23x0# show service-profile wpa-wep-for-mac | Nortel Networks 2300

218Configuring User Encryption

success: change accepted.

6Set the SSID in the service profile to voice. Type the following command:

23x0# set service-profile wpa-wep-for-mac ssid-name voice success: change accepted.

7Enable WPA in service profile wpa-wep-for-mac. Type the following command:

23x0# set service-profile wpa-wep-for-mac wpa-ie enable success: change accepted.

8Enable the WEP40 cipher suite in service profile wpa-wep-for-mac. Type the following command:

23x0# set service-profile wpa-wep-for-mac cipher-wep40 enable success: change accepted.

TKIP is already enabled by default when WPA is enabled.

9Enable PSK authentication in service profile wpa-wep-for-mac. Type the following command:

23x0# set service-profile wpa-wep-for-mac auth-psk enable success: change accepted.

10Configure a passphrase for the preshared key. Type the following command:

23x0# set service-profile wpa-wep-for-mac psk-phrase "passphrase to convert into a preshared key"

success: change accepted.

11Display the WPA configuration changes. Type the following command:

23x0# show service-profile wpa-wep-for-mac

ssid-name:	voice		ssid-type:	crypto
beacon:		yes	auth-fallthru: last-resort
WEP Key 1	value:	<none>	WEP Key 2	value:	<none>
WEP Key 3	value:	<none>	WEP Key 4	value:	<none>
WEP Unicast Index:		1	WEP Multicast Index:		1
Long Preamble:		YES	Shared Key Auth:		NO
WPA enabled:

ciphers: cipher-tkip, cipher-wep40

authentication: pre-shared key

TKIP countermeasures time: 60000ms

pre-shared-key: 92f99cd49e186cadee13fda7b2a2bac78975 a5723a4a6b31b5b5395d6b001dbe

12Map service profile wpa-wep-for-macto radio profile rp3. Type the following commands:

23x0# set radio-profile rp3 service-profile wpa-wep-for-mac success: change accepted.

13Apply radio profile rp3 to radio 1 on port 4 and to radios 1 and 2 on port 6 and enable the radios, and verify the configuration changes. Type the following commands:

23x0# set ap 4,6 radio 1 radio-profile rp3 mode enable success: change accepted.

23x0# set ap 6 radio 2 radio-profile rp3 mode enable

320657-A

Image 218

Contents

Nortel Wlan Security Switch 2300 Series Configuration Guide Restricted rights legend Copyright Nortel Networks Limited 2005. All rights reservedTrademarks Statement of conditions USA requirements only Nortel Inc. software license agreement Limited Product Warranty Legal Information Limited Warranty Software License Agreement Nortel Wlan Security Switch 2300 Series Configuration Guide SSH Source Code Statement OpenSSL Project License Statements Class a Statement RF Radiation Hazard Warning Deployment Statement 320657-A Contents Configuring and Managing Ports and VLANs Configuring and Managing IP Interfaces and Services Configuring Snmp Configuring and Managing Mobility Domain Roaming Configuring AP access points Wi-Fi Multimedia Configuring and Managing Igmp Snooping Managing Keys and Certificates Configuring AAA for Network Users Configuring Communication with Radius Managing 802.1X on the WSS Switch Managing System Files Troubleshooting a WS Switch Supported Radius Attributes Contents 320657-A Getting Help from the Nortel Web site How to get HelpGetting Help over the phone from a Nortel Solutions Center Getting Help through a Nortel distributor or reseller Introducing the Nortel Wlan 2300 System Nortel Wlan 2300 System Planning, Configuration, and Deployment Documentation Safety and Advisory Notices Bold text Menu Name CommandText and Syntax Conventions Using the Command-Line Interface CLI Conventions Command Prompts NT-mm-nnnnnn Clear interface vlan-idip Set port enable disable port-listSyntax Notation Clear fdb dynamic port port-list vlan vlan-id IP Address and Mask Notation Text Entry Conventions and Allowed CharactersMAC Address Notation MAC Address Wildcards User Wildcards, MAC Address Wildcards, and Vlan WildcardsUser Wildcards 0001 000102 00010203 0001020304 Vlan WildcardsMatching Order for Wildcards Port Lists 23x0# set port enable23x0# reset port 23x0# show port poe 1,2,4,13 Virtual LAN Identification Command-Line Editing Keyboard Shortcuts Keyboard Shortcuts Function History Buffer Tabs Single-Asterisk * Wildcard Character Double-Asterisk ** Wildcard Characters 23x0# show i? Using CLI Help23x0# help Commands 23x0# show ip telnet Understanding Command DescriptionsServer Status Port Enabled Set ap dap name Configuring AAA for Administrative and Local Access Overview of AAA for Administrative and Local Access Configuring AAA for Administrative and Local Access Before You Start Typical Nortel Wlan 2300 System About Administrative Access Access Modes First-Time Configuration using the Console Types of Administrative Access 23x0 enable Enabling an AdministratorPassword Username WMS Enable Password Setting the WSS Switch Enable PasswordSetting the WSS Enable Password for the First Time 23x0# set enablepass Configuring AAA for Administrative and Local Access Authenticating at the Console 23x0# set authentication console * local Customizing AAA with Wildcards and Groups Setting User Passwords Set user username password password Configuring Accounting for Administrative UsersAdding and Clearing Local Users for Administrative Access Success User Jose created 23x0# show accounting statistics 23x0# save config configday Displaying the AAA ConfigurationSaving the Configuration 23x0# show aaa Administrative AAA Configuration Scenarios Local Authentication Success change accepted 23x0# set server group sg1 members r1 Local Override and Backup Local Authentication Authentication When Radius Servers Do Not Respond Configuring and Managing Ports and VLANs Configuring and Managing Ports Setting the Port Type Vlan WSS 2380 40 AP Software License Upgrade Show version Setting a Port for a Directly Connected AP access port 23x0# set port type ap 4-6 model 2330 poe enable Configuring for a Distributed AP Setting a Port for a Wired Authentication User Clear port type port-list 23x0# set port type wired-authClearing a Port Clear dap dap-num Clearing a Distributed AP23x0# clear port type Removing a Port Name Configuring a Port NameSetting a Port Name Show port preference port-list Set port preference port-listrj45Clear port preference port-list RJ45 Gigabit Ports-Autonegotiation and Flow Control Configuring Port Operating Parameters10/100 Ports-Autonegotiation and Port Speed Disabling or Reenabling Power over Ethernet Disabling or Reenabling a Port Reset port port-list Resetting a PortSet port poe port-listenable disable Displaying PoE State Displaying Port Configuration and StatusDisplaying Port Information Show port status port-list Monitoring Port Statistics Displaying Port StatisticsClearing Statistics Counters 23x0# monitor port counters Load Sharing Configuring Load-Sharing Port GroupsConfiguring a Port Group Link Redundancy Displaying Port Group Information Configuring and Managing VLANsRemoving a Port Group Interoperating with Cisco Systems EtherChannel Users and VLANs Understanding VLANs in Nortel WSS SoftwareVLANs, IP Subnets, and IP Addressing Traffic Forwarding Vlan NamesRoaming and VLANs 802.1Q Tagging Tunnel Affinity Adding Ports to a Vlan Configuring a VlanCreating a Vlan Set vlan vlan-numname name 23x0# clear vlan red port Removing an Entire Vlan or a Vlan Port23x0# set vlan red port 9-11,21 23x0# clear vlan marigold port 13 tag 23x0# clear vlan ecru Changing Tunneling Affinity Set vlan vlan-idtunnel-affinity num Managing the Layer 2 Forwarding Database Show vlan config vlan-id23x0# show vlan config burgundy Displaying Vlan Information Types of Forwarding Database Entries How Entries Enter the Forwarding Database Displaying Forwarding Database Entries Displaying Forwarding Database InformationDisplaying the Size of the Forwarding Database Show fdb count perm static dynamic vlan vlan-id 23x0# set fdb perm 00bbccddeeff port 3,5 vlan blue 23x0# set fdb static 002b3c4d5e6f port 1 vlan defaultAdding an Entry to the Forwarding Database 23x0# clear fdb port 3,5 Removing Entries from the Forwarding Database23x0# clear fdb dynamic Displaying the Aging Timeout Period Port and Vlan Configuration ScenarioConfiguring the Aging Timeout Period Changing the Aging Timeout Period 23x0# set port 8-13 name manufacturing 23x0# set port 6 name confroom123x0# set port 7 name confroom2 23x0# set system countrycode US 23x0# set port type ap 2-16 model 2330 poe enable MAC 23x0# set port type wired-auth 17,18 Port group backbonelink is up Ports 22 Save the configuration. Type the following command Configuring and Managing IP Interfaces and Services MTU Support Configuring and Managing IP Interfaces Enabling the Dhcp Client Statically Configuring an IP InterfaceAdding an IP Interface 23x0# show interface Set interface vlan-idip dhcp-client enable disable23x0# set interface corpvlan ip dhcp-client enable Interface Corpvlan4 Configuration Status Enabled Dhcp State 23x0# show dhcp-client Disabling or Reenabling an IP Interface Set interface vlan-idstatus up down Removing an IP Interface Show interface vlan-id Configuring the System IP AddressDisplaying IP Interface Information Designating the System IP Address Set system ip-address ip-addr Displaying the System IP Address Show system Clear system ip-address Configuring and Managing IP RoutesClearing the System IP Address Configuring and Managing IP Interfaces and Services 320657-A 23x0# show ip route Displaying IP RoutesShow ip route destination 224.0.0.0/ 4 IP Local 23x0# set ip route 192.168.4.0 255.255.255.0 10.5.4.2 23x0# set ip route default 10.5.4.1Adding a Static Route Removing a Static Route Managing the Management Services23x0# clear ip route default 23x0# clear ip route 192.168.4.69/24 Managing SSH Login TimeoutsSession Timeouts Enabling SSH Show crypto key ssh Changing the SSH Service Port NumberAdding an SSH User 23x0# show crypto key ssh ec6f567fd1fdc02893aea4f97cf51304 23x0# show sessions admin Changing SSH TimeoutsShow sessions admin Clear sessions admin ssh session-id 23x0# clear sessions admin ssh Enabling Telnet Telnet Login TimersManaging Telnet Adding a Telnet User Managing Telnet Server Sessions Changing the Telnet Service Port NumberResetting the Telnet Service Port Number to Its Default Enabling Https Configuring and Managing DNSManaging Https Displaying Https Information Configuring and Managing IP Interfaces and Services Set ip dns enable disable Enabling or Disabling the DNS Client Removing a DNS Server Configuring DNS ServersAdding a DNS Server Set ip dns server ip-addrprimary secondary Removing the Default Domain Name Configuring a Default Domain NameAdding the Default Domain Name Set ip dns domain name Show ip dns Configuring and Managing AliasesDisplaying DNS Server Information 23x0# show ip dns 23x0# set ip alias HR1 Adding an AliasSet ip alias name ip-addr Removing an Alias Clear ip alias name Show ip alias name Configuring and Managing Time ParametersDisplaying Aliases 23x0# show ip alias Clearing the Time Zone Setting the Time ZoneDisplaying the Time Zone Clearing the Summertime Period Configuring the Summertime PeriodDisplaying the Summertime Period 23x0# set timedate date feb 29 2004 time Statically Configuring the System Time and DateSet timedate date mmm dd yyyy time hhmmss Time now is Sun Feb 29 2004, 235802 PST Displaying the Time and Date Show timedate 23x0# show timedate Configuring and Managing NTP 23x0# set ntp server Adding an NTP ServerSet ntp server ip-addr Removing an NTP Server Clear ntp server ip-addrall 23x0# set ntp update-interval Changing the NTP Update IntervalSet ntp update-interval seconds Resetting the Update Interval to the Default Clear ntp update-interval Set ntp enable disable Enabling the NTP Client Show ntp Managing the ARP TableDisplaying NTP Information 23x0# show arp Displaying ARP Table EntriesShow arp ip-addr 23x0# set arp static 10.10.10.1 00bbccddeeff Adding an ARP EntrySet arp permanent static dynamic ip-addrmac-addr Success added arp 10.10.10.1 at 00bbccddeeff on Vlan Set arp agingtime seconds Changing the Aging TimeoutPinging Another Device 23x0# set arp agingtime 23x0# show sessions telnet client Logging In to a Remote Device23x0# telnet 23x0# clear sessions telnet client 23x0# traceroute server1 IP Interfaces and Services Configuration ScenarioTracing a Route 23x0# set ip dns server 10.10.10.69 Primary 23x0# set ip route default 10.20.10.123x0# set system ip-address 23x0# set ip dns server 10.20.10.69 Secondary 23x0# set ip dns enableSummertime is enabled, and set to PDT 23x0 # show ip dns Overview Configuring SnmpConfiguring Snmp Set system location string set system contact string Setting the System Location and Contact Strings23x0# set system contact sysadmin1 23x0# set system location 3rdfloorcloset Enabling Snmp Versions Set snmp protocol v1 v2c usm all enable disable23x023x0# set snmp protocol all enable Configuring Community Strings SNMPv1 and SNMPv2c Only Clear snmp community name comm-string Creating a USM User for SNMPv3 Clear snmp usm usm-username Command Examples 23x0# set snmp usm snmpmgr1 snmp-engine-id local Setting Snmp Security 23x0# set snmp security encrypted Configuring a Notification Profile Clear snmp profile profile-name 23x0# set snmp notify profile default send all Configuring Snmp Clear snmp notify target target-num Configuring a Notification TargetSecurity unsecured authenticated encrypted 23x0# set snmp notify target 2 10.10.40.10 v1 trap 23x0# set ip snmp server enable Enabling the Snmp ServiceSet ip snmp server enable disable Displaying Snmp Information Displaying Snmp Version and Status Information Displaying the Configured Snmp Community Strings Displaying USM Settings 23x0# show snmp notify profile insert updated example Displaying Notification Profiles 23x0# show snmp notify target insert updated example Displaying Notification Targets Displaying Snmp Statistics Counters Configuring Snmp 320657-A Configuring and Managing Mobility Domain Roaming About the Mobility Domain Feature Configuring a Mobility Domain 23x0# set mobility-domain mode seed domain-name Pleasanton Configuring the SeedSet mobility-domain mode seed domain-name mob-domain-name Configuring Member WSSs on the Seed Set mobility-domain member ip-addr 23x0# set mobility-domain mode member seed-ip Configuring a MemberSet mobility-domain mode member seed-ip ip-addr 192.168.14.6 Displaying Mobility Domain Status2370# show mobility-domain status 192.168.15.5 This WSS is a member, with seed Displaying the Mobility Domain Configuration2370# show mobility-domain config Clearing a Mobility Domain from a WSS 2370# clear mobility-domain Clearing a Mobility Domain Member from a Seed Clear mobility-domain member ip-addr Displaying Roaming Stations 23x0# show roaming station Affinity Displaying Roaming VLANs and Their Affinities23x0 # show roaming vlan 23x0 # show tunnel Understanding the Sessions of Roaming UsersDisplaying Tunnel Information State Port Requirements for Roaming to Succeed Active Effects of Timers on Roaming WSS-20show sessions network verbose Mobility Domain ScenarioMonitoring Roaming Sessions 23x0# set mobility-domain member seed-ip 23x0# show tunnel 23x0# show mobility-domain config23x0# show roaming vlan Configuring User Encryption Wireless Encryption Defaults Default Encryption Configuring WPA WPA Cipher Suites WPA Encryption with Tkip Only WPA Encryption with Tkip and WEP Tkip Countermeasures WPA Authentication Methods WPA Information Element Client Support Encryption Support for WPA and Non-WPA Clients Supported Enabling WPA Configuring WPACreating a Service Profile for WPA Specifying the WPA Cipher Suites Changing the Tkip Countermeasures Timer Value Enabling PSK Authentication Set service-profile name psk-phrase passphrase Set service-profile name auth-psk enable disable23x0# set service-profile wpa auth-psk enable Set service-profile name psk-raw hex 23x0# show service-profile wpa Displaying WPA SettingsShow service-profile name ? Set radio-profile name service-profile name Enabling RSN Configuring RSNCreating a Service Profile for RSN Specifying the RSN Cipher Suites Displaying RSN Settings 23x0# set service-profile rsn cipher-ccmp enable Configuring WEP 23x0# set radio-profile blgd2 service-profile rsn Encryption for Dynamic and Static WEP Setting Static WEP Key Values Set service-profile name wep key-index num key value Assigning Static WEP Keys Encryption Configuration Scenarios23x0# set service-profile wepsrvc4 wep active-unicast-index 23x0# set service-profile wpa success change accepted Enabling WPA with Tkip 23x0# show ap config 23x0# set ap 5,11 radio 1 radio-profile rp2 mode enable 23x0# set service-profile wpa-wep success change accepted23x0# show service-profile wpa-wep Enabling Dynamic WEP in a WPA Network Success change accepted Configuring Encryption for MAC Clients 23x0# set service-profile wpa-wep-for-mac 23x0# show service-profile wpa-wep-for-mac 23x0# show ap config Configuring User Encryption 320657-A Configuring AP access points AP Overview Example Nortel Network Country of Operation Directly Connected APs and Distributed APs Distributed AP Network Requirements Distributed APs and STP Distributed APs and Dhcp Option Bias High AP ParametersName Resiliency and Dual-Homing Options for APs Upgrade-firmware EnableDisable Group Dual-Homed Direct Connections to a Single WSS Dual-Homed Direct and Distributed Connections to WSSs Dual-Homed Distributed Connections to WSSs on Both AP Ports AP Boot Process Dual-Homed Distributed Connections to WSSs on One AP Port Configuring AP access points Configuring AP access points Configuring AP access points Example AP Boot over Layer 2 Network Example AP Boot over Layer 3 Network Example Boot of Dual-Homed AP Dual-Homed AP Booting Session Load Balancing Service Profiles Public and Private SSIDs Dap status command Encryption Configuring AP access points Radio Profiles RF Auto-Tuning Default Radio Profile Channel Tx-powerRadio-Specific Parameters Antennatype Internal Nortel external antenna model Configuring AP access points Specifying the Country of Operation Set system countrycode code WSS 23x0# show system Configuring a Template for Automatic AP Configuration How an Unconfigured AP Finds an WSS Switch To Configure It 23x0# show dap config auto Configured APs Have Precedence Over Unconfigured APsConfiguring a Template Radio 2 type 802.11a, mode enabled, channel dynamic Changing AP Parameter Values 23x0# show dap status auto 23x0# set dap auto mode enable23x0# set dap auto radio 1 radio-profile autodap1 Set dap auto persistent dap-numall Configuring AP Port Parameters Setting the Port Type for a Directly Connected AP Port parameter Setting Configuring an Indirectly Connected AP 23x0# set port type ap 11-14,16 model 2330 poe enable Clearing an AP from the Configuration Changing AP Names Enabling LED Blink Mode Configuring a Load-Balancing GroupDisabling or Reenabling Automatic Firmware Upgrades Changing Bias Encryption Options Configuring AP-WSS SecurityEncryption Key Fingerprint RSA aaaaaaaaaaaaaaaa aaaaaaaaaaaaaaaa Confirming an AP’s Fingerprint on an WSS Switch 23x0# show dap status Set dap security require optional Setting the AP Security Requirement on an WSS SwitchSet dap num fingerprint hex 23x0# set dap security require Fingerprint Log Message Disabling or Reenabling Encryption for an Ssid Configuring a Service ProfileChanging the Fallthru Authentication Type Disabling or Reenabling Beaconing of an Ssid Configuring AP access points Creating a New Profile Configuring a Radio ProfileSet radio-profile name mode enable disable Changing Radio Parameters Set radio-profile name dtim-interval interval Set radio-profile name beacon-interval interval23x0# set radio-profile rp1 beacon-interval 23x0# set radio-profile rp1 dtim-interval Set radio-profile name frag-threshold threshold Set radio-profile name rts-threshold threshold23x0# set radio-profile rp1 rts-threshold 23x0# set radio-profile rp1 frag-threshold Set radio-profile name max-tx-lifetime time Set radio-profile name max-rx-lifetime time23x0# set radio-profile rp1 max-rx-lifetime 23x0# set radio-profile rp1 max-tx-lifetime Set radio-profile name preamble-length long short Set radio-profile name 11g-only enable disable23x0# set radio-profile rp1 11g-only enable 23x0# set radio-profile rplong preamble-length long Clear radio-profile name parameter Resetting a Radio Profile Parameter to its Default ValueRemoving a Radio Profile Clear radio-profile name Configuring Radio-Specific Parameters Configuring the Channel and Transmit Power 23x0# set ap 5 radio 2 channel 36 tx-power Configuring the External Antenna Model23x0# set ap 11 radio 1 channel 1 tx-power 23x0# set dap 1 radio 1 antennatype ANT1060 Mapping the Radio Profile to Service Profiles 23x0# set radio-profile rp2 service-profile wpaclients Disabling or Reenabling Radios 23x0# set ap 11-14,16 radio 2 radio-profile rp1 mode enable23x0# set ap 6 radio 1 radio-profile rp1 mode disable Assigning a Radio Profile and Enabling Radios Enabling or Disabling Individual Radios Set ap port-listdap dap-numradio 1 2 mode enable disable23x0# set ap 3,7 radio 2 mode disable 23x0# set radio-profile rp1 mode disable Disabling or Reenabling All Radios Using a Profile23x0# set radio-profile rp1 mode enable 23x0# clear ap 3 radio Resetting a Radio to its Factory Default SettingsClear ap port-listdap dap-numradio 1 2 all Displaying AP Information Restarting an AP Displaying AP Configuration Information 23x0# show dap config 23x0 # show dap global Displaying a List of Distributed APsShow dap global dap-numserial-id serial-ID Show dap unconfigured 23x0 # show dap unconfigured Displaying Connection Information for Distributed APs Show dap connection dap-numserial-id serial-ID Displaying Service Profile Information 23x0 # show service-profile wpaclients Show radio-profile name ? 23x0 # show radio-profile defaultDisplaying Radio Profile Information Displaying AP Status Information Displaying AP Statistics Counters 23x0 # show ap counters Totl 116665 7694 11643396 629107 112115 3368239 142900 Configuring RF Auto-Tuning RF Auto-Tuning Overview Initial Channel and Power Assignment Channel Tuning Channel and Power TuningPower Tuning Tuning the Transmit Data Rate RF Auto-Tuning Parameters Changing RF Auto-Tuning Settings Min-client-rate For 802.11b For 802.11a Changing the Channel Tuning Interval Changing Channel Tuning SettingsDisabling or Reenabling Channel Tuning Changing the Channel Holddown Interval Changing the Power Tuning Interval Changing Power Tuning SettingsEnabling Power Tuning Changing the Power Backoff Interval 23x0# set ap 7 radio 1 auto-tune max-retransmissions 23x0# set ap 7 radio 1 auto-tune max-powerChanging the Client Retransmission Threshold Displaying RF Auto-Tuning Information Changing the Minimum Transmit Data Rate 23x0# show ap config 2 radio Displaying RF Auto-Tuning Settings23x0# show radio-profile default Displaying RF Neighbors 23x0# show auto-tune neighbors ap 2 radio Displaying RF Attributes 23x0# show auto-tune attributes ap 2 radio Configuring RF Auto-Tuning 320657-A Wi-Fi Multimedia How WMM Works in WSS Software QoS on the WSS Switch QoS on an AP WMM in a Nortel Network WMM Priority Mappings Set radio-profile name wmm enable disableDisabling or Reenabling WMM Show dap qos-stats dap-numshow dap qos-stats port-list Displaying WMM Information23x0# show radio-profile radprof1 23x0# show dap qos-stats Wi-Fi Multimedia Configuring and Managing Spanning Tree Protocol Enabling the Spanning Tree Protocol Set spantree enable disable23x0# set spantree enable Snmp Port Path Cost Defaults Changing Standard Spanning Tree Parameters Port Priority 23x0# set spantree priority 69 vlan pink Changing the Bridge PrioritySet spantree priority value all vlan vlan-id Changing the STP Port Cost Resetting the STP Port Cost to the Default ValueChanging STP Port Parameters 23x0# set spantree portpri 3-4 priority Resetting the STP Port Priority to the Default ValueChanging the STP Port Priority 23x0# set spantree portvlanpri 3-4 priority 48 vlan mauve Changing the STP Hello Interval Changing Spanning Tree TimersChanging the STP Forwarding Delay Changing the STP Maximum Age Configuring and Managing STP Fast Convergence Features 23x0# set spantree maxage 15 all Uplink Fast Convergence 23x0# set spantree portfast port 9,11,13 enable Configuring Port Fast ConvergenceSet spantree portfast port port-listenable disable Show spantree portfast port-list Port Vlan Portfast Disable EnableDisplaying Port Fast Convergence Information 23x0# show spantree portfast 23x0# set spantree backbonefast enable Configuring Backbone Fast ConvergenceSet spantree backbonefast enable disable Show spantree backbonefast Backbonefast is enabledDisplaying the Backbone Fast Convergence State 23x0# show spantree backbonefast Configuring Uplink Fast Convergence Set spantree uplinkfast enable disable Show spantree uplinkfast vlan vlan-id Displaying Spanning Tree InformationDisplaying Uplink Fast Convergence Information 23x0# show spantree uplinkfast 23x0# show spantree vlan mauve Displaying STP Bridge and Port InformationShow spantree port-listvlan vlan-id active 23x0# show spantree portvlancost Displaying the STP Port Cost on a Vlan BasisShow spantree portvlancost port-list Port 1 Vlan 1 have path cost Show spantree blockedports vlan vlan-id 23x0# show spantree blockedports vlan defaultDisplaying Blocked STP Ports 23x0# show spantree statistics 1 Bpdu related parameters Displaying Spanning Tree StatisticsShow spantree statistics port-listvlan vlan-id Hold timer value Delay root port Timer Topology change TimerTopology change Timer value Hold timer Delay root port Timer value Timer restarted is Clearing STP Statistics Spanning Tree Configuration Scenario23x0# set port disable Clear spantree statistics port-listvlan vlan-id Disabled 128 Default None Backbone DownSpanning tree mode 23x0# set port enable Down Auto Network 10/100BaseTx 1000/full Disabling or Reenabling Proxy Reporting Set igmp enable disable vlan vlan-idDisabling or Reenabling Igmp Snooping Set igmp querier enable disable vlan vlan-id Changing Igmp TimersSet igmp proxy-report enable disable vlan vlan-id Enabling the Pseudo-Querier Changing the Query Interval Set igmp qi seconds vlan vlan-id Changing the Other-Querier-Present Interval Set igmp oqi seconds vlan vlan-id Changing the Query Response Interval Set igmp qri tenth-seconds vlan vlan-id Changing the Last Member Query Interval Set igmp lmqi tenth-seconds vlan vlan-id Changing Robustness Set igmp mrsol enable disable vlan vlan-idEnabling Router Solicitation Set igmp rv num vlan vlan-id Set igmp mrsol mrsi seconds vlan vlan-id Configuring Static Multicast PortsChanging the Router Solicitation Interval Set igmp mrouter port port-listenable disable Adding or Removing a Static Multicast Router Port Adding or Removing a Static Multicast Receiver Port Set igmp receiver port port-listenable disableDisplaying Multicast Information 192.28.7.5 Dvmrp Group Port Receiver-IP Receiver-MAC Show igmp vlan vlan-id23x0# show igmp vlan orange Show igmp statistics vlan vlan-id Displaying Multicast Statistics OnlyClearing Multicast Statistics Clear igmp statistics vlan vlan-id Show igmp querier vlan orange Displaying Multicast QueriersShow igmp querier vlan vlan-id Querier for vlan orange Port Querier-IP Querier-MAC Show igmp mrouter vlan orange Displaying Multicast RoutersShow igmp mrouter vlan vlan-id 192.28.7.5 000102030405 Dvmrp Vlan red Session Port Receiver-IP Receiver-MAC Displaying Multicast Receivers23x0# show igmp receiver-table group 237.255.255.0/24 Configuring and Managing Igmp Snooping 320657-A Configuring and Managing Security ACLs About Security Access Control Lists Overview of Security ACL Commands Setting Security ACLs Creating and Committing a Security ACL Security ACL Filters 23x0# set security acl ip acl-1 permit 192.168.1.4 Setting a Source IP ACLCommon IP Protocol Numbers Wildcard Masks Class of ServiceClass-of-Service CoS Packet Handling Configuring and Managing Security ACLs Setting an Icmp ACL Common Icmp Message Types and Codes Common Icmp Message Types and Codes Setting a UDP ACL Setting TCP and UDP ACLsSetting a TCP ACL Configuring and Managing Security ACLs Determining the ACE Order 23x0# commit security acl all Committing a Security ACL23x0# commit security acl acl-99 Viewing Committed Security ACLs Viewing Security ACL InformationViewing the Edit Buffer Viewing Security ACL Details Displaying Security ACL Hits 23x0# show security acl hits ACL hit-counters 23x0# clear security acl acl-99 Mapping Security ACLsClearing Security ACLs 23x0# set user Natasha attr filter-id acl-222.in Mapping User-Based Security ACLs23x0# commit security acl acl-222 success change accepted Configuring and Managing Security ACLs 23x0# set security acl map acl-222 port 2 tag 1-3,5 Displaying ACL Maps to Ports, VLANs, and Virtual PortsClearing a Security ACL Map 23x0# show security acl map acl-999 ACL acljoe is mapped to Modifying a Security ACL23x0# show security acl map acljoe 23x0# clear security acl map acljoe port 4 Adding Another ACE to a Security ACL 23x0# show security acl info all Placing One ACE before Another Modifying an Existing Security ACL ACL edit-buffer table Clearing Security ACLs from the Edit Buffer23x0# show security acl editbuffer Type Status Acl-a Not Committed Acl-111 ACL edit-buffer information for all Using ACLs to Change CoS23x0# rollback security acl acl-111 Filtering Based on Dscp Values 23x0# commit security acl voip Enabling Prioritization for Legacy Voice over IP23x0# set security acl ip voip permit 0.0.0.0 23x0# set security acl map voip vlan corpvlan out Security ACL Configuration Scenario Enabling SVP Optimization for SpectraLink Phones 23x0# save config Why Use Keys and Certificates? Managing Keys Certificates Wireless Security through TLS About Keys and Certificates PEAP-MS-CHAP-V2 Security Public Key Infrastructures Public and Private Keys Digital Certificates Pkcs #7, Pkcs #10, and Pkcs #12 Object Files Crypto generate key commandCreating Keys and Certificates Pkcs Object Files Supported by Nortel Managing Keys and Certificates Procedures for Creating and Validating Certificates Admin key pair generated Crypto generate key admin eap ssh webaaa 512 102423x0# crypto generate key admin Creating Public-Private Key Pairs Generating Self-Signed Certificates Crypto generate self-signed admin eap webaaa23x0# crypto generate self-signed admin Country Name US Crypto otp admin eap webaaa one-time-password Crypto pkcs12 admin eap webaaa filename 23x0# crypto generate request admin Installing a CA’s Own Certificate Begin Certificate Displaying Certificate and Key Information Key and Certificate Configuration Scenarios23x0# show crypto certificate admin Certificate Creating Self-Signed Certificates 23x0# crypto generate self-signed adminSelf-signed cert for admin is ENDCERTIFICATE-----23x0#crypto generate self-signed eap 23x0# show crypto certificate eap 23x0# show crypto certificate admin20# crypto generate self-signed webaaa Country Name US 23x0# show crypto certificate webaaa Certificate 23x0# copy tftp//192.168.253.1/2048admn.p12 2048admn.p12 23x0# crypto otp admin SeC%#6@o%c23x0# crypto pkcs12 admin 2048admn.p12 23x0# copy tftp//192.168.253.1/20481x.p12 20481x.p12 Keypair Device certificate CA certificate Email Address admin@example.com Unstructured Name wiring closet 12 CSR for admin is 23x0# show crypto ca-certificate admin 23x0# crypto certificate admin23x0# crypto ca-certificate admin Enter PEM-encoded certificate Configuring AAA for Network Users About AAA for Network Users Authentication Authentication Types Authentication Algorithm Authentication Flowchart for Network Users To 802.1X? Yes User Credential Requirements Ssid Name AnyLast-Resort Processing Configuring AAA for Network Users Authorization CLI Accounting Summary of AAA Features AAA Tools for Network Users Wildcards and Groups for Network User Classification Wildcard Any for Ssid Matching Local Override Exception AAA Methods for Ieee 802.1X and Web Network AccessAAA Rollover Process Remote Authentication with Local Backup Remote Pass-Through or Local Authentication Ieee 802.1X Extensible Authentication Protocol Types EAP-MD5 Ways an WSS Switch Can Use EAP Configuring 802.1X Authentication Effects of Authentication Type on Encryption Method Configuring 802.1X Acceleration Using Pass-Through Authenticating through a Local Database Binding User Authentication to Machine Authentication Authentication Rule Requirements Set dot1x bonded-period seconds Bonded Authentication PeriodBonded Authentication Configuration Example Clear dot1x bonded-period 23x0# set dot1x bonded-period Displaying Bonded Authentication Configuration InformationShow dot1x config 23x0# show dot1x config Configuring Authentication and Authorization by MAC Address Clearing MAC Users and Groups Adding and Clearing MAC Users and User Groups LocallyAdding MAC Users and Groups 23x0# set authentication mac ssid voice 010102* local Configuring MAC Authentication and Authorization23x0# set authentication mac ssid voice 010102030405 local 23x0# set mac-user 000102030405 attr vlan-name red Set radius server server-nameauthor-password password Configuring Web-based AAAChanging the MAC Authorization Password for Radius 23x0# set radius server bigbird author-password h00per How Portal Web-based AAA Works Web-based AAA Requirements and Recommendations WSS Requirements Configuring AAA for Network Users Client Web Browser Requirements WSS RecommendationsClient NIC Requirements Client Web Browser Recommendations 23x0# set user web-portal-mycorp attr vlan-name corpvlan Configuring Portal Web-based AAAPortal Web-based AAA Configuration Example 23x0# show config 23x0# show sessions network ssid mycorp 23x0# show sessions network ssid mycorp Using a Custom Login TitleMy Corp webAAA/title Copying and Modifying the Nortel LoginCustom Login Page Scenario 23x0# mkdir mycorp-webaaa success change accepted H3Welcome to Mycorp’s Wireless LAN/h3BWARNING/b My corp’s warning text 23x0# dir mycorp-webaaa Using Dynamic Fields in Web-based AAA Redirect URLs Variables for Redirect URLs Description Configuring Last-Resort Access Configuring AAA for Users of Third-Party APs WSS Switch Serving as Radius Proxy Authentication Process for 802.1X Users of a Third-Party AP Third-Party AP Requirements WSS Switch RequirementsRequirements 23x0# set authentication mac wired aabbcc010101 srvrgrp1 Set authentication mac wired mac-addr-wildcard method123x0# set port type wired-auth 3-4 tag Set radius proxy port port-listtag tag-valuessid ssid-name 23x0# set authentication proxy ssid mycorp ** srvrgrp1 23x0# set radius proxy client address 10.20.20.9 key radkey1 Assigning Authorization Attributes End-date Session-timeout Idle-timeoutService-type Filter-id Time-of-day SsidStart-date Url Vlan-name Assigning Attributes to Users and Groups 23x0# set user Jose attr filter-id acl-101.in Assigning a Security ACL to a User or a GroupAssigning a Security ACL Locally 23x0# set usergroup eastcoasters attr filter-id acl-101.in Assigning a Security ACL on a Radius Server Clearing a Security ACL from a User or Group Clear mac-usergroup groupname attr filter-id 23x0# set mac-usergroup mac-fans attr encryption-type Assigning Encryption Types to Wireless UsersAssigning and Clearing Encryption Types Locally Assigning and Clearing Encryption Types on a Radius Server About the Location Policy How the Location Policy Differs from a Security ACL 23x0# set location policy deny if user eq *.theirfirm.com Setting the Location PolicyApplying Security ACLs in a Location Policy Rule Displaying and Positioning Location Policy Rules WSS-20show location policy Clear location policy rule-number Configuring Accounting for Wireless Network UsersSet accounting admin console dot1x mac web Configuring AAA for Network Users Viewing Local Accounting Records WSS-20-0017#show accounting statistics Viewing Roaming Accounting RecordsWSS-20-0013#show accounting statistics May 21 Acct-Status-Type=STOP Acct-Authentic=2 Rs-3 Set authentication admin Jose sg3Server Addr Ports Rs-4 Set authentication web ssid corpa ** corpasrvr Avoiding AAA Problems in Configuration OrderSet authentication web ssid any ** sg1 Vlan-Name = k2 Configuring AAA for Network Users Configuration for a Correct Processing Order Using Authentication and Accounting Rules TogetherConfiguration Producing an Incorrect Processing Order 23x0# set accounting dot1x ssid mycorp * start-stop group1 Configuring a Mobility Profile 23x0# set mobility-profile name roses-profile port 2-4,7,9 23x0# show mobility-profile Mobility Profiles Network User Configuration Scenarios23x0# set mobility-profile mode enable NamePorts ========================= Roses-profile 23x0# show security acl info acl-101 General Use of Network User Commands23x0# set user EXAMPLE\username attr filter-id acl-101.in Mobility Profiles NamePorts ========================= Tulip WSS-20save config Enabling Radius Pass-Through Authentication 23x0# set radius server r1 address 10.1.1.1 key sunny 23x0# set user Natasha attr session-timeout Enabling PEAP-MS-CHAP-V2 Authentication23x0# set user Natasha password moon Unstructured Name wiring closet Enabling PEAP-MS-CHAP-V2 Offload 23x0# set radius server r1 address 10.1.1.1 key starry 23x0# set radius server r1 address 10.1.1.1 key starry Overriding AAA-Assigned VLANs Configuring Communication with Radius Radius Overview Configuring Communication with Radius Configuring Radius Servers Before You Begin 23x0# set radius deadtime Configuring Global Radius DefaultsClear radius deadtime key retransmit timeout 23x0# set radius key r8gney 23x0# clear radius client system-ip Setting the System IP Address as the Source Address23x0# set radius client system-ip Configuring Individual Radius Servers Set radius server server-nameaddress ip-address key string Clear radius server server-name Configuring Radius Server GroupsDeleting Radius Servers Ordering Server Groups Configuring Load BalancingCreating Server Groups Clear server group group-nameload-balance Set server group group-nameload-balance enableAdding Members to a Server Group 23x0 # show aaa Configuring Communication with Radius Radius and Server Group Configuration Scenario Deleting a Server Group 23x0# set server group shorebirds load-balance enable Managing 802.1X on WSS Switch Managing 802.1X on Wired Authentication Ports Success dot1x authcontrol enabled Set dot1x authcontrol enable disable23x0# set dot1x authcontrol enable Enabling and Disabling 802.1X Globally Setting 802.1X Port Control Managing 802.1X Encryption Keys Success dot1x key transmission enabled Set dot1x key-tx enable disable23x0# set dot1x key-tx enable Enabling 802.1X Key Transmission 23x0# set dot1x tx-period Configuring 802.1X Key Transmission Time IntervalsSet dot1x tx-period seconds Success dot1x tx-period set to Managing WEP Keys Configuring 802.1X WEP RekeyingConfiguring the Interval for WEP Rekeying 23x0# set dot1x max-req Setting EAP Retransmission AttemptsManaging 802.1X Client Reauthentication Success dot1x max request set to 23x0# set dot1x reauth enable Enabling and Disabling 802.1X ReauthenticationSet dot1x reauth enable disable Success dot1x reauthentication enabled Success dot1x max reauth set to Set dot1x reauth-max number-of-attempts23x0# set dot1x reauth-max 23x0# clear dot1x reauth-max Set dot1x reauth-period seconds Setting the 802.1X Reauthentication PeriodSuccess dot1x auth-server timeout set to 23x0# set dot1x reauth-period Clear dot1x max-req Managing Other TimersSetting the Bonded Authentication Period 23x0# set dot1x quiet-period Setting the 802.1X Quiet PeriodSet dot1x quiet-period seconds Success dot1x quiet period set to 23x0# set dot1x timeout auth-server Setting the 802.1X Timeout for an Authorization ServerSet dot1x timeout auth-server seconds 23x0# clear dot1x timeout auth-server Setting the 802.1X Timeout for a Client Displaying 802.1X Information Viewing 802.1X Clients 23x0# show dot1x clients Viewing the 802.1X Configuration Viewing 802.1X Statistics 23x0# show dot1x stats Managing 802.1X on the WSS Switch 320657-A Clear sessions admin console telnet client session-id Displaying and Clearing Administrative SessionsShow sessions admin console telnet client Managing Sessions 23x0# clear sessions admin Displaying and Clearing All Administrative SessionsWSS-20 show sessions admin Tty Username Time Type Tty0 5310 Console Console session Displaying and Clearing an Administrative Console SessionWSS-20 show sessions console 23x0# clear sessions console WSS-20 show sessions telnet Displaying and Clearing Administrative Telnet SessionsTty Username Time Type Tty3 Sshadmin 2099 Telnet session 23x0 # show sessions network Displaying and Clearing Network SessionsDisplaying and Clearing Client Telnet Sessions User Sess IP or MAC 003065168d69 4385 Vlan-wep Displaying Verbose Network Session InformationJose@example.com 5125 Vlan-eng 761 000bbe154656 none 23x0# show sessions network user E Displaying and Clearing Network Sessions by UsernameShow sessions network user user-wildcard Clear sessions network user user-wildcard Show sessions net mac-addr 01055d7e981a Displaying and Clearing Network Sessions by MAC AddressShow sessions network mac-addr mac-addr-wildcard Clear sessions network mac-addr mac-addr-wildcard Show sessions network vlan west Displaying and Clearing Network Sessions by Vlan NameShow sessions network vlan vlan-wildcard Clear sessions network vlan vlan-wildcard 2370# clear sessions network session-id Displaying and Clearing Network Sessions by Session IDClear sessions network session-id session-id Managing System Files About System Files 23x0# show version Displaying Software Version InformationShow version details 23x0# show version details W2 N/A Working with Files Displaying Boot Information23x0# show boot Displaying a List of Files 23x0# dir old 23x0# copy floor2WSS tftp//10.1.1.1/floor2WSS 23x0# copy floor2WSS tftp//10.1.1.1/floor2WSS-backupCopying a File Success sent 365 bytes in 0.401 seconds 910 bytes/sec Successreceived9163214bytesin105.939seconds Bytes/sec 23x0# copy tftp//10.1.1.1/newconfig newconfig23x0# copy tftp//10.1.1.1/newconfig WSSconfig Deleting a File 23x0# copy testconfig tftp//10.1.1.1/testconfig23x0# delete testconfig Delete url Creating a Subdirectory 23x0# mkdir corp2 23x0# rmdir corp2 Managing Configuration FilesRemoving a Subdirectory 23x0# show config area vlan Displaying the Running ConfigurationShow config area area all Managing System Files 23x0# save config newconfig Saving Configuration ChangesSave config filename Success configuration saved to newconfig Success boot config set Set boot configuration-file filename23x0# set boot configuration-file floor2WSS 23x0# load config newconfig Loading a Configuration FileLoad config url Resetting to the Factory Default Configuration Backing Up and Restoring the System Managing System Files Managing Configuration Changes 23x0# restore system tftp/10.10.20.9/sysabak Backup and Restore Examples23x0# backup system tftp/10.10.20.9/sysabak critical Upgrading the System Image Managing System Files 320657-A Rogue Detection Countermeasures About Rogues and RF Detection Rogue Detection Lists Rogue access points and ClientsRogue Classification Rogue Detection and Countermeasures Rogue Detection Algorithm RF Detection Scans Dynamic Frequency Selection DFS Summary of Rogue Detection Features Countermeasures Configuring Rogue Detection Lists Show rfdetect vendor-list Configuring a Permitted Vendor ListSet rfdetect vendor-list client ap mac-addr 23x0# show rfdetect vendor-list Total number of entries Show rfdetect ssid-list Configuring a Permitted Ssid ListSet rfdetect ssid-list ssid-name 23x0# show rfdetect ssid-list Total number of entries Show rfdetect black-list Configuring a Client Black ListSet rfdetect black-list mac-addr 23x0# show rfdetect black-list Show rfdetect attack-list Configuring an Attack ListSet rfdetect attack-list mac-addr 23x0# show rfdetect attack-list Configuring an Ignore List Enabling Countermeasures Disabling or Reenabling Active Scan Enabling AP Signatures Enabling Rogue and Countermeasures Notifications Set rfdetect log enable disableDisabling or Reenabling Logging of Rogues IDS and DoS Alerts Flood Attacks DoS Attacks Netstumbler and Wellenreiter Applications Wireless Bridge Ad-Hoc Network Weak WEP Key Used by Client Disallowed Devices or SSIDs Displaying Statistics Counters IDS Log Message Examples IDS and DoS Log Messages Message Type Displaying RF Detection Information Show rfdetect attack-list Show rfdetect ignore 23x0# show rfdetect clients mac 000c4163fd6d Displaying Rogue ClientsShow rfdetect clients mac mac-addr 23x0# show rfdetect clients 23x0# show rfdetect counters Displaying Rogue Detection CountersShow rfdetect counters 23x0# show rfdetect mobility-domain Displaying Ssid or Bssid Information for a Mobility DomainShow rfdetect mobility-domain ssid ssid-namebssid mac-addr 23x0# show rfdetect mobility-domain ssid nrtl-webaaa 23x0# show rfdetect mobility-domain bssid 000b0e0004d1 23x0 # show rfdetect data Displaying RF Detect DataShow rfdetect data Displaying the APs Detected by an AP Radio 23x0# show rfdetect visible ap 3 radio 23x0# show rfdetect countermeasures Displaying Countermeasures InformationShow rfdetect countermeasures Rogue Detection and Countermeasures 320657-A Appendix a Troubleshooting a WS Switch Fixing Common WSS Setup Problems WSS Setup Problems and Remedies Symptom Diagnosis WSS-2350 Recovering the System PasswordBoot boot OPT+=default WSS-2370, WSS-2380, or WSS-2360 Configuring and Managing the System Log Log Message Components Logging Destinations and Levels Info Debug Using Log Commands Logging to the Log Buffer Logging to the Console Logging Messages to a Syslog Server Setting Telnet Session Defaults Changing the Current Telnet Session Defaults Saving Trace Messages in a File Displaying the Log ConfigurationLogging to the Trace Buffer Running Traces Using the Trace CommandTracing Authentication Activity Tracing Session Manager Activity Stopping a Trace Tracing Authorization ActivityDisplaying a Trace Tracing 802.1X Sessions Displaying Trace Results 23x0# show log trace severity errorAbout Trace Results List of Trace Areas Copying Trace Results to a ServerClearing the Trace Log Viewing AAA Session Statistics Using Show CommandsViewing Vlan Interfaces WSS-2370# show interface Vlan-name = vlan-wep Viewing FDB InformationViewing ARP Information 23x0# show fdb How Remote Traffic Monitoring Works Using Snoop Filters on Radios That Use Active ScanRemotely Monitoring Traffic Best Practices for Remote Traffic Monitoring Appendix a Troubleshooting a WS Switch Configuring a Snoop Filter 23x0# set snoop snoop1 observer 10.10.30.2 snap-length Editing a Snoop Filter Displaying Configured Snoop FiltersMapping a Snoop Filter to a Radio Deleting a Snoop Filter Displaying the Snoop Filter Mappings for All Radios Enabling or Disabling a Snoop FilterDisplaying the Snoop Filters Mapped to a Radio Removing Snoop Filter Mappings 23x0# set snoop snoop1 mode enable stop-after Success filter snoop1 enabled Show snoop stats filter-namedap-numradio 1 Displaying Remote Traffic Monitoring StatisticsPreparing an Observer and Capturing Traffic Capturing System Information for Technical Support Displaying Technical Support Information Success results saved to fortechsupport.gz Sending Information to Nets23x0# show tech-support file fortechsupport 23x0# copy fortechsupport.gz tftp//tftpserver/filename.gz Appendix a Troubleshooting a WS Switch 320657-A Appendix B Supported Radius Attributes Supported Standard and Extended Attributes 801.1X Attributes 801.1X Attributes Radius Nortel Vendor-Specific Attributes Nortel VSAs Appendix C Mobility Domain Traffic Ports Protocol Port Function Appendix C Mobility Domain Traffic Ports 320657-A Appendix D Dhcp Server Configuring the Dhcp Server How the WSS Software Dhcp Server Works 23x0# show dhcp-server Displaying Dhcp Server InformationShow dhcp-server interface vlan-id verbose Appendix D Dhcp Server Glossary Advanced Encryption Standard See AES Authentication, authorization, and accounting See AAA CBC-MAC See Ccmp Cyclic redundancy check See CRC Glossary EAP with Transport Layer Security See EAP-TLS Group master key See GMK Group transient key See GTK Industry Canada See IC Information element See WPA IE Media access control address See MAC address Microsoft Challenge Handshake Authentication Per-VLAN Spanning Tree protocol See PVST+ Port address translation See PAT Power over Ethernet See PoE Quality of service See QoS Remote Authentication Dial-In User Service See Radius Spanning Tree Protocol See STP Temporal Key Integrity Protocol See Tkip Type, length, and value See TLV Wisp WPA information element See WPA IE Glossary 320657-A Index Numerics Index Index DNS Enable password Description Subnet masks for, notation conventions System IP address 366 To ports, VLANs, or virtual ports 368 Index Radius Https Index Configuring 341 rogue access points detecting TCP Snmp STP Uplink fast convergence Index WMS Index 320657-A Command Index Command Index Set dap auto radiotype Command Index Command Index 324 Show spantree blockedports 329