Remote Monitor | Liebert Series 600T manual

Remote Monitor

The Remote Monitor Panel (optional) displays eight (8) alarms. These alarms are also available for customer use through a set of contacts on a separate terminal board.

When the New Alarm, System Summary Alarm, or Module Summary Alarm is activated, you can get more information at the Operator Display Panel or through a remote terminal. Refer to 3.1.14 - Communication Interfaces.

.

SCC and Module Remote Monitor Indications

SCC Remote Monitor Indications	Channel	Module Remote Monitor Indications
Load On UPS	CH1	Output CB Open
Load On Bypass	CH2	Battery CB Open
Battery Discharging	CH3	Battery Discharging
Low Battery Warning	CH4	Low Battery Warning
Overload	CH5	Control Failure
Ambient Over-Temp	CH6	Ambient Over-Temp
System Summary Alarm	CH7	Module Summary Alarm
New Alarm	CH8	New Alarm

The following alarms, as well as those listed above, will activate the System Summary Alarm or the Module Summary Alarm.

Other Alarms That Activate Summary Alarms

Other Alarms That Activate	Other Alarms That Activate
System Summary Alarm	Module Summary Alarm
Control Power Fail	Blower Failed
Emergency Off	Control Power Fail
Module Summary Alarm	DC Capacitor Fuse Blown
Output Over/Under Frequency	DC Ground Fault
Output Over-Voltage	DC Over-Voltage Shutdown
Output Under-Voltage	Emergency Off
Overload Transfer	Equipment Over-Temperature
Static Switch Unable	Inverter Fault
	Low Battery Shutdown
	Overload
	Overload Shutdown
	Rectifier Fuse Blown
	Reverse Power

54	Operation	DISCONTINUED
		PRODUCT

Image 60

Liebert Series 600T manual Remote Monitor

Contents

Series 600T UPS DIS Product Table of Contents Manual Procedures Figures Tables Important Safety Instructions Overview of this Manual System Description Multi-Module UPS, 65-80 kVA left and 100-500 kVA right Product Multi-Module 500-750 kVA UPS Types of System Control Cabinets SCCs System Control Cabinets SCCs Reliability Designed for SuccessOther Factors to Consider Safety Precautions Modes of Operation Operator Controls DIS Product Options General Component Descriptions System Control Cabinet Battery Plant UPS Module Detailed Component Descriptions Controls HardwareFirmware Rectifier/Charger Input Power Factor Battery Charging CircuitInput Circuit Breaker Isolation Transformer Battery Disconnect Battery Charge Current LimitingBattery Equalize Charge Circuit Operation After End-of-Discharge Non-Linear Load Characteristics Unbalanced Load CharacteristicsInverter Output Regulation and Overload Performance Static Switch Isolation Static BypassFuse Protection Shorted SCR Monitoring Pulsed Parallel Operation Load Transfers Transfer and Retransfer Conditions Automatic Transfers to BypassManual Transfers Transfer Inhibited Redundant Mode Manual RetransfersRetransfer Inhibited Features Display Screen and Operator Controls Description Function System Control Cabinet Operator Controls Sccb Pictured Shutdown Procedures Description Location Function Switches Behind SCC Control Panel Door Menu Tree Master Menu Screen WALK-IN Display modules only Load Transfer Procedures SCC only Battery Time modules onlyCustomer Alarm Definitions SCC only Monitor/Mimic Display Screen Input Metering DisplaysOutput Metering Displays Status/Alarm Message Areas Item 7 Alarm MessagesItem 5 Module Status Messages Item 6 System Status Messages Module Monitor/Mimic Display Screen Alarm Messages Item 5 Alarm Messages MOD 1 on Line MOD 2 on Line MOD 3 on Line UPS Ratings UPS Input PWR UPS Ratings UPS Input PWR Bypass Input Load Bypass Input C-A Walk-In Display Screen Walk-In Display Screen During Start-Up Status Reports Screens Status Reports Screen Present Status Select Exit Event History Event History MODULE-0 History Status History Status Report Screens SCC Module Battery Cycle Monitor Module Only System Status Battery Cycle Monitoring Summary Screen System Configuration Screens System Configuration Date Date Screen Time Time Screen Auto Dial Dial Modem Baud Rate Modem Baud Rate Maximum Auto-Retransfer Attempts Retransfer Attempts Remote Monitor Alarm Limit Settings Screen Alarm Settings Product Load Transfer Procedures Screen Refer to 3.3.2 Load Transfer Procedures for more details Start-Up Procedures Screen Refer to 3.3.1 Start-Up Procedure for more details Module Start- Up Procedures Screen Shutdown Procedures Screen Shutdown Procedures Module Shutdown Procedures Screen Battery Time Screen Module Only VDC Battery Time Screen Example 45 Minute Discharge Range of Values for Calculated Battery Times Aining Rem Tim Calculated La p s e d T im e M in u te s Meter Calibration Screen UP Cursor UP Down Cursor Down Select Choose Battery Equalize Screen Battery Equalize Recharging Alarm and Status Messages Module Status Messages 3 Modules Connected System Status Messages Load Block Messages Abbreviations Used in Alarm Messages OF/UF DC Ground Fault Battery CB OpenPower Battery Manual Reset Static SwitchBypass Phase Control Power Alarm Indications and Other Alarms That Activate Summary AlarmsSystem Configuration Screens or the watchdog timer has Reverse Power Temperature Over-TemperatureTimeout System Configuration Screens Load On UPS Alarm Message Special Functions Communication Interfaces Worldwide ReportingAuto-Dial Requesting Information Local Reporting to a Terminal Local Reporting to a MonitorSite Reporting SiteScan or Snmp Remote Monitor Panel Separate / Simultaneous Outputs Load On Bypass Scct OK To Transfer Load on Bypass UPS Available Load on UPS Bypass Available Momentary Overloads Refer to 3.4 Automatic Operations Input Power Failure Load On Battery Input Power Fail Load on Battery One Module Off-Line One Module Off-Line Load on UPS Off Battery Load on UPS Battery Not Available Refer to 3.3.3 Shutdown Procedures Emergency Modules Off Emergency Power Off Emergency Power Off Refer to 3.2.10 Maintenance Bypass System Shutdown Load on Maintenance Bypass Two Breakers Load on Maintenance Bypass Three Breakers Manual Procedures Refer to 3.4 Automatic Operations for more details Start-Up Procedure SCC Start-Up B2. Set the Static Switch Disconnects OFF open SCC Start-Up Procedures Screen UPS Module Start-Up Module Start-Up Procedures Screen Product Load Transfer Procedures Maintenance Bypass Load Transfers Maintenance BypassIf the load is on Maintenance Bypass System Bypass Shutdown Procedures System Shutdown Procedure UPS bypass line is still energized 100 Module Shutdown Procedure Remote Emergency Power Off Repo Local Emergency Modules Off Lemo Automatic Operations Overloads Without Transfer Automatic Transfers to Bypass Automatic Retransfers to UPS Automatic Module Off-Line Automatic Emergency Modules Off Maintenance DIS Product Liebert Global Services Maintenance Agreements The Signature ProgramProfessional Start-Up Training Routine Maintenance Record LogAir Filters Battery Maintenance Battery Safety Precautions DIS Product 112 DIS Product Matching Battery Cabinets Optional Power BatteriesRack-Mounted Batteries Torque Requirements Torque Specifications Unless Otherwise Labeled Detection of Trouble Reporting a Problem Corrective ActionsRecommended Test Equipment Rating Environmental Conditions Adjustments Battery Operation Electrical Specifications Voltage Adjustment Range Phase BalancingVoltage Transient Recovery Time Voltage Harmonic Content Series 600T UPS