23x0# show ap config | Nortel Networks 2300 guide

			Configuring User Encryption 219

		success: change accepted.
23x0# show ap config
Port	4: AP model: AP-241, POE:		enable, bias: high, name: AP04
		boot-download-enable:	YES
		load balancing group:	none
Radio 1: type: 802.11a, mode:			enabled, channel: 36
tx pwr:		1, profile: rp3
auto-tune max-power: default, min-client-rate: 5.5, max-retransmissions: 10
Port	6: AP model: MP-252, POE:		enable, bias: high, name: AP06
		boot-download-enable:	YES
		load balancing group:	none
Radio 1: type: 802.11g, mode:			enabled, channel: 6
tx pwr:		1, profile: rp3

auto-tune max-power: default, min-client-rate: 5.5, max-retransmissions: 10

Radio 2: type: 802.11a, mode: enabled, channel: 36

tx pwr: 1, profile: rp3

auto-tune max-power: default, min-client-rate: 24, max-retransmissions: 10

14Save the configuration. Type the following command:

23x0# save config

success: configuration saved.

Nortel WLAN Security Switch 2300 Series Configuration Guide

Image 219

Nortel Networks 2300 manual 23x0# show ap config

Contents

Nortel Wlan Security Switch 2300 Series Configuration Guide Statement of conditions Copyright Nortel Networks Limited 2005. All rights reservedTrademarks Restricted rights legend Nortel Inc. software license agreement USA requirements only Legal Information Limited Product Warranty Limited Warranty Software License Agreement Nortel Wlan Security Switch 2300 Series Configuration Guide SSH Source Code Statement OpenSSL Project License Statements Class a Statement RF Radiation Hazard Warning Deployment Statement 320657-A Contents Configuring and Managing Ports and VLANs Configuring and Managing IP Interfaces and Services Configuring Snmp Configuring and Managing Mobility Domain Roaming Configuring AP access points Wi-Fi Multimedia Configuring and Managing Igmp Snooping Managing Keys and Certificates Configuring AAA for Network Users Configuring Communication with Radius Managing 802.1X on the WSS Switch Managing System Files Troubleshooting a WS Switch Supported Radius Attributes Contents 320657-A How to get Help Getting Help over the phone from a Nortel Solutions CenterGetting Help from the Nortel Web site Getting Help through a Nortel distributor or reseller Nortel Wlan 2300 System Introducing the Nortel Wlan 2300 System Documentation Planning, Configuration, and Deployment Safety and Advisory Notices Menu Name Command Text and Syntax ConventionsBold text CLI Conventions Using the Command-Line Interface NT-mm-nnnnnn Command Prompts Clear fdb dynamic port port-list vlan vlan-id Set port enable disable port-listSyntax Notation Clear interface vlan-idip Text Entry Conventions and Allowed Characters MAC Address NotationIP Address and Mask Notation 0001 User Wildcards, MAC Address Wildcards, and Vlan WildcardsUser Wildcards MAC Address Wildcards Vlan Wildcards Matching Order for Wildcards000102 00010203 0001020304 23x0# show port poe 1,2,4,13 23x0# set port enable23x0# reset port Port Lists Virtual LAN Identification Command-Line Editing Keyboard Shortcuts Function Keyboard Shortcuts History Buffer Tabs Single-Asterisk * Wildcard Character Double-Asterisk ** Wildcard Characters Using CLI Help 23x0# help Commands23x0# show i? Set ap dap name Understanding Command DescriptionsServer Status Port Enabled 23x0# show ip telnet Overview of AAA for Administrative and Local Access Configuring AAA for Administrative and Local Access Configuring AAA for Administrative and Local Access Typical Nortel Wlan 2300 System Before You Start About Administrative Access Access Modes Types of Administrative Access First-Time Configuration using the Console Username Enabling an AdministratorPassword 23x0 enable 23x0# set enablepass Setting the WSS Switch Enable PasswordSetting the WSS Enable Password for the First Time WMS Enable Password Configuring AAA for Administrative and Local Access 23x0# set authentication console * local Authenticating at the Console Customizing AAA with Wildcards and Groups Setting User Passwords Success User Jose created Configuring Accounting for Administrative UsersAdding and Clearing Local Users for Administrative Access Set user username password password 23x0# show accounting statistics 23x0# show aaa Displaying the AAA ConfigurationSaving the Configuration 23x0# save config configday Administrative AAA Configuration Scenarios Local Authentication 23x0# set server group sg1 members r1 Success change accepted Local Override and Backup Local Authentication Authentication When Radius Servers Do Not Respond Configuring and Managing Ports Configuring and Managing Ports and VLANs Vlan Setting the Port Type Show version WSS 2380 40 AP Software License Upgrade Setting a Port for a Directly Connected AP access port 23x0# set port type ap 4-6 model 2330 poe enable Setting a Port for a Wired Authentication User Configuring for a Distributed AP 23x0# set port type wired-auth Clearing a PortClear port type port-list Clearing a Distributed AP 23x0# clear port typeClear dap dap-num Configuring a Port Name Setting a Port NameRemoving a Port Name RJ45 Set port preference port-listrj45Clear port preference port-list Show port preference port-list Configuring Port Operating Parameters 10/100 Ports-Autonegotiation and Port SpeedGigabit Ports-Autonegotiation and Flow Control Disabling or Reenabling a Port Disabling or Reenabling Power over Ethernet Resetting a Port Set port poe port-listenable disableReset port port-list Show port status port-list Displaying Port Configuration and StatusDisplaying Port Information Displaying PoE State Displaying Port Statistics Clearing Statistics CountersMonitoring Port Statistics 23x0# monitor port counters Link Redundancy Configuring Load-Sharing Port GroupsConfiguring a Port Group Load Sharing Interoperating with Cisco Systems EtherChannel Configuring and Managing VLANsRemoving a Port Group Displaying Port Group Information Understanding VLANs in Nortel WSS Software VLANs, IP Subnets, and IP AddressingUsers and VLANs Vlan Names Roaming and VLANsTraffic Forwarding Tunnel Affinity 802.1Q Tagging Set vlan vlan-numname name Configuring a VlanCreating a Vlan Adding Ports to a Vlan 23x0# clear vlan marigold port 13 tag Removing an Entire Vlan or a Vlan Port23x0# set vlan red port 9-11,21 23x0# clear vlan red port 23x0# clear vlan ecru Set vlan vlan-idtunnel-affinity num Changing Tunneling Affinity Displaying Vlan Information Show vlan config vlan-id23x0# show vlan config burgundy Managing the Layer 2 Forwarding Database Types of Forwarding Database Entries How Entries Enter the Forwarding Database Show fdb count perm static dynamic vlan vlan-id Displaying Forwarding Database InformationDisplaying the Size of the Forwarding Database Displaying Forwarding Database Entries 23x0# set fdb static 002b3c4d5e6f port 1 vlan default Adding an Entry to the Forwarding Database23x0# set fdb perm 00bbccddeeff port 3,5 vlan blue Removing Entries from the Forwarding Database 23x0# clear fdb dynamic23x0# clear fdb port 3,5 Changing the Aging Timeout Period Port and Vlan Configuration ScenarioConfiguring the Aging Timeout Period Displaying the Aging Timeout Period 23x0# set system countrycode US 23x0# set port 6 name confroom123x0# set port 7 name confroom2 23x0# set port 8-13 name manufacturing MAC 23x0# set port type ap 2-16 model 2330 poe enable Port group backbonelink is up Ports 22 23x0# set port type wired-auth 17,18 Save the configuration. Type the following command MTU Support Configuring and Managing IP Interfaces and Services Configuring and Managing IP Interfaces Statically Configuring an IP Interface Adding an IP InterfaceEnabling the Dhcp Client Set interface vlan-idip dhcp-client enable disable 23x0# set interface corpvlan ip dhcp-client enable23x0# show interface 23x0# show dhcp-client Interface Corpvlan4 Configuration Status Enabled Dhcp State Set interface vlan-idstatus up down Disabling or Reenabling an IP Interface Removing an IP Interface Configuring the System IP Address Displaying IP Interface InformationShow interface vlan-id Set system ip-address ip-addr Designating the System IP Address Show system Displaying the System IP Address Configuring and Managing IP Routes Clearing the System IP AddressClear system ip-address Configuring and Managing IP Interfaces and Services 320657-A Displaying IP Routes Show ip route destination23x0# show ip route 224.0.0.0/ 4 IP Local 23x0# set ip route default 10.5.4.1 Adding a Static Route23x0# set ip route 192.168.4.0 255.255.255.0 10.5.4.2 23x0# clear ip route 192.168.4.69/24 Managing the Management Services23x0# clear ip route default Removing a Static Route Enabling SSH Login TimeoutsSession Timeouts Managing SSH 23x0# show crypto key ssh ec6f567fd1fdc02893aea4f97cf51304 Changing the SSH Service Port NumberAdding an SSH User Show crypto key ssh 23x0# clear sessions admin ssh Changing SSH TimeoutsShow sessions admin Clear sessions admin ssh session-id 23x0# show sessions admin Adding a Telnet User Telnet Login TimersManaging Telnet Enabling Telnet Changing the Telnet Service Port Number Resetting the Telnet Service Port Number to Its DefaultManaging Telnet Server Sessions Displaying Https Information Configuring and Managing DNSManaging Https Enabling Https Configuring and Managing IP Interfaces and Services Enabling or Disabling the DNS Client Set ip dns enable disable Set ip dns server ip-addrprimary secondary Configuring DNS ServersAdding a DNS Server Removing a DNS Server Set ip dns domain name Configuring a Default Domain NameAdding the Default Domain Name Removing the Default Domain Name 23x0# show ip dns Configuring and Managing AliasesDisplaying DNS Server Information Show ip dns Adding an Alias Set ip alias name ip-addr23x0# set ip alias HR1 Clear ip alias name Removing an Alias 23x0# show ip alias Configuring and Managing Time ParametersDisplaying Aliases Show ip alias name Setting the Time Zone Displaying the Time ZoneClearing the Time Zone Configuring the Summertime Period Displaying the Summertime PeriodClearing the Summertime Period Time now is Sun Feb 29 2004, 235802 PST Statically Configuring the System Time and DateSet timedate date mmm dd yyyy time hhmmss 23x0# set timedate date feb 29 2004 time Show timedate 23x0# show timedate Displaying the Time and Date Configuring and Managing NTP Adding an NTP Server Set ntp server ip-addr23x0# set ntp server Clear ntp server ip-addrall Removing an NTP Server Changing the NTP Update Interval Set ntp update-interval seconds23x0# set ntp update-interval Clear ntp update-interval Resetting the Update Interval to the Default Enabling the NTP Client Set ntp enable disable Managing the ARP Table Displaying NTP InformationShow ntp Displaying ARP Table Entries Show arp ip-addr23x0# show arp Success added arp 10.10.10.1 at 00bbccddeeff on Vlan Adding an ARP EntrySet arp permanent static dynamic ip-addrmac-addr 23x0# set arp static 10.10.10.1 00bbccddeeff 23x0# set arp agingtime Changing the Aging TimeoutPinging Another Device Set arp agingtime seconds 23x0# clear sessions telnet client Logging In to a Remote Device23x0# telnet 23x0# show sessions telnet client IP Interfaces and Services Configuration Scenario Tracing a Route23x0# traceroute server1 23x0# set ip route default 10.20.10.1 23x0# set system ip-address23x0# set ip dns server 10.10.10.69 Primary 23x0 # show ip dns 23x0# set ip dns enableSummertime is enabled, and set to PDT 23x0# set ip dns server 10.20.10.69 Secondary Configuring Snmp Configuring SnmpOverview 23x0# set system location 3rdfloorcloset Setting the System Location and Contact Strings23x0# set system contact sysadmin1 Set system location string set system contact string Set snmp protocol v1 v2c usm all enable disable 23x023x0# set snmp protocol all enableEnabling Snmp Versions Clear snmp community name comm-string Configuring Community Strings SNMPv1 and SNMPv2c Only Clear snmp usm usm-username Creating a USM User for SNMPv3 23x0# set snmp usm snmpmgr1 snmp-engine-id local Command Examples 23x0# set snmp security encrypted Setting Snmp Security Clear snmp profile profile-name Configuring a Notification Profile 23x0# set snmp notify profile default send all Configuring Snmp Configuring a Notification Target Security unsecured authenticated encryptedClear snmp notify target target-num 23x0# set snmp notify target 2 10.10.40.10 v1 trap Displaying Snmp Information Enabling the Snmp ServiceSet ip snmp server enable disable 23x0# set ip snmp server enable Displaying Snmp Version and Status Information Displaying the Configured Snmp Community Strings Displaying USM Settings Displaying Notification Profiles 23x0# show snmp notify profile insert updated example Displaying Notification Targets 23x0# show snmp notify target insert updated example Displaying Snmp Statistics Counters Configuring Snmp 320657-A About the Mobility Domain Feature Configuring and Managing Mobility Domain Roaming Configuring a Mobility Domain Configuring the Seed Set mobility-domain mode seed domain-name mob-domain-name23x0# set mobility-domain mode seed domain-name Pleasanton Set mobility-domain member ip-addr Configuring Member WSSs on the Seed Configuring a Member Set mobility-domain mode member seed-ip ip-addr23x0# set mobility-domain mode member seed-ip 192.168.15.5 Displaying Mobility Domain Status2370# show mobility-domain status 192.168.14.6 Displaying the Mobility Domain Configuration 2370# show mobility-domain configThis WSS is a member, with seed 2370# clear mobility-domain Clearing a Mobility Domain from a WSS Clear mobility-domain member ip-addr Clearing a Mobility Domain Member from a Seed 23x0# show roaming station Displaying Roaming Stations Displaying Roaming VLANs and Their Affinities 23x0 # show roaming vlanAffinity State Port Understanding the Sessions of Roaming UsersDisplaying Tunnel Information 23x0 # show tunnel Active Requirements for Roaming to Succeed Effects of Timers on Roaming 23x0# set mobility-domain member seed-ip Mobility Domain ScenarioMonitoring Roaming Sessions WSS-20show sessions network verbose 23x0# show mobility-domain config 23x0# show roaming vlan23x0# show tunnel Configuring User Encryption Wireless Encryption Defaults Default Encryption Configuring WPA WPA Cipher Suites WPA Encryption with Tkip Only WPA Encryption with Tkip and WEP Tkip Countermeasures WPA Authentication Methods WPA Information Element Client Support Supported Encryption Support for WPA and Non-WPA Clients Specifying the WPA Cipher Suites Configuring WPACreating a Service Profile for WPA Enabling WPA Enabling PSK Authentication Changing the Tkip Countermeasures Timer Value Set service-profile name psk-raw hex Set service-profile name auth-psk enable disable23x0# set service-profile wpa auth-psk enable Set service-profile name psk-phrase passphrase Set radio-profile name service-profile name Displaying WPA SettingsShow service-profile name ? 23x0# show service-profile wpa Specifying the RSN Cipher Suites Configuring RSNCreating a Service Profile for RSN Enabling RSN 23x0# set service-profile rsn cipher-ccmp enable Displaying RSN Settings 23x0# set radio-profile blgd2 service-profile rsn Configuring WEP Encryption for Dynamic and Static WEP Set service-profile name wep key-index num key value Setting Static WEP Key Values Encryption Configuration Scenarios 23x0# set service-profile wepsrvc4 wep active-unicast-indexAssigning Static WEP Keys Enabling WPA with Tkip 23x0# set service-profile wpa success change accepted 23x0# show ap config Enabling Dynamic WEP in a WPA Network 23x0# set service-profile wpa-wep success change accepted23x0# show service-profile wpa-wep 23x0# set ap 5,11 radio 1 radio-profile rp2 mode enable Success change accepted 23x0# set service-profile wpa-wep-for-mac Configuring Encryption for MAC Clients 23x0# show service-profile wpa-wep-for-mac 23x0# show ap config Configuring User Encryption 320657-A AP Overview Configuring AP access points Example Nortel Network Country of Operation Distributed AP Network Requirements Directly Connected APs and Distributed APs Distributed APs and Dhcp Option Distributed APs and STP AP Parameters NameBias High Group Upgrade-firmware EnableDisable Resiliency and Dual-Homing Options for APs Dual-Homed Direct Connections to a Single WSS Dual-Homed Direct and Distributed Connections to WSSs Dual-Homed Distributed Connections to WSSs on Both AP Ports Dual-Homed Distributed Connections to WSSs on One AP Port AP Boot Process Configuring AP access points Configuring AP access points Configuring AP access points Example AP Boot over Layer 2 Network Example AP Boot over Layer 3 Network Example Boot of Dual-Homed AP Dual-Homed AP Booting Session Load Balancing Service Profiles Public and Private SSIDs Encryption Dap status command Configuring AP access points Radio Profiles Default Radio Profile RF Auto-Tuning Antennatype Internal Nortel external antenna model Tx-powerRadio-Specific Parameters Channel Configuring AP access points Set system countrycode code Specifying the Country of Operation WSS 23x0# show system How an Unconfigured AP Finds an WSS Switch To Configure It Configuring a Template for Automatic AP Configuration Radio 2 type 802.11a, mode enabled, channel dynamic Configured APs Have Precedence Over Unconfigured APsConfiguring a Template 23x0# show dap config auto Changing AP Parameter Values 23x0# set dap auto mode enable 23x0# set dap auto radio 1 radio-profile autodap123x0# show dap status auto Set dap auto persistent dap-numall Setting the Port Type for a Directly Connected AP Configuring AP Port Parameters Port parameter Setting 23x0# set port type ap 11-14,16 model 2330 poe enable Configuring an Indirectly Connected AP Changing AP Names Clearing an AP from the Configuration Changing Bias Configuring a Load-Balancing GroupDisabling or Reenabling Automatic Firmware Upgrades Enabling LED Blink Mode RSA aaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaa Configuring AP-WSS SecurityEncryption Key Fingerprint Encryption Options 23x0# show dap status Confirming an AP’s Fingerprint on an WSS Switch 23x0# set dap security require Setting the AP Security Requirement on an WSS SwitchSet dap num fingerprint hex Set dap security require optional Fingerprint Log Message Disabling or Reenabling Beaconing of an Ssid Configuring a Service ProfileChanging the Fallthru Authentication Type Disabling or Reenabling Encryption for an Ssid Configuring AP access points Changing Radio Parameters Configuring a Radio ProfileSet radio-profile name mode enable disable Creating a New Profile 23x0# set radio-profile rp1 dtim-interval Set radio-profile name beacon-interval interval23x0# set radio-profile rp1 beacon-interval Set radio-profile name dtim-interval interval 23x0# set radio-profile rp1 frag-threshold Set radio-profile name rts-threshold threshold23x0# set radio-profile rp1 rts-threshold Set radio-profile name frag-threshold threshold 23x0# set radio-profile rp1 max-tx-lifetime Set radio-profile name max-rx-lifetime time23x0# set radio-profile rp1 max-rx-lifetime Set radio-profile name max-tx-lifetime time 23x0# set radio-profile rplong preamble-length long Set radio-profile name 11g-only enable disable23x0# set radio-profile rp1 11g-only enable Set radio-profile name preamble-length long short Clear radio-profile name Resetting a Radio Profile Parameter to its Default ValueRemoving a Radio Profile Clear radio-profile name parameter Configuring the Channel and Transmit Power Configuring Radio-Specific Parameters Configuring the External Antenna Model 23x0# set ap 11 radio 1 channel 1 tx-power23x0# set ap 5 radio 2 channel 36 tx-power 23x0# set dap 1 radio 1 antennatype ANT1060 23x0# set radio-profile rp2 service-profile wpaclients Mapping the Radio Profile to Service Profiles Assigning a Radio Profile and Enabling Radios 23x0# set ap 11-14,16 radio 2 radio-profile rp1 mode enable23x0# set ap 6 radio 1 radio-profile rp1 mode disable Disabling or Reenabling Radios Set ap port-listdap dap-numradio 1 2 mode enable disable 23x0# set ap 3,7 radio 2 mode disableEnabling or Disabling Individual Radios Disabling or Reenabling All Radios Using a Profile 23x0# set radio-profile rp1 mode enable23x0# set radio-profile rp1 mode disable Resetting a Radio to its Factory Default Settings Clear ap port-listdap dap-numradio 1 2 all23x0# clear ap 3 radio Restarting an AP Displaying AP Information 23x0# show dap config Displaying AP Configuration Information Displaying a List of Distributed APs Show dap global dap-numserial-id serial-ID23x0 # show dap global 23x0 # show dap unconfigured Show dap unconfigured Show dap connection dap-numserial-id serial-ID Displaying Connection Information for Distributed APs 23x0 # show service-profile wpaclients Displaying Service Profile Information 23x0 # show radio-profile default Displaying Radio Profile InformationShow radio-profile name ? Displaying AP Status Information 23x0 # show ap counters Displaying AP Statistics Counters 116665 7694 11643396 629107 112115 3368239 142900 Totl RF Auto-Tuning Overview Configuring RF Auto-Tuning Initial Channel and Power Assignment Channel and Power Tuning Power TuningChannel Tuning Tuning the Transmit Data Rate RF Auto-Tuning Parameters Min-client-rate For 802.11b For 802.11a Changing RF Auto-Tuning Settings Changing the Channel Holddown Interval Changing Channel Tuning SettingsDisabling or Reenabling Channel Tuning Changing the Channel Tuning Interval Changing the Power Backoff Interval Changing Power Tuning SettingsEnabling Power Tuning Changing the Power Tuning Interval 23x0# set ap 7 radio 1 auto-tune max-power Changing the Client Retransmission Threshold23x0# set ap 7 radio 1 auto-tune max-retransmissions Changing the Minimum Transmit Data Rate Displaying RF Auto-Tuning Information Displaying RF Auto-Tuning Settings 23x0# show radio-profile default23x0# show ap config 2 radio 23x0# show auto-tune neighbors ap 2 radio Displaying RF Neighbors 23x0# show auto-tune attributes ap 2 radio Displaying RF Attributes Configuring RF Auto-Tuning 320657-A How WMM Works in WSS Software Wi-Fi Multimedia QoS on the WSS Switch WMM in a Nortel Network QoS on an AP Set radio-profile name wmm enable disable Disabling or Reenabling WMMWMM Priority Mappings 23x0# show dap qos-stats Displaying WMM Information23x0# show radio-profile radprof1 Show dap qos-stats dap-numshow dap qos-stats port-list Wi-Fi Multimedia Configuring and Managing Spanning Tree Protocol Set spantree enable disable 23x0# set spantree enableEnabling the Spanning Tree Protocol Changing Standard Spanning Tree Parameters Snmp Port Path Cost Defaults Port Priority Changing the Bridge Priority Set spantree priority value all vlan vlan-id23x0# set spantree priority 69 vlan pink Resetting the STP Port Cost to the Default Value Changing STP Port ParametersChanging the STP Port Cost 23x0# set spantree portvlanpri 3-4 priority 48 vlan mauve Resetting the STP Port Priority to the Default ValueChanging the STP Port Priority 23x0# set spantree portpri 3-4 priority Changing the STP Maximum Age Changing Spanning Tree TimersChanging the STP Forwarding Delay Changing the STP Hello Interval 23x0# set spantree maxage 15 all Configuring and Managing STP Fast Convergence Features Uplink Fast Convergence Configuring Port Fast Convergence Set spantree portfast port port-listenable disable23x0# set spantree portfast port 9,11,13 enable 23x0# show spantree portfast Port Vlan Portfast Disable EnableDisplaying Port Fast Convergence Information Show spantree portfast port-list Configuring Backbone Fast Convergence Set spantree backbonefast enable disable23x0# set spantree backbonefast enable 23x0# show spantree backbonefast Backbonefast is enabledDisplaying the Backbone Fast Convergence State Show spantree backbonefast Set spantree uplinkfast enable disable Configuring Uplink Fast Convergence 23x0# show spantree uplinkfast Displaying Spanning Tree InformationDisplaying Uplink Fast Convergence Information Show spantree uplinkfast vlan vlan-id Displaying STP Bridge and Port Information Show spantree port-listvlan vlan-id active23x0# show spantree vlan mauve Port 1 Vlan 1 have path cost Displaying the STP Port Cost on a Vlan BasisShow spantree portvlancost port-list 23x0# show spantree portvlancost 23x0# show spantree blockedports vlan default Displaying Blocked STP PortsShow spantree blockedports vlan vlan-id Displaying Spanning Tree Statistics Show spantree statistics port-listvlan vlan-id23x0# show spantree statistics 1 Bpdu related parameters Delay root port Timer value Timer restarted is Topology change TimerTopology change Timer value Hold timer Hold timer value Delay root port Timer Clear spantree statistics port-listvlan vlan-id Spanning Tree Configuration Scenario23x0# set port disable Clearing STP Statistics 23x0# set port enable Default None Backbone DownSpanning tree mode Disabled 128 Down Auto Network 10/100BaseTx 1000/full Set igmp enable disable vlan vlan-id Disabling or Reenabling Igmp SnoopingDisabling or Reenabling Proxy Reporting Enabling the Pseudo-Querier Changing Igmp TimersSet igmp proxy-report enable disable vlan vlan-id Set igmp querier enable disable vlan vlan-id Set igmp qi seconds vlan vlan-id Changing the Query Interval Set igmp oqi seconds vlan vlan-id Changing the Other-Querier-Present Interval Set igmp qri tenth-seconds vlan vlan-id Changing the Query Response Interval Set igmp lmqi tenth-seconds vlan vlan-id Changing the Last Member Query Interval Set igmp rv num vlan vlan-id Set igmp mrsol enable disable vlan vlan-idEnabling Router Solicitation Changing Robustness Configuring Static Multicast Ports Changing the Router Solicitation IntervalSet igmp mrsol mrsi seconds vlan vlan-id Adding or Removing a Static Multicast Router Port Set igmp mrouter port port-listenable disable Set igmp receiver port port-listenable disable Displaying Multicast InformationAdding or Removing a Static Multicast Receiver Port Show igmp vlan vlan-id 23x0# show igmp vlan orange192.28.7.5 Dvmrp Group Port Receiver-IP Receiver-MAC Clear igmp statistics vlan vlan-id Displaying Multicast Statistics OnlyClearing Multicast Statistics Show igmp statistics vlan vlan-id Querier for vlan orange Port Querier-IP Querier-MAC Displaying Multicast QueriersShow igmp querier vlan vlan-id Show igmp querier vlan orange 192.28.7.5 000102030405 Dvmrp Displaying Multicast RoutersShow igmp mrouter vlan vlan-id Show igmp mrouter vlan orange Displaying Multicast Receivers 23x0# show igmp receiver-table group 237.255.255.0/24Vlan red Session Port Receiver-IP Receiver-MAC Configuring and Managing Igmp Snooping 320657-A About Security Access Control Lists Configuring and Managing Security ACLs Setting Security ACLs Overview of Security ACL Commands Security ACL Filters Creating and Committing a Security ACL Setting a Source IP ACL Common IP Protocol Numbers23x0# set security acl ip acl-1 permit 192.168.1.4 Class of Service Class-of-Service CoS Packet HandlingWildcard Masks Configuring and Managing Security ACLs Common Icmp Message Types and Codes Setting an Icmp ACL Common Icmp Message Types and Codes Setting TCP and UDP ACLs Setting a TCP ACLSetting a UDP ACL Configuring and Managing Security ACLs Determining the ACE Order Committing a Security ACL 23x0# commit security acl acl-9923x0# commit security acl all Viewing Security ACL Details Viewing Security ACL InformationViewing the Edit Buffer Viewing Committed Security ACLs 23x0# show security acl hits ACL hit-counters Displaying Security ACL Hits Mapping Security ACLs Clearing Security ACLs23x0# clear security acl acl-99 Mapping User-Based Security ACLs 23x0# commit security acl acl-222 success change accepted23x0# set user Natasha attr filter-id acl-222.in Configuring and Managing Security ACLs 23x0# show security acl map acl-999 Displaying ACL Maps to Ports, VLANs, and Virtual PortsClearing a Security ACL Map 23x0# set security acl map acl-222 port 2 tag 1-3,5 23x0# clear security acl map acljoe port 4 Modifying a Security ACL23x0# show security acl map acljoe ACL acljoe is mapped to 23x0# show security acl info all Adding Another ACE to a Security ACL Placing One ACE before Another Modifying an Existing Security ACL Type Status Acl-a Not Committed Acl-111 Clearing Security ACLs from the Edit Buffer23x0# show security acl editbuffer ACL edit-buffer table Using ACLs to Change CoS 23x0# rollback security acl acl-111ACL edit-buffer information for all Filtering Based on Dscp Values 23x0# set security acl map voip vlan corpvlan out Enabling Prioritization for Legacy Voice over IP23x0# set security acl ip voip permit 0.0.0.0 23x0# commit security acl voip Enabling SVP Optimization for SpectraLink Phones Security ACL Configuration Scenario 23x0# save config Managing Keys Certificates Why Use Keys and Certificates? Wireless Security through TLS PEAP-MS-CHAP-V2 Security About Keys and Certificates Public Key Infrastructures Public and Private Keys Digital Certificates Pkcs Object Files Supported by Nortel Crypto generate key commandCreating Keys and Certificates Pkcs #7, Pkcs #10, and Pkcs #12 Object Files Managing Keys and Certificates Procedures for Creating and Validating Certificates Creating Public-Private Key Pairs Crypto generate key admin eap ssh webaaa 512 102423x0# crypto generate key admin Admin key pair generated Crypto generate self-signed admin eap webaaa 23x0# crypto generate self-signed admin Country Name USGenerating Self-Signed Certificates Crypto pkcs12 admin eap webaaa filename Crypto otp admin eap webaaa one-time-password 23x0# crypto generate request admin Begin Certificate Installing a CA’s Own Certificate Key and Certificate Configuration Scenarios 23x0# show crypto certificate admin CertificateDisplaying Certificate and Key Information ENDCERTIFICATE-----23x0#crypto generate self-signed eap 23x0# crypto generate self-signed adminSelf-signed cert for admin is Creating Self-Signed Certificates 23x0# show crypto certificate admin 20# crypto generate self-signed webaaa Country Name US23x0# show crypto certificate eap 23x0# show crypto certificate webaaa Certificate 23x0# copy tftp//192.168.253.1/20481x.p12 20481x.p12 23x0# crypto otp admin SeC%#6@o%c23x0# crypto pkcs12 admin 2048admn.p12 23x0# copy tftp//192.168.253.1/2048admn.p12 2048admn.p12 Keypair Device certificate CA certificate Unstructured Name wiring closet 12 CSR for admin is Email Address admin@example.com Enter PEM-encoded certificate 23x0# crypto certificate admin23x0# crypto ca-certificate admin 23x0# show crypto ca-certificate admin About AAA for Network Users Configuring AAA for Network Users Authentication Types Authentication Authentication Algorithm Authentication Flowchart for Network Users To 802.1X? Yes Ssid Name Any Last-Resort ProcessingUser Credential Requirements Configuring AAA for Network Users CLI Authorization Accounting AAA Tools for Network Users Summary of AAA Features Wildcard Any for Ssid Matching Wildcards and Groups for Network User Classification AAA Methods for Ieee 802.1X and Web Network Access AAA Rollover ProcessLocal Override Exception Remote Authentication with Local Backup Remote Pass-Through or Local Authentication EAP-MD5 Ieee 802.1X Extensible Authentication Protocol Types Ways an WSS Switch Can Use EAP Effects of Authentication Type on Encryption Method Configuring 802.1X Authentication Configuring 802.1X Acceleration Using Pass-Through Authenticating through a Local Database Binding User Authentication to Machine Authentication Authentication Rule Requirements Clear dot1x bonded-period Bonded Authentication PeriodBonded Authentication Configuration Example Set dot1x bonded-period seconds Displaying Bonded Authentication Configuration Information Show dot1x config 23x0# show dot1x config23x0# set dot1x bonded-period Configuring Authentication and Authorization by MAC Address Adding and Clearing MAC Users and User Groups Locally Adding MAC Users and GroupsClearing MAC Users and Groups 23x0# set mac-user 000102030405 attr vlan-name red Configuring MAC Authentication and Authorization23x0# set authentication mac ssid voice 010102030405 local 23x0# set authentication mac ssid voice 010102* local 23x0# set radius server bigbird author-password h00per Configuring Web-based AAAChanging the MAC Authorization Password for Radius Set radius server server-nameauthor-password password How Portal Web-based AAA Works WSS Requirements Web-based AAA Requirements and Recommendations Configuring AAA for Network Users Client Web Browser Recommendations WSS RecommendationsClient NIC Requirements Client Web Browser Requirements Configuring Portal Web-based AAA Portal Web-based AAA Configuration Example23x0# set user web-portal-mycorp attr vlan-name corpvlan 23x0# show sessions network ssid mycorp 23x0# show config 23x0# show sessions network ssid mycorp Using a Custom Login Copying and Modifying the Nortel Login Custom Login Page ScenarioTitleMy Corp webAAA/title 23x0# dir mycorp-webaaa H3Welcome to Mycorp’s Wireless LAN/h3BWARNING/b My corp’s warning text 23x0# mkdir mycorp-webaaa success change accepted Variables for Redirect URLs Description Using Dynamic Fields in Web-based AAA Redirect URLs Configuring Last-Resort Access WSS Switch Serving as Radius Proxy Configuring AAA for Users of Third-Party APs Authentication Process for 802.1X Users of a Third-Party AP WSS Switch Requirements RequirementsThird-Party AP Requirements Set radius proxy port port-listtag tag-valuessid ssid-name Set authentication mac wired mac-addr-wildcard method123x0# set port type wired-auth 3-4 tag 23x0# set authentication mac wired aabbcc010101 srvrgrp1 23x0# set radius proxy client address 10.20.20.9 key radkey1 23x0# set authentication proxy ssid mycorp ** srvrgrp1 End-date Assigning Authorization Attributes Filter-id Idle-timeoutService-type Session-timeout Ssid Start-dateTime-of-day Vlan-name Url Assigning Attributes to Users and Groups 23x0# set usergroup eastcoasters attr filter-id acl-101.in Assigning a Security ACL to a User or a GroupAssigning a Security ACL Locally 23x0# set user Jose attr filter-id acl-101.in Assigning a Security ACL on a Radius Server Clear mac-usergroup groupname attr filter-id Clearing a Security ACL from a User or Group Assigning Encryption Types to Wireless Users Assigning and Clearing Encryption Types Locally23x0# set mac-usergroup mac-fans attr encryption-type Assigning and Clearing Encryption Types on a Radius Server About the Location Policy How the Location Policy Differs from a Security ACL Setting the Location Policy Applying Security ACLs in a Location Policy Rule23x0# set location policy deny if user eq *.theirfirm.com WSS-20show location policy Displaying and Positioning Location Policy Rules Configuring Accounting for Wireless Network Users Set accounting admin console dot1x mac webClear location policy rule-number Configuring AAA for Network Users Viewing Local Accounting Records May 21 Acct-Status-Type=STOP Acct-Authentic=2 Viewing Roaming Accounting RecordsWSS-20-0013#show accounting statistics WSS-20-0017#show accounting statistics Rs-4 Set authentication admin Jose sg3Server Addr Ports Rs-3 Vlan-Name = k2 Avoiding AAA Problems in Configuration OrderSet authentication web ssid any ** sg1 Set authentication web ssid corpa ** corpasrvr Configuring AAA for Network Users 23x0# set accounting dot1x ssid mycorp * start-stop group1 Using Authentication and Accounting Rules TogetherConfiguration Producing an Incorrect Processing Order Configuration for a Correct Processing Order 23x0# set mobility-profile name roses-profile port 2-4,7,9 Configuring a Mobility Profile NamePorts ========================= Roses-profile Network User Configuration Scenarios23x0# set mobility-profile mode enable 23x0# show mobility-profile Mobility Profiles Mobility Profiles NamePorts ========================= Tulip General Use of Network User Commands23x0# set user EXAMPLE\username attr filter-id acl-101.in 23x0# show security acl info acl-101 WSS-20save config 23x0# set radius server r1 address 10.1.1.1 key sunny Enabling Radius Pass-Through Authentication Unstructured Name wiring closet Enabling PEAP-MS-CHAP-V2 Authentication23x0# set user Natasha password moon 23x0# set user Natasha attr session-timeout 23x0# set radius server r1 address 10.1.1.1 key starry Enabling PEAP-MS-CHAP-V2 Offload 23x0# set radius server r1 address 10.1.1.1 key starry Overriding AAA-Assigned VLANs Radius Overview Configuring Communication with Radius Configuring Communication with Radius Before You Begin Configuring Radius Servers 23x0# set radius key r8gney Configuring Global Radius DefaultsClear radius deadtime key retransmit timeout 23x0# set radius deadtime Setting the System IP Address as the Source Address 23x0# set radius client system-ip23x0# clear radius client system-ip Set radius server server-nameaddress ip-address key string Configuring Individual Radius Servers Configuring Radius Server Groups Deleting Radius ServersClear radius server server-name Configuring Load Balancing Creating Server GroupsOrdering Server Groups 23x0 # show aaa Set server group group-nameload-balance enableAdding Members to a Server Group Clear server group group-nameload-balance Configuring Communication with Radius Deleting a Server Group Radius and Server Group Configuration Scenario 23x0# set server group shorebirds load-balance enable Managing 802.1X on Wired Authentication Ports Managing 802.1X on WSS Switch Enabling and Disabling 802.1X Globally Set dot1x authcontrol enable disable23x0# set dot1x authcontrol enable Success dot1x authcontrol enabled Managing 802.1X Encryption Keys Setting 802.1X Port Control Enabling 802.1X Key Transmission Set dot1x key-tx enable disable23x0# set dot1x key-tx enable Success dot1x key transmission enabled Success dot1x tx-period set to Configuring 802.1X Key Transmission Time IntervalsSet dot1x tx-period seconds 23x0# set dot1x tx-period Configuring 802.1X WEP Rekeying Configuring the Interval for WEP RekeyingManaging WEP Keys Success dot1x max request set to Setting EAP Retransmission AttemptsManaging 802.1X Client Reauthentication 23x0# set dot1x max-req Success dot1x reauthentication enabled Enabling and Disabling 802.1X ReauthenticationSet dot1x reauth enable disable 23x0# set dot1x reauth enable 23x0# clear dot1x reauth-max Set dot1x reauth-max number-of-attempts23x0# set dot1x reauth-max Success dot1x max reauth set to 23x0# set dot1x reauth-period Setting the 802.1X Reauthentication PeriodSuccess dot1x auth-server timeout set to Set dot1x reauth-period seconds Managing Other Timers Setting the Bonded Authentication PeriodClear dot1x max-req Success dot1x quiet period set to Setting the 802.1X Quiet PeriodSet dot1x quiet-period seconds 23x0# set dot1x quiet-period 23x0# clear dot1x timeout auth-server Setting the 802.1X Timeout for an Authorization ServerSet dot1x timeout auth-server seconds 23x0# set dot1x timeout auth-server Displaying 802.1X Information Setting the 802.1X Timeout for a Client 23x0# show dot1x clients Viewing 802.1X Clients Viewing the 802.1X Configuration 23x0# show dot1x stats Viewing 802.1X Statistics Managing 802.1X on the WSS Switch 320657-A Managing Sessions Displaying and Clearing Administrative SessionsShow sessions admin console telnet client Clear sessions admin console telnet client session-id Displaying and Clearing All Administrative Sessions WSS-20 show sessions admin23x0# clear sessions admin 23x0# clear sessions console Displaying and Clearing an Administrative Console SessionWSS-20 show sessions console Tty Username Time Type Tty0 5310 Console Console session Telnet session Displaying and Clearing Administrative Telnet SessionsTty Username Time Type Tty3 Sshadmin 2099 WSS-20 show sessions telnet User Sess IP or MAC Displaying and Clearing Network SessionsDisplaying and Clearing Client Telnet Sessions 23x0 # show sessions network 761 000bbe154656 none Displaying Verbose Network Session InformationJose@example.com 5125 Vlan-eng 003065168d69 4385 Vlan-wep Clear sessions network user user-wildcard Displaying and Clearing Network Sessions by UsernameShow sessions network user user-wildcard 23x0# show sessions network user E Clear sessions network mac-addr mac-addr-wildcard Displaying and Clearing Network Sessions by MAC AddressShow sessions network mac-addr mac-addr-wildcard Show sessions net mac-addr 01055d7e981a Clear sessions network vlan vlan-wildcard Displaying and Clearing Network Sessions by Vlan NameShow sessions network vlan vlan-wildcard Show sessions network vlan west Displaying and Clearing Network Sessions by Session ID Clear sessions network session-id session-id2370# clear sessions network session-id About System Files Managing System Files 23x0# show version details Displaying Software Version InformationShow version details 23x0# show version W2 N/A Displaying Boot Information 23x0# show bootWorking with Files 23x0# dir old Displaying a List of Files Success sent 365 bytes in 0.401 seconds 910 bytes/sec 23x0# copy floor2WSS tftp//10.1.1.1/floor2WSS-backupCopying a File 23x0# copy floor2WSS tftp//10.1.1.1/floor2WSS 23x0# copy tftp//10.1.1.1/newconfig newconfig 23x0# copy tftp//10.1.1.1/newconfig WSSconfigSuccessreceived9163214bytesin105.939seconds Bytes/sec Delete url 23x0# copy testconfig tftp//10.1.1.1/testconfig23x0# delete testconfig Deleting a File 23x0# mkdir corp2 Creating a Subdirectory Managing Configuration Files Removing a Subdirectory23x0# rmdir corp2 Displaying the Running Configuration Show config area area all23x0# show config area vlan Managing System Files Success configuration saved to newconfig Saving Configuration ChangesSave config filename 23x0# save config newconfig Set boot configuration-file filename 23x0# set boot configuration-file floor2WSSSuccess boot config set Loading a Configuration File Load config url23x0# load config newconfig Backing Up and Restoring the System Resetting to the Factory Default Configuration Managing System Files Managing Configuration Changes Upgrading the System Image Backup and Restore Examples23x0# backup system tftp/10.10.20.9/sysabak critical 23x0# restore system tftp/10.10.20.9/sysabak Managing System Files 320657-A About Rogues and RF Detection Rogue Detection Countermeasures Rogue access points and Clients Rogue ClassificationRogue Detection Lists Rogue Detection and Countermeasures Rogue Detection Algorithm Dynamic Frequency Selection DFS RF Detection Scans Countermeasures Summary of Rogue Detection Features Configuring Rogue Detection Lists 23x0# show rfdetect vendor-list Total number of entries Configuring a Permitted Vendor ListSet rfdetect vendor-list client ap mac-addr Show rfdetect vendor-list 23x0# show rfdetect ssid-list Total number of entries Configuring a Permitted Ssid ListSet rfdetect ssid-list ssid-name Show rfdetect ssid-list 23x0# show rfdetect black-list Configuring a Client Black ListSet rfdetect black-list mac-addr Show rfdetect black-list 23x0# show rfdetect attack-list Configuring an Attack ListSet rfdetect attack-list mac-addr Show rfdetect attack-list Enabling Countermeasures Configuring an Ignore List Enabling AP Signatures Disabling or Reenabling Active Scan IDS and DoS Alerts Set rfdetect log enable disableDisabling or Reenabling Logging of Rogues Enabling Rogue and Countermeasures Notifications Flood Attacks DoS Attacks Netstumbler and Wellenreiter Applications Wireless Bridge Ad-Hoc Network Weak WEP Key Used by Client Disallowed Devices or SSIDs Displaying Statistics Counters IDS and DoS Log Messages IDS Log Message Examples Message Type Displaying RF Detection Information Show rfdetect ignore Show rfdetect attack-list 23x0# show rfdetect clients Displaying Rogue ClientsShow rfdetect clients mac mac-addr 23x0# show rfdetect clients mac 000c4163fd6d Displaying Rogue Detection Counters Show rfdetect counters23x0# show rfdetect counters 23x0# show rfdetect mobility-domain ssid nrtl-webaaa Displaying Ssid or Bssid Information for a Mobility DomainShow rfdetect mobility-domain ssid ssid-namebssid mac-addr 23x0# show rfdetect mobility-domain 23x0# show rfdetect mobility-domain bssid 000b0e0004d1 Displaying RF Detect Data Show rfdetect data23x0 # show rfdetect data 23x0# show rfdetect visible ap 3 radio Displaying the APs Detected by an AP Radio Displaying Countermeasures Information Show rfdetect countermeasures23x0# show rfdetect countermeasures Rogue Detection and Countermeasures 320657-A Appendix a Troubleshooting a WS Switch WSS Setup Problems and Remedies Fixing Common WSS Setup Problems Symptom Diagnosis WSS-2370, WSS-2380, or WSS-2360 Recovering the System PasswordBoot boot OPT+=default WSS-2350 Log Message Components Configuring and Managing the System Log Logging Destinations and Levels Debug Info Logging to the Log Buffer Using Log Commands Logging Messages to a Syslog Server Logging to the Console Changing the Current Telnet Session Defaults Setting Telnet Session Defaults Displaying the Log Configuration Logging to the Trace BufferSaving Trace Messages in a File Tracing Session Manager Activity Using the Trace CommandTracing Authentication Activity Running Traces Tracing 802.1X Sessions Tracing Authorization ActivityDisplaying a Trace Stopping a Trace 23x0# show log trace severity error About Trace ResultsDisplaying Trace Results Copying Trace Results to a Server Clearing the Trace LogList of Trace Areas WSS-2370# show interface Using Show CommandsViewing Vlan Interfaces Viewing AAA Session Statistics 23x0# show fdb Viewing FDB InformationViewing ARP Information Vlan-name = vlan-wep Best Practices for Remote Traffic Monitoring Using Snoop Filters on Radios That Use Active ScanRemotely Monitoring Traffic How Remote Traffic Monitoring Works Appendix a Troubleshooting a WS Switch 23x0# set snoop snoop1 observer 10.10.30.2 snap-length Configuring a Snoop Filter Deleting a Snoop Filter Displaying Configured Snoop FiltersMapping a Snoop Filter to a Radio Editing a Snoop Filter Removing Snoop Filter Mappings Enabling or Disabling a Snoop FilterDisplaying the Snoop Filters Mapped to a Radio Displaying the Snoop Filter Mappings for All Radios Success filter snoop1 enabled 23x0# set snoop snoop1 mode enable stop-after Displaying Remote Traffic Monitoring Statistics Preparing an Observer and Capturing TrafficShow snoop stats filter-namedap-numradio 1 Capturing System Information for Technical Support Displaying Technical Support Information 23x0# copy fortechsupport.gz tftp//tftpserver/filename.gz Sending Information to Nets23x0# show tech-support file fortechsupport Success results saved to fortechsupport.gz Appendix a Troubleshooting a WS Switch 320657-A Supported Standard and Extended Attributes Appendix B Supported Radius Attributes 801.1X Attributes 801.1X Attributes Radius Nortel Vendor-Specific Attributes Nortel VSAs Protocol Port Function Appendix C Mobility Domain Traffic Ports Appendix C Mobility Domain Traffic Ports 320657-A Appendix D Dhcp Server How the WSS Software Dhcp Server Works Configuring the Dhcp Server Displaying Dhcp Server Information Show dhcp-server interface vlan-id verbose23x0# show dhcp-server Appendix D Dhcp Server Glossary Advanced Encryption Standard See AES Authentication, authorization, and accounting See AAA CBC-MAC See Ccmp Cyclic redundancy check See CRC Glossary EAP with Transport Layer Security See EAP-TLS Group master key See GMK Group transient key See GTK Industry Canada See IC Information element See WPA IE Media access control address See MAC address Microsoft Challenge Handshake Authentication Per-VLAN Spanning Tree protocol See PVST+ Port address translation See PAT Power over Ethernet See PoE Quality of service See QoS Remote Authentication Dial-In User Service See Radius Spanning Tree Protocol See STP Temporal Key Integrity Protocol See Tkip Type, length, and value See TLV Wisp WPA information element See WPA IE Glossary 320657-A Numerics Index Index Index DNS Enable password Description Subnet masks for, notation conventions System IP address 366 To ports, VLANs, or virtual ports 368 Index Radius Https Index Configuring 341 rogue access points detecting TCP Snmp STP Uplink fast convergence Index WMS Index 320657-A Command Index Command Index Set dap auto radiotype Command Index Command Index 324 Show spantree blockedports 329