Manuals / Brands / Computer Equipment / Network Card / RAD Data comm / Computer Equipment / Network Card

RAD Data comm IPmux-11 Configuring E1 Parameters at the Physical Layer

1 148

Download 148 pages, 1.32 Mb

Installation and Operation Manual Chapter 5 Configuring IPmux-11 for a Typical Application

IPmux-11 Ver. 2.00 Configuring IPmux-11 Units 5-3

 To configure the manager list:

1. Display the Manager List menu (Configuration > System > Management >

Manager list), and enter IP parameters for the network manager station:

 NMS IP address – 192.168.10.100

 Manager location – Network-Eth1.

2. Save the changes.

Configuration>System>Management>Manager list

1. Manager IP address ... (192.168.10.100)

2. Manager location > (Network-Eth1)

3. Link up/down trap (Disable)

4. Alarm trap (Disable)

5. VLAN tagging (Disable)

>

Please select item <1 to 5>

ESC-prev.menu; !-main menu; &-exit 1 Mngr/s

Figure 5-3. Configuring Network Manager

Configuring E1 Parameters at the Physical Layer

 To configure E1 parameters at the physical layer:

1. Display the TDM (E1) Configuration menu (Configuration > Physical layer >

TDM (E1)), and configure the following parameters:

 IPmux-11 (B) transmit clock source – Loopback

 IPmux-11 (A) transmit clock source – Adaptive

 Line type – Framed G.704 CRC.

2. Save the changes.

Configuration>Physical layer>TDM (E1)

Channel ID (1)

Restoration time >(CCITT)

Signaling mode (CAS Disabled)

1. Admin status (Enable)

2. Transmit clock source >(Adaptive)

3. Rx sensitivity (Short haul)

4. Trail mode (Termination)

5. Line type >(Framed G.704 CRC)

6. Idle code[0 - ff] ... (7E)

7. Send upon fail (OOS Code)

8. OOS Code[0 - ff] (FF)

(N)

>

Please select item <1 to 11>

ESC-prev.menu; !-main menu; &-exit 1 Mngr/s

Figure 5-4. Configuring E1 at the Physical Level for IPmux-11 (A)

Contents

Main Page IPmux-11 TDM Pseudowire Access Gateway Version 2.00 Installation and Operation Manual Notice Limited Warranty Product Disposal General Safety Instructions Safety Symbols Handling Energized Products General Safety Practices Connection of AC Mains Connection of DC Mains Connection of Data and Telecommunications Cables Electromagnetic Compatibility (EMC) A ttentio FCC-15 User Information Canadian Emission Requirements Warning per EN 55022 (CISPR-22) Declaration of Conformity Quick Start Guide 1. Installing IPmux-11 Connecting the Interfaces Connecting the Power 2. Configuring IPmux-11 Configuring the IP Management Parameters Configuring E1 and T1 at the Physical Level Configuring Bundle Connections Configuring the Internal Bridge Contents Page Chapter 1 Introduction 1.1 Overview Versions Application Features E1 Interface T1 Interface Ethernet Interface IP MPLS TDMoIP Operation Modes QoS Management ConfiguRAD Timing 1.2 Physical Description 1.3 Functional Description Operation Modes Unframed Fractional Timeslot Assignment in a Bundle Testing Timing Modes Network Timing Schemes External Network Timing Single Source Clock Network Frame Format TDMoIP Page VLAN Support UDP Support TDMoMPLS Page PDVT (Jitter) Buffer PDVT Buffer Effect on Delay Packetization Delay 0.125N 47 e bytes/fram TDM Unframed Framed Round Trip Delay Reorder and Duplication of Ethernet Frames Reordering Frames ) )( ] [ ( Duplicated Frames OAM Connectivity End-to-End Alarm Generation Trail-Extended Mode VLAN Traffic Behavior Ethernet Ports Switch Operation Modes Note Rate Limiter Option Switch Behavior When Handling User and Network Traffic Table 1-12. Mode C Table 1-13. Mode D Table 1-14. Mode E Table 1-15. Mode F Table 1-16. Mode G When operating in the Mode G, the following rules apply: valid. Switch Behavior When Handling Management Traffic Table 1-17 lists operation modes of the network port when handling the management traffic. Table 1-17. Switch Behavior (Management Traffic) 1.4 Technical Specifications Page Page Chapter 2 Installation and Setup 2.1 Introduction 2.2 Site Requirements and Prerequisites 2.3 Package Contents 2.4 Connecting the Ethernet Equipment Connecting the Ethernet Network Equipment Connecting the Ethernet User Equipment 2.5 Connecting to the E1/T1 Devices 2.6 Connecting to the External Clock Source 2.7 Connecting to the ASCII Terminal 2.8 Connecting IPmux-11 to Power Connecting AC Power Connecting DC Power Page Chapter 3 Operation 3.1 Turning IPmux-11 On 3.2 Controls and Indicators Table 3-1. IPmux-11 LEDs and Controls 3.3 Default Settings Page Table 3-2. Default Settings (Cont.) 3.4 Configuration Alternatives Working with Terminal Login Page Ending a Terminal Configuration Session Working with ConfiguRAD Web Browser Requirements General Web Browsers Operating Procedures Chapter 3 Operation Installation and Operation Manual 3-10 Configuration Alternatives IPmux-11 Ver. 2.00 Overview of Menu Operations Authentication/Community User Access Host IP Management Figure 3-4. Configuration > Connection and Bridge Monitoring Statistics Status 1. Statistics 2. Status 3. Event log 1. TDM physical layer 2. Connection 3. Bridge 1. Diagnostics loopback 4. Connection Event Log 3.5 Turning IPmux-11 Off Chapter 4 Configuration 4.1 Configuration Sequence 4.2 Configuring IPmux-11 for Management Configuring IP Host Parameters Configuring DHCP Client Managing IP Parameters of the IPmux-11 Host Configuring Management Parameters Assigning a Name to IPmux-11 and Its Location Defining Read, Write and Trap Communities Defining Network Managers Page Configuration Example Local Management Remote Management Configuring Management Access Permissions and Methods Configuring User Access Controlling Management Access Configuring Control Port Parameters 4.3 Configuring IPmux-11 for Operation Configuring the System Clock Page Configuring IPmux-11 at the Physical Level Configuring the E1 TDM Interface Page Configuring the E1 External Clock Interface Configuring the T1 TDM Interface Page Page Configuring Ethernet Interfaces Not e Configuring Bundle Connections Page Page Figure 4-20. DS0 Bundle Menu Figure 4-21. Bundle Connection Menu when Connection Mode=TDMoIP CE, PSN Type=UDP/IP Configuring the Ethernet Bridge Page Status: Figure 4-23. Bridge Menu Figure 4-25. VLAN Table Menu Figure 4-24. Bridge Policy Menu 4.4 Additional Tasks Displaying the IPmux-11 Inventory Setting the Date and Time Displaying the IPmux-11 Status Displaying the Diagnostics Loopback Information Displaying the TDM Physical Layer Information Displaying the Ethernet Physical Layer Information Displaying the Bundle Connection Information Displaying the System Clock Information Transferring Software and Configuration Files Resetting IPmux-11 Resetting IPmux-11 to the Defaults Resetting IPmux-11 Page Chapter 5 Configuring IPmux-11 for a Typical Application 5.1 Overview Application Guidelines for Configuring IPmux-11 Units 5.2 Configuring IPmux-11 Units Configuring the IP Parameters Configuring E1 Parameters at the Physical Layer Configuring Bundles Figure 5-6. Connecting the Bundle for IPmux-11 (A) Page Chapter 6 Troubleshooting and Diagnostics 6.1 Monitoring Performance Displaying E1/T1 Statistics Page Table 6-1. E1/T1 Statistics Table 6-1. E1/T1 Statistics (Cont.) Displaying LAN Statistics Figure 6-2. LAN Statistics Table 6-2. LAN Statistics Parameters Displaying Bundle Connection Statistics Table 6-2. Bundle Connection Parameters Table 6-2. Bundle Connection Parameters (Cont.) 6.2 Detecting Errors Power-Up Self-Test Using Front Panel LEDs Working with the Event Log Displaying Events Page Table 6-3. Event List Table 6-3. Event List (Cont.) LOF END LOF state detected has ended Clearing Events To clear the event log: Configuring the Bundle Statistics Collection 6.3 Handling Alarms Masking Alarms 6.4 Troubleshooting 6.5 Testing IPmux-11 Running Loopbacks Running External Loopback Running Internal Loopback Page Activating T1 Inband Loopbacks Pinging IP Hosts Running a Trace Route 6.6 Frequently Asked Questions Page Page Page Page IPmux-11 Ver. 2.00 E1 and T1 Connector A-1 Appendix A Connector Wiring RJ-45 A.1 E1 and T1 Connector Balanced Connector Balanced-to-Unbalanced Adapter Cable A.2 Ethernet Connectors A.3 CONTROL Connector A.4 External Clock Connector Page Appendix B Boot Sequence and Downloading Software B.1 Booting IPmux-11 Accessing the Boot Manager B.2 Downloading the Application and Configuration Software Downloading Application Files via XMODEM Downloading Application Files via TFTP Uploading/Downloading Configuration Files via TFTP Page Appendix C SNMP Management C.1 SNMP Environment SNMP Principles SNMP Operations Management Information Base (MIB) MIB Structure MIBs Supported by the IPmux-11 SNMP Agent Management Domains under SNMP SNMP Communities Authentication Network Management Stations Index Page Page Page Supplement Drilling Template for Wall Installation Page Customer Response Form Page Error Report