Series 600T UPS | Liebert specs

Series 600T™ UPS

Multi-Module Three Phase 65 kVA to 750 kVA; 60 Hz

Technical Support

U.S.A.	1-800-222-5877
Outside the U.S.A.	614-841-6755
U.K.	+44	(0) 1793 553355
France	+33	1 4 87 51 52
Germany	+49	89 99 19 220
Italy	+39	2 98250 1
Netherlands	+00	31 475 503333
E-mail	upstech@liebert.com
Web site	http://www.liebert.com
Worldwide FAX	614-841-5471
tech support

The Company Behind The Products

With more than 500,000 installations around the globe, Liebert is the world leader in computer protection sys- tems. Since its founding in 1965, Liebert has developed a complete range of support and protection systems for sensitive electronics:

•Environmental systems: close-control air conditioning from 1.5 to 60 tons.

•Power conditioning and UPS with power ranges from 250 VA to more than 1000 kVA.

•Integrated systems that provide both environmental and power protection in a single, flexible package.

•Monitoring and control — on-site or remote — from systems of any size or location

Service and support, through more than 100 service centers around the world, and a 24-hour Customer Response Center.

While every precaution has been taken to ensure accuracy and completeness of this literature, Liebert Corpora- tion assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions.

© 1999 Liebert Corporation. All rights reserved throughout the world. Specifications subject to change without notice.

®Liebert and the Liebert logo are registered trademarks of Liebert Corporation. All names referred to are trade- marks or registered trademarks of their respective owners.

Printed in U.S.A.

SL-30024

Revised: February 1999

DISCONTINUED PRODUCT

Image 128

Liebert manual Series 600T UPS

Contents

Series 600T UPS DIS Product Table of Contents Manual Procedures Figures Tables Important Safety Instructions Overview of this Manual System Description Multi-Module UPS, 65-80 kVA left and 100-500 kVA right Product Multi-Module 500-750 kVA UPS Types of System Control Cabinets SCCs System Control Cabinets SCCs Other Factors to Consider ReliabilityDesigned for Success Safety Precautions Modes of Operation Operator Controls DIS Product Options General Component Descriptions System Control Cabinet Battery Plant UPS Module Detailed Component Descriptions Controls HardwareFirmware Rectifier/Charger Input Power Factor Battery Charging CircuitInput Circuit Breaker Isolation Transformer Battery Disconnect Battery Charge Current LimitingBattery Equalize Charge Circuit Operation After End-of-Discharge Non-Linear Load Characteristics Unbalanced Load CharacteristicsInverter Output Regulation and Overload Performance Static Switch Isolation Static BypassFuse Protection Shorted SCR Monitoring Pulsed Parallel Operation Load Transfers Transfer and Retransfer Conditions Automatic Transfers to BypassManual Transfers Transfer Inhibited Retransfer Inhibited Redundant ModeManual Retransfers Features Display Screen and Operator Controls Description Function System Control Cabinet Operator Controls Sccb Pictured Shutdown Procedures Description Location Function Switches Behind SCC Control Panel Door Menu Tree Master Menu Screen WALK-IN Display modules only Customer Alarm Definitions SCC only Load Transfer Procedures SCC onlyBattery Time modules only Output Metering Displays Monitor/Mimic Display ScreenInput Metering Displays Status/Alarm Message Areas Item 7 Alarm MessagesItem 5 Module Status Messages Item 6 System Status Messages Module Monitor/Mimic Display Screen Alarm Messages Item 5 Alarm Messages MOD 1 on Line MOD 2 on Line MOD 3 on Line UPS Ratings UPS Input PWR UPS Ratings UPS Input PWR Bypass Input Load Bypass Input C-A Walk-In Display Screen Walk-In Display Screen During Start-Up Status Reports Screens Status Reports Screen Present Status Select Exit Event History Event History MODULE-0 History Status History Status Report Screens SCC Module Battery Cycle Monitor Module Only System Status Battery Cycle Monitoring Summary Screen System Configuration Screens System Configuration Date Date Screen Time Time Screen Auto Dial Dial Modem Baud Rate Modem Baud Rate Maximum Auto-Retransfer Attempts Retransfer Attempts Remote Monitor Alarm Limit Settings Screen Alarm Settings Product Load Transfer Procedures Screen Refer to 3.3.2 Load Transfer Procedures for more details Start-Up Procedures Screen Refer to 3.3.1 Start-Up Procedure for more details Module Start- Up Procedures Screen Shutdown Procedures Screen Shutdown Procedures Module Shutdown Procedures Screen Battery Time Screen Module Only VDC Battery Time Screen Example 45 Minute Discharge Range of Values for Calculated Battery Times Aining Rem Tim Calculated La p s e d T im e M in u te s Meter Calibration Screen UP Cursor UP Down Cursor Down Select Choose Battery Equalize Screen Battery Equalize Recharging Alarm and Status Messages Module Status Messages 3 Modules Connected System Status Messages Load Block Messages Abbreviations Used in Alarm Messages OF/UF DC Ground Fault Battery CB OpenPower Battery Manual Reset Static SwitchBypass Phase Control Power Alarm Indications and Other Alarms That Activate Summary AlarmsSystem Configuration Screens or the watchdog timer has Reverse Power Temperature Over-TemperatureTimeout System Configuration Screens Load On UPS Alarm Message Special Functions Communication Interfaces Worldwide ReportingAuto-Dial Requesting Information Local Reporting to a Terminal Local Reporting to a MonitorSite Reporting SiteScan or Snmp Remote Monitor Panel Separate / Simultaneous Outputs Load On Bypass Scct OK To Transfer Load on Bypass UPS Available Load on UPS Bypass Available Momentary Overloads Refer to 3.4 Automatic Operations Input Power Failure Load On Battery Input Power Fail Load on Battery One Module Off-Line One Module Off-Line Load on UPS Off Battery Load on UPS Battery Not Available Refer to 3.3.3 Shutdown Procedures Emergency Modules Off Emergency Power Off Emergency Power Off Refer to 3.2.10 Maintenance Bypass System Shutdown Load on Maintenance Bypass Two Breakers Load on Maintenance Bypass Three Breakers Manual Procedures Refer to 3.4 Automatic Operations for more details Start-Up Procedure SCC Start-Up B2. Set the Static Switch Disconnects OFF open SCC Start-Up Procedures Screen UPS Module Start-Up Module Start-Up Procedures Screen Product Load Transfer Procedures Maintenance Bypass Load Transfers Maintenance BypassIf the load is on Maintenance Bypass System Bypass Shutdown Procedures System Shutdown Procedure UPS bypass line is still energized 100 Module Shutdown Procedure Remote Emergency Power Off Repo Local Emergency Modules Off Lemo Automatic Operations Overloads Without Transfer Automatic Transfers to Bypass Automatic Retransfers to UPS Automatic Module Off-Line Automatic Emergency Modules Off Maintenance DIS Product Liebert Global Services Maintenance Agreements The Signature ProgramProfessional Start-Up Training Air Filters Routine MaintenanceRecord Log Battery Maintenance Battery Safety Precautions DIS Product 112 DIS Product Matching Battery Cabinets Optional Power BatteriesRack-Mounted Batteries Torque Requirements Torque Specifications Unless Otherwise Labeled Detection of Trouble Recommended Test Equipment Reporting a ProblemCorrective Actions Rating Environmental Conditions Adjustments Battery Operation Electrical Specifications Voltage Adjustment Range Phase BalancingVoltage Transient Recovery Time Voltage Harmonic Content Series 600T UPS