or contact in an area where immediate notification of an
		entry is desired.
	Type 06	This zone type sends a report to the Central Station but provides no keypad
24-hour	Silent Alarm.	display or sounding. This zone type is usually assigned to a zone containing an
		Emergency button.
	Type 07	This zone type sends a report to the Central Station, and provides an alarm sound
24-hour Audible Alarm.		at the keypad, and an audible external alarm. This zone type is usually assigned to
		a zone that has an Emergency button.
	Type 08	This zone type sends a report to Central Station and provides an alarm sound at
24-hour Auxiliary		the keypad. (No bell output is provided). This zone type is usually
	Alarm.	assigned to a zone containing a button for use in personal emergencies, or to a
		zone containing monitoring devices such as water sensors, temperature sensors,
		etc.
	Type 09	This zone type provides a fire alarm on short circuit and a trouble condition on
Supervised Fire. (No		open circuit. The bell output will pulse when this zone type is faulted. This zone
	Verification)	type is always active and cannot be bypassed. This zone type can be
		assigned to any hard-wired zone except zone 9, any polling loop
		zone, and certain wireless zones.
	Type 1 0	This zone type gives entry delay (using the programmed entry delay 1 time), if
Interior w/Delay.		tripped when the panel is armed in the Away mode. This zone type is also active
		during maximum mode, but no delay is provided (alarms occur immediately if zone
		is tripped). This zone type is bypassed when the panel is armed in
		the Stay or Instant modes. Delay begins whenever sensors in this zone are
		violated, regardless of whether or not an entry/exit delay zone was tripped first.
	Type 20	This is a special-purpose zone type used with 5800 series wireless pushbutton
	Arm-Stay*	units which will result in arming the system in the STAY mode when the zone is
		activated.
	Type 21	This is a special-purpose zone type used with 5800 series wireless pushbutton
	Arm-Away*	units which will result in arming the system in the AWAY mode when the zone is
		activated.
	Type 22	This is a special purpose zone type used with 5800 series wireless pushbutton or
	Disarm*	contact closure or opening, and which will result in disarming the system when
		the zone is activated.
	Type 23	This zone type can be used on a zone when an output relay action is desired, but
No Alarm Response		with no accompanying alarm (ex. lobby door access).
		* These zone types are not for use by 5700 series devices.
		NOTE FOR PANIC KEYS
		Keypad panic zones share the same zone response type for both partitions, but
		panics may be individually enabled for each partition.
		IMPORTANT! FAULT ANNUNCIATION
		Phone module, RF, VIM and polling loop faults (zones 87, 88-91, 93 & 97) will
		report as trouble conditions only, and as such, should be assigned either zone
		type 00 if no annunciation is desired, or zone type 05 if annunciation as trouble
		condition is desired. See FAULT ANNUNCIATION notes in POLLING LOOP and
		WIRELESS EXPANSION sections for more information.

Ð 44 Ð