Short haul -10 dB Long haul -32 dB | RAD Data comm IPmux-11 specification

Chapter 4 Configuration	Installation and Operation Manual

Rx sensitivity (Maximum attenuation of the receive signal that can be compensated for by the interface receive path):

Short haul (-10 dB) Long haul (-32 dB)

Trail Mode (Enables the end-to-end transfer of TDM OAM (Operation, administration, and maintenance) data in framed mode, when the payload format is set to V2.

Termination (Trail-extended mode is disabled; the TDM networks function as separate OAM domains)

Extension (Trail-extended mode is enabled; OAM data is passed between the TDM networks)

Line type (E1 framing mode):

Unframed G.703 (Framing is not used)

Framed G.704 (G.704 framing, CRC-4 function disabled) Framed G.704 CRC4 (G.704 framing, CRC-4 function enabled) Framed MF (CAS enabled, CRC-4 function disabled)

Framed MF CRC4 (CAS enabled, CRC-4 function enabled).

Idle Code (code transmitted to fill unused timeslots in the E1 frames): 00 to ff.

4.If you configure the Line type to Framed MF or Framed MF CRC4, type N to display the next page of E1 parameters (Figure 4-15):

Send Upon Fail (Notification sent to the E1 side if Ethernet link fails):

OOS Code (Out-of-service code) AIS (Alarm indication signal)

OOS code (Code to be sent to the E1 side if Ethernet link fails): 0–ff

OOS signaling (Out-of-service signaling method. OOS signal is sent toward the IP path when loss of signal, loss of frame, or AIS is detected at the E1 line. The OOS signal is also sent toward the E1 line when packet receive buffer overrun or underrun occurs.):

Space (Code specified by the Space Signaling Code parameter is sent) Mark (Code specified by the Mark Signaling Code parameter is sent)

Space Mark (Space code is sent in the first 2.5 seconds, then mark code is sent)

Mark Space (Mark code is sent in the first 2.5 seconds, then space code is sent)

Mark signaling code: 0–f

Space signaling code: 0–f

5. Type S to save the changes.

4-14

Configuring IPmux-11 for Operation

IPmux-11 Ver. 2.00

Image 72

RAD Data comm IPmux-11 operation manual Short haul -10 dB Long haul -32 dB

Contents

IPmux-11 Page IPmux-11 Limited Warranty Please observe the following precautions Product Disposal General Safety Practices Connection of AC MainsConnection of DC Mains Ports Safety Status Connection of Data and Telecommunications Cables Electromagnetic Compatibility EMC FCC-15 User Information Canadian Emission Requirements Safety Manufacturers Name Manufacturers AddressProduct Name Supplementary Information Installing IPmux-11 Configuring IPmux-11Connecting the Interfaces Connecting the Power Configuring the IP Management Parameters Configuring E1 and T1 at the Physical LevelConfiguring Bundle Connections Configuring the Internal Bridge Contents Configuration Configuring IPmux-11 for a Typical ApplicationTroubleshooting and Diagnostics Overview Versions Application Features E1 InterfaceT1 Interface Ethernet Interface TDMoIP Operation Modes Fiber Optic Interface OptionsTo calculate optical budget To calculate distance QoS ManagementTiming Physical Description Functional DescriptionOperation Modes Testing Timeslot Assignment in a BundleTiming Modes Network Timing Schemes External Network Timing Frame Format Single Source Clock NetworkTDMoIP TDM Payload Layer Layer IP LayerData Layer Field Length Bytes Vlan Support UDP SupportTDMoMPLS UDP Ports Definition Packet Delay Variation Data Pdvt Buffer Effect on Delay Packetization DelayPdvt Jitter Buffer Ethernet Throughput Framed CAS Round Trip Delay Reorder and Duplication of Ethernet FramesReordering Frames End-to-End Alarm Generation Trail-Extended ModeOAM Connectivity Duplicated Frames Vlan Traffic Behavior Ethernet PortsVlan Check for Packets that are Received by IPmux-11 Vlan Check for Packets Sent by IPmux-11 Switch Operation Modes 11. IPmux-11 with Two Ethernet User Port Automatic Per-Port Rate Limiting Rate Limiting and Vlan Tagging Modes Switch Behavior When Handling User and Network Traffic Switch Behavior User and Network Traffic10. Mode a 11. Mode B 12. Mode C 13. Mode D 14. Mode E 15. Mode F 16. Mode G When operating in the Mode G, the following rules applyBoth user ports can get the same default Vlan ID No VLANs can be created on the network port Switch Behavior When Handling Management Traffic 17. Switch Behavior Management Traffic Technical Specifications AC/DC Source VAC or -40/-60 VDC Power 8W max Consumption NumberConnections Jitter Buffer Size Msec with 1 msec granularity Height Introduction Technical Specifications IPmux-11 Ver Introduction Site Requirements and Prerequisites Package Contents Connecting the Ethernet Equipment Connecting to the E1/T1 Devices Connecting the Ethernet User EquipmentTo connect to the Ethernet user equipment To connect to the E1/T1 devices with balanced interfaces Connecting to the External Clock Source Connecting to the Ascii TerminalConnecting IPmux-11 to Power To connect to the external clock source Connecting AC Power Connecting DC PowerTo connect AC power To connect DC powerPage Controls and Indicators Turning IPmux-11 OnTo turn on IPmux-11 IPmux-11 LEDs and Controls Name Type Function Location Default Settings Default SettingsParameter Default Value System Parameter Default Value Physical Layer TDM, E1Physical Layer TDM, T1 Physical Layer ETH ConnectionBridge Configuration Alternatives LoginWorking with Terminal To start a terminal control session How to use the terminal to perform a desired activity To enter as a user Working with ConfiguRAD Ending a Terminal Configuration SessionWeb Browser Requirements Enter General Web Browsers Operating Procedures To manage IPmux-11 via Web browser Main Menu Configuration System Overview of Menu Operations Configuration Connection and Bridge To power off the unit Turning IPmux-11 Off Configuration Sequence To perform preliminary IPmux configuration Configuring IPmux-11 for Management Configuring IP Host ParametersConfiguring Dhcp Client To access System menu To enable Dhcp client Managing IP Parameters of the IPmux-11 HostLease extension To define the IP parameters manually Configuring Management Parameters Assigning a Name to IPmux-11 and Its LocationDefining Read, Write and Trap Communities To acquire a new IP address from the Dhcp server Authentication/Community Menu Defining Network ManagersTo define read, write and trap communities To define network managers Ethernet port Is masked Configuration Example Local Management via User Ethernet Port Configuring Management Access Permissions and Methods To access The Management Access menuTo add a new user To define the management access method To delete an existing user Configuring Control Port Parameters Management Access ImplementationAccess Method Mode Who is Allowed to Access IPmux-11 Configuring IPmux-11 for Operation Configuring the System ClockTo configure the system clock To select the baud rate 12. System Clock Menu Configuring IPmux-11 at the Physical Level Configuring the E1 TDM InterfaceTo configure the E1 interface Short haul -10 dB Long haul -32 dB Configuring the E1 External Clock Interface Configuring the T1 TDM InterfaceTo configure the external clock E1 interface type TDM E1 Menu To configure T1 interface B8ZS AMI TR-6211 10 seconds Fast 1 second Configuring Ethernet Interfaces To configure Ethernet interfaceTDM T1 Menu 18. ETH Menu To configure bundle connection Select DS0 bundlePSN Type is only available after Bundle ID has been set Configuration VLANs see Configuring the Ethernet Bridge below 20. DS0 Bundle Menu Configuring the Ethernet Bridge To configure Ethernet bridge Rate Limiting Default Vlan Priority Options for this port in the following manner 23. Bridge Menu Setting the Date and Time Additional TasksDisplaying the IPmux-11 Inventory To display the IPmux-11 inventory Displaying the Diagnostics Loopback Information To access the Status menuTo display the diagnostics loopback information Displaying the IPmux-11 Status Displaying the TDM Physical Layer Information Displaying the Ethernet Physical Layer InformationTo display the TDM physical layer information To display the Ethernet physical layer information Displaying the Bundle Connection Information To display the bundle connection information Transferring Software and Configuration Files To transfer a file using TftpDisplaying the System Clock Information To display the system clock status Resetting IPmux-11 From the File Utilities, select Download/Upload using Tftp Resetting IPmux-11 to the Defaults Resetting IPmux-11To reset IPmux-11 to the default settings To reset IPmux-11 Configuration Additional Tasks IPmux-11 Ver Guidelines for Configuring IPmux-11 Units Application Configuring IPmux-11 Units Configuring the IP ParametersConfiguration Summary To configure the host IP parameters Configuring E1 Parameters at the Physical Layer To configure the manager listTo configure E1 parameters at the physical layer Configuring Bundles To connect the bundles Connecting the Bundle for IPmux-11 a Page Monitoring Performance Displaying E1/T1 Statistics To view the E1/T1 statistics E1/T1 Statistics Alarm Description AIS Displaying LAN Statistics To view the LAN statistics LAN Statistics LAN Statistics Parameters Displaying Bundle Connection Statistics Connection Statistics Screen Bundle Connection Parameters Parameter Description Recommendations Try increasing the jitter buffer size Detecting Errors Power-Up Self-TestTo display the self-test results Using Front Panel LEDs To access the event logWorking with the Event Log Displaying Events Monitoring Menu Event List Event Description Corrective Action Clearing Events To clear the event logLogfile will be cleared. Continue ??? Y/N Handling Alarms Masking AlarmsConfiguring the Bundle Statistics Collection To configure the bundle statistic collection Troubleshooting IPmux-11 Troubleshooting ChartFault Probable Cause Remedial Action Testing IPmux-11 Running LoopbacksRunning External Loopback Running Internal Loopback To disable a loopback To display the diagnostic loopback statusTo run a loopback Activating T1 Inband Loopbacks To activate an inband loopback Pinging IP Hosts To ping an IP host Running a Trace Route To run a trace route to an IP host Frequently Asked Questions TDM side alarmsEthernet Side Alarms UDP destination port Layer ToS UDP Destination Port Technical Support Page E1 and T1 Connector Balanced ConnectorTable A-1. E1/T1 Port Connector Pinout Balanced-to-Unbalanced Adapter Cable Ethernet Connectors Control ConnectorTable A-2. Ethernet Connector Pinout Table A-3. Control Connector Pinout External Clock Connector Table A-4. EXT CLK Connector PinoutPage Booting IPmux-11 Accessing the Boot ManagerTo access the Boot Manager menu Downloading the Application and Configuration Software Downloading Application Files via XmodemTo download application file via Xmodem Uploading/Downloading Configuration Files via Tftp Downloading Application Files via TftpTo download application file via Tftp To upload application file via TftpPage Snmp Environment Snmp PrinciplesSnmp Operations Management Information Base MIB MIB Structure MIBs Supported by the IPmux-11 Snmp Agent Management Domains under Snmp Authentication Snmp CommunitiesNetwork Management Stations Index LEDs, 3-1Loopbacks OAM XMODEM, B-2 Index IPmux-11 Ver Supplement Front PanelPage Customer Response Form Excellent Good Fair Poor Very PoorPage Error Report Page Page International Headquarters