DATA FIELD DESCRIPTIONS
The following section arranges the global (system wide) program fields into the following functional groups:
Control Options Downloading Options Dialer Options Wireless Options Partitioning Options Event Logging Options
|
|
|
| Note that zone response types can be programmed in fields |
|
|
|
| |
|
|
|
| Mode. For this reason, these fields are not discussed in this section. |
Control Options |
|
| ||
* 0 0 | Installer Code | The Installer's Code is a | ||
|
|
|
| can be used by the customer if needed. This is the only code that can be used to |
|
|
|
| enter the Program mode from the keypad. This code cannot be used to disarm |
|
|
|
| the system if not used to arm, or if Quick Arm was used to arm system. This code |
|
|
|
| cannot reenter programming mode if exited by the *98 command. |
* 1 4 | Zone 9 |
|
| Enter 1 to set fast response mode (10 mSec) for appropriate devices wired to |
| Response Time | zone 9. Enter 0 for normal response, 350 msec. Must be 0 for UL. | ||
* 1 5 | Keyswitch | Enter the partition number | ||
| Assignment | enter 0. Requires the use of zone 7 wired loop (zone 7 no longer available as | ||
|
|
|
| protection zone when used for keyswitch operation). If the keyswitch is used, the |
|
|
|
| fire and panic alarm voltage triggers automatically become ARMING and READY |
|
|
|
| status outputs for support of the Keyswitch LEDs. NOTE: Zone type 10 is |
|
|
|
| automatically assigned to zone 7 if a keyswitch is used. Reports openings/closing |
|
|
|
| by user "0" if reporting is enabled in field *40. |
* 1 7 | AC Loss Keypad | Entering 1 enables sounding at the keypad (rapid beeping) when AC power is | ||
| Sounding | lost is desired. Enter 0 if no AC power loss keypad sounding is desired. | ||
* 1 8 | UL AC Loss | Entering 1 enables the external alarm sound after AC power has been out for 4 | ||
| Siren |
|
| hours; otherwise enter 0 (no alarm). |
* 1 9 | Randomize | Enter 1 to randomize AC loss reporting between | ||
| AC Loss Report | loss. Enter 0 for normal AC loss reporting (about 2 minutes after actual AC loss). | ||
|
|
|
| Selecting this option helps prevent an overload of AC loss messages at the central |
|
|
|
| station during a community blackout. |
* 2 0 | Phone | Module | If an 4285 phone module is being used, enter the | |
| Phone | Code | access the system. Enter | |
|
|
|
| second digit. To disable the phone module, enter 00 for the 1st digit and enter |
|
|
|
| 11 for the 2nd digit of the code (disable code = [0T]). Must be disabled for UL |
|
|
|
| installations. |
* 2 1 | Prevent | Fire | Enter 1 to disable (no timeout) the alarm sounder duration for any zone | |
|
| designated as a fire zone, regardless of partition, so that fire sounding continues | ||
|
|
|
| until the system is reset. Enter 0 if the normal burglary alarm sounder duration |
|
|
|
| (programmed in |
* 2 4 | Ignore | Expansion | Only applicable if certain polling loop RPMs or 5800 series transmitters are used. | |
| Zone Tamper | This option is used to disable this module's tamper detection. Enter 1 to disable. | ||
|
|
|
| Enter 0 if tamper detection is desired. |
* 2 5 | Burg. Trigger For | This field allows optional triggering of the voltage output on pin 7 of the J7 header | ||
| Response Type 8 | for zone response type 8 (24hr. auxiliary). The 0 disable selection is useful if J7 | ||
|
|
|
| header pin 7 is used for a panic trigger, and |
|
|
|
| zones assigned to zone response type 8 (e.g. water sensor, temp. sensor). If |
|
|
|
| disabled, only burglary or audible panic alarms will trigger pin 7. Otherwise, enter 1. |
* 2 6 | Intelligent | Enter 1 if it is desired that no test report be sent if any other type of report was sent | ||
| Test Reporting | since the last test report. Enter 0 if test reports are to be sent at the set intervals, | ||
|
|
|
| regardless of other reports having been sent. Must be 0 for UL applications. |
Ð 47 Ð
