Modules Connected | Liebert Series 600T specs

3.1.13Alarm and Status Messages

Module Status Messages

The module status messages indicate how many UPS modules are included in the system and the present status of each module.

The following status messages may appear in the module status area.

1.MOD N. A module status message line is displayed for each UPS module in the system. Up to six (6) modules may be included in a multi-module system. The N in the message will indicate a specific UPS module number, 1 through 6.

2.ON LINE. The UPS module output circuit breaker is closed and power from the module is available to the SCC. The module output is sharing the critical load if the UPS Output Breaker is closed.

3.OFF-LINE.The UPS module output circuit breaker is open. More specific alarm messages are displayed at the UPS module.

4.SUM ALM. The Module Summary Alarm has been activated by one of the alarm messages listed in two tables—SCC and Module Remote Monitor Indications and Other Alarms That Activate Summary Alarms—in 3.1.5 - System Configuration Screens. The specific alarm message is displayed at the UPS module.

5.COM FAIL. The UPS module is not communicating with the SCC. This could mean loss of power to the UPS module controls, a disconnected cable, or a control logic failure (detected by watchdog timer. Call Liebert Global Services if you require assistance. To resume communication after control power is restored, sequence display to Master Menu.

Figure 46 SCC Status and Alarm Message Areas

BYPASS INPUT

A-B	B-C C-A
0V	0V	0V
	0 Hz

UPS INPUT PWR A-B B-C C-A

0V 0V 0V

MOD 1 ON LINE SUM ALM MOD 2 ON LINE SUM ALM MOD 3 ON LINE SUM ALM

UPS RATINGS

SCCT 1600

OUTPUT VOLTAGE

A-B B-C C-A

480V 480V 480V

60.0 Hz

Not OK to Transfer

Static Switch Connected

LOAD

627 KVA / 502 KW A B C 755A 755A 755A

3 OF 3 MODULES

CONNECTED

REDUNDANT Time To Overload Transfer: XXXX SEC

Byp Not Avail

Static Sw Unable

Module Sum Alm

MODULE STATUS	SYSTEM STATUS	LOAD BLOCK	ALARM
MESSAGES	MESSAGES	MESSAGES	MESSAGES

Operation 67

DISCONTINUED

PRODUCT

Image 73

Liebert Series 600T manual Alarm and Status Messages Module Status Messages, Modules Connected

Contents

Series 600T UPS DIS Product Table of Contents Manual Procedures Figures Tables Important Safety Instructions Overview of this Manual Multi-Module UPS, 65-80 kVA left and 100-500 kVA right System Description Product Multi-Module 500-750 kVA UPS System Control Cabinets SCCs Types of System Control Cabinets SCCs Designed for Success ReliabilityOther Factors to Consider Safety Precautions Modes of Operation Operator Controls DIS Product Options System Control Cabinet General Component Descriptions UPS Module Battery Plant Controls Hardware Detailed Component DescriptionsFirmware Rectifier/Charger Battery Charging Circuit Input Power FactorInput Circuit Breaker Isolation Transformer Battery Charge Current Limiting Battery DisconnectBattery Equalize Charge Circuit Operation After End-of-Discharge Unbalanced Load Characteristics Non-Linear Load CharacteristicsInverter Output Regulation and Overload Performance Static Bypass Static Switch IsolationFuse Protection Shorted SCR Monitoring Load Transfers Pulsed Parallel Operation Automatic Transfers to Bypass Transfer and Retransfer ConditionsManual Transfers Transfer Inhibited Manual Retransfers Redundant ModeRetransfer Inhibited Display Screen and Operator Controls Features Description Function System Control Cabinet Operator Controls Sccb Pictured Description Location Function Shutdown Procedures Switches Behind SCC Control Panel Door Menu Tree WALK-IN Display modules only Master Menu Screen Battery Time modules only Load Transfer Procedures SCC onlyCustomer Alarm Definitions SCC only Input Metering Displays Monitor/Mimic Display ScreenOutput Metering Displays Item 7 Alarm Messages Status/Alarm Message AreasItem 5 Module Status Messages Item 6 System Status Messages Module Monitor/Mimic Display Screen Item 5 Alarm Messages Alarm Messages MOD 1 on Line MOD 2 on Line MOD 3 on Line UPS Ratings UPS Input PWR UPS Ratings UPS Input PWR Bypass Input Load Bypass Input C-A Walk-In Display Screen During Start-Up Walk-In Display Screen Status Reports Screen Status Reports Screens Select Exit Present Status Event History MODULE-0 Event History History Status Report Screens History Status Module SCC System Status Battery Cycle Monitor Module Only Battery Cycle Monitoring Summary Screen System Configuration System Configuration Screens Date Screen Date Time Screen Time Dial Auto Dial Modem Baud Rate Modem Baud Rate Retransfer Attempts Maximum Auto-Retransfer Attempts Remote Monitor Alarm Settings Alarm Limit Settings Screen Product Refer to 3.3.2 Load Transfer Procedures for more details Load Transfer Procedures Screen Refer to 3.3.1 Start-Up Procedure for more details Start-Up Procedures Screen Module Start- Up Procedures Screen Shutdown Procedures Shutdown Procedures Screen Module Shutdown Procedures Screen VDC Battery Time Screen Module Only Battery Time Screen Example 45 Minute Discharge Aining Rem Tim Calculated La p s e d T im e M in u te s Range of Values for Calculated Battery Times UP Cursor UP Down Cursor Down Select Choose Meter Calibration Screen Battery Equalize Recharging Battery Equalize Screen 3 Modules Connected Alarm and Status Messages Module Status Messages Load Block Messages System Status Messages OF/UF Abbreviations Used in Alarm Messages Battery CB Open DC Ground FaultPower Battery Static Switch Manual ResetBypass Phase Control Power Indications and Other Alarms That Activate Summary Alarms AlarmSystem Configuration Screens or the watchdog timer has Reverse Power Over-Temperature TemperatureTimeout System Configuration Screens Load On UPS Special Functions Alarm Message Worldwide Reporting Communication InterfacesAuto-Dial Requesting Information Local Reporting to a Monitor Local Reporting to a TerminalSite Reporting SiteScan or Snmp Remote Monitor Panel Separate / Simultaneous Outputs Scct Load On Bypass Load on Bypass UPS Available OK To Transfer Load on UPS Bypass Available Refer to 3.4 Automatic Operations Momentary Overloads Input Power Fail Load on Battery Input Power Failure Load On Battery One Module Off-Line Load on UPS One Module Off-Line Load on UPS Battery Not Available Off Battery Emergency Modules Off Refer to 3.3.3 Shutdown Procedures Emergency Power Off Emergency Power Off System Shutdown Refer to 3.2.10 Maintenance Bypass Load on Maintenance Bypass Two Breakers Load on Maintenance Bypass Three Breakers Refer to 3.4 Automatic Operations for more details Manual Procedures Start-Up Procedure SCC Start-Up B2. Set the Static Switch Disconnects OFF open SCC Start-Up Procedures Screen UPS Module Start-Up Module Start-Up Procedures Screen Product Load Transfer Procedures Maintenance Bypass Maintenance Bypass Load TransfersIf the load is on Maintenance Bypass System Bypass UPS bypass line is still energized Shutdown Procedures System Shutdown Procedure 100 Module Shutdown Procedure Local Emergency Modules Off Lemo Remote Emergency Power Off Repo Overloads Without Transfer Automatic Operations Automatic Retransfers to UPS Automatic Transfers to Bypass Automatic Emergency Modules Off Automatic Module Off-Line Maintenance DIS Product Maintenance Agreements The Signature Program Liebert Global ServicesProfessional Start-Up Training Record Log Routine MaintenanceAir Filters Battery Safety Precautions Battery Maintenance DIS Product 112 DIS Product Power Batteries Matching Battery Cabinets OptionalRack-Mounted Batteries Torque Requirements Detection of Trouble Torque Specifications Unless Otherwise Labeled Corrective Actions Reporting a ProblemRecommended Test Equipment Rating Environmental Conditions Battery Operation Adjustments Electrical Specifications Phase Balancing Voltage Adjustment RangeVoltage Transient Recovery Time Voltage Harmonic Content Series 600T UPS