196 | Standard Horizon GM29 instruction

GM29 INTEGRATOR’S MANUAL

Text Mode

Description	Command	Possible Responses

Set new message	AT+CNMI=[<mode>	• +CMS ERROR: <err>
indication to TE	[,<mt>[,<bm>[,<ds>	•	OK
	]]]]	• ERROR
		• ERROR

Shows the current	AT+CNMI?	•	+CNMI:
setting			<mode>,<mt>,<bm>,<ds>
		• OK
		• ERROR
Show if the	AT+CNMI=?	•	+CNMI:
command is			(list of supported <mode>s),
supported			(list of supported <mt>s),
			(list of supported <bm>s),
			(list of supported <ds>s)

• OK

• ERROR

Selects the procedure for the way in which new messages received from the network, are indicated to the TE when it is active, e.g. DTR signal is ON. If TE is inactive (DTR signal is OFF), message receiving is carried out as specified in GSM 03.38 (3G TS 23.038).

If the command fails and the error is related to mobile equipment or network, the final result code CMS ERROR: <err> is returned.

<mode>	Description

3	Forward unsolicited result codes directly to the TE. TA-TE
	link specific inband technique used to embed result
	codes and data when TA is in on-line data mode

<mt>	Description

0	No SMS-DELIVER indications are routed to the TE.
	No class, Class 0, class 1 and class 3 use <mem3> as
	preferred storage. Class 2 messages shall be stored in the
	SIM. If it this is not possible then the MS shall send an error
	message accordingly to GSM 03.38
1	SMS-DELIVER is stored into ME/TA and the indication of the
	memory location is routed to the TE using unsolicited result
	code:
	+CMTI: <mem>,<index>

2	Class 0, class 1, and class 3 SMS-DELIVERs are routed
	directly to the TE using the unsolicited result code:
	+CMT:<oa>, [<alpha>, <scts> [ ,<tooa>,<fo>,<pid>,<dcs>,
	<sca>,<tosca>,<length>]<CR><LF><data> (text mode
	enabled). About parameters in italics, refer to the show
	text mode command, +CSDH
3	Class 3 SMS-DELIVERs are routed directly to TE using
	unsolicited result codes +CMT:<oa>, [<alpha>, <scts> [
	,<tooa>,<fo>,<pid>,<dcs>,<sca>,<tosca>,<length>]<CR>
	<LF><data> (Text Mode enabled). About parameters in
	italics, refer to the show text mode command, +CSDH.
	Messages of other data coding schemes result in
	indication as defined in <mt>=1

196

LZT 123 7361 R1A

Image 196

Standard Horizon GM29 manual 196

Contents

GM29 Integrator’s Manual First edition October Contents Part 3 Using AT Commands Audio 129 Network 145 Short Message Services Cell Broadcast 215 Alphabetical Listing of AT Commands 261 GM29 INTEGRATOR’S Manual Part 1 Overview Page Introduction Target UsersPrerequisites Manual Structure Description GM29 ModemHighlights Main Blocks in a Wireless System GM29 in a Communication System Interface between the modem and the Application Main Features and Services Gmsk Ussd Network registration Call barring Call transfer Service and Support Precautions Abbreviations Explanations GM29 INTEGRATOR’S Manual Part 2 Integrating the Modem Page Mechanical Description Overview GM29 INTEGRATOR’S Manual Physical Dimensions Power Connector Electrical Description Audio Connector VCCHrin Toin Micn BearnBearp Micp Antenna Connector Table below shows the antenna electrical characteristics SIM Card Reader RS232 Serial Port DCDDTR GND DSR RTS CTS Serial Data Software Updates Real Time Clock Switching On the Modem Switching Off the ModemResetting the Modem Operation Operating States/LED Safety Advice and Precautions Hints for Integrating the Modem Installation of the Modem How to Install the Modem Antenna Possible communication disturbances include the following Accessories Technical Data Data Features Power Consumption Radio Specifications LED Mechanical Specification Certification Declaration of Conformity GM29 INTEGRATOR’S Manual Part 3 Using AT Commands Page Introduction to AT Commands Syntax Description ATcommandparameter AT*command=parameter AT+command parameter AT*command parameter Error Codes 2 +CMS Error Message Service Failure Result Code Examples on How to Use the AT Commands GM29 INTEGRATOR’S Manual Call Control AT+CPINPIN Control ATA No Dial Tone ATD DialBusy Dialstring Description ATO Return to Online Data Mode ATH Hang upATP Select Pulse Dialling ATT Select Tone Dialling AT+CHUP ATX Call Progress Monitoring ControlHang up Call AT+CMOD? 10 AT+CMOD Call ModeAT+CMOD=? 11 AT+CVHU Voice Hang-Up 12 AT+VTS Dtmf and Tone Generation Dtmf Ascii ATQ Result Code Suppression Control and StatusATS0 Automatic Answer Control ATS3 Command Line Termination Character ATS2 Escape Sequence CharacterATS2 ATS3? ATS4 Response Formatting Character ATS4? ATS5 Command Line Editing Character Backspace ATS6 Blind Dial Delay ControlATS5? ATS6? ATS7 Connection Completion Timeout ATS8 Comma Dial Modifier Delay ControlATS7? ATS8? 10 ATS10 Automatic Disconnect Delay Control 11 AT*ECAM Ericsson Call Monitoring AT*EDST? 12 AT*EDST Ericsson Daylight Saving TimeAT*EDST=? 13 AT*EMAR Ericsson Master Reset 14 AT*EPEE Ericsson Pin EventAT*EMAR=? AT+CLCK 16 AT+CEER Extended Error Report 15 TAT+CCLK Set Clock and Date AT+CFUN? 17 AT+CFUN Set Phone FunctionalityAT+CFUN=? AT+CIND? 18 AT+CIND Indicator ControlAT+CIND=? 19 AT+CLAC List all available AT Commands 20 AT+CMEE Mobile Equipment Error AT+CMER? 21 AT+CMER Mobile Equipment Event ReportingAT+CMER=? 22 AT+CPAS Phone Activity Status AT+CPAS=? 23 AT+CPIN PIN Control PH-SIM PIN SIM PIN2SIM PUK2 Blocked 24 AT+CPWD Change Password AT+CPWD=? GM29 INTEGRATOR’S Manual 25 AT+CR Service Reporting Control 26 AT+CRC Cellular Result Code 27 AT+CSAS Save Settings AT+CSAS=? AT+CSQ 28 AT+CSQ Signal StrengthAT+CSQ=? AT+CTZU? 29 AT+CTZU Automatic Time Zone UpdateAT+CTZU=? Audio AT*E2EAMS Ericsson M2M Audio Profile ModificationAT*E2EAMS? AT*E2EAMS=? Audio diagram of the Codec Configure current profile pr1 to pr21 Mute OFF AT*E2EAMS=255 AT*E2APR= Error AT*E2APR M2M Audio Profile ManipulationAT*E2APR? AT*E2APR=? AT*E2APR=? AT*EALR Ericsson Audio Line RequestATMS,AFMS AT*EALR? Ealr Ericsson Audio Mode Selection AT*EAMSAT*EAMS? AT*EAMS=? Ericsson Audio Ring Signal AT*EARSAT*EARS? AT*EARS=? Ericsson Local Audio Mode Ericsson Microphone ModeAT*ELAM AT*EMIC Ericsson Music Mute Indication Request AT*EMIRAT*EXVC That is no clipping occurs. An external accessory Select Bearer Service Type Data CSD/HSCSDAT+CBST AT+CBST? Name Description AT+CRLP Radio Link ProtocolAT+CRLP? +CRLP Acknowledgment timer T1 *10ms Data Gprs AT+CGACT PDP Context Activate or Deactivate+CGACT? +CGACT=? +CGATT? AT+CGATT Gprs Attach or Detach+CGATT=? AT+CGDATA Enter Data State +CGDATA=? AT+CGDCONT Define PDP Context +CGDCONT?CRLF+CGDCONT +CGDCONT=? APN +CGEREP? AT+CGEREP Gprs Event Reporting+CGEREP=? AT+CGPADDR Show PDP Address +CGPADDRCRLF+CGPAD +CGPADDR=? +CGQMIN? AT+CGQMIN Quality of Service Profile Minimum Acceptable+CGQMIN=? 117 +CGQREQ? AT+CGQREQ Quality of Service Profile Requested+CGQREQ=? 119 GM29 INTEGRATOR’S Manual AT+CGREG? AT+CGREG Gprs Network Registration StatusAT+CGREG=? +CGSMS? 10 AT+CGSMS Select Service for MO SMS Messages+CGSMS=? Data Hscsd AT+CHSCHscsd Current Call Parameters AT+CHSC AT+CHSD Hscsd Device ParametersAT+CHSD AT+CHSD=? Hscsd Non Transparent Call Configuration AT+CHSNAT+CHSN? AT+CHSN=? AT+CHSR Hscsd Parameters ReportAT+CHSR? AT+CHSR=? AT+CHSU Hscsd Automatic User Initiated UpgradingAT+CHSU? AT+CHSU=? 128 Fax AT*E2FAX Ericsson M2M Fax Comm. Baud Rate ModificationAT*E2FAX? AT*E2FAX=? Low Level Fax Commands AT&F Set to Factory Defined Configuration AT&F ErrorIdentification AT&W Store User Profile List all Supported AT Commands AT+CGMIRead MS Manufacturer Identification AT+CGMM AT+CGMR Read MS Revision IdentificationAT+CGSN Read MS Product Serial Number Identification 10 AT+GCAP Request Modem Capabilities List DTE Error InterfaceAT&C 10.3 AT&D Circuit 108 DTR Response 10.5 AT+WS46 Mode Selection 10.4 AT&S Circuit 107 DSR Response 10.6 ATE Command Echo 10.7 ATV DCE Response Format 10.8 ATZ Reset to Default Configuration AT+CMUX? 10.9 AT+CMUX Switch to 07.10 Multiplex ProtocolAT+CMUX=? 140 10.10 AT+CRES Restore SMS Settings 10.11 AT+ICF Cable Interface Character FormatAT+CRES=? AT+ICF? AT+IFC? 10.12 AT+IFC DTE-DCE Local Flow ControlAT+IFC=? 10.14 AT+IPR Cable Interface Port Command 10.13 AT+ILRR Cable Interface Local Rate Reporting AT*E2ESC? 10.15 AT*E2ESC M2M Escape Sequence Guard TimeAT*E2ESC=? Network 11.1 AT*E2CD Ericsson M2M Cell DescriptionAT*E2CD? AT*E2CD=? According to GSM 04.18 V8.6.0, the coding of the timing 11.2 AT*E2EMM Ericsson M2M Engineering Monitoring Mode AT*E2EMM=1 AT*E2EMM=7 Responses. Default value is 151 152 11.3 AT*E2SPN M2M Service Provider Indication 11.4 AT*EALS Ericsson Request ALS Status SIM 11.5 AT*ECSP Ericsson Customer Service ProfileAT*ECSP=? 11.6 AT*EPNR Ericsson Read SIM Preferred Network AT*EPNR=? 11.7 AT*EPNW 11.8 AT*E2SSN Ericsson M2M SIM Serial Number AT*ESLN? Esln 11.9 AT*ESLN Ericsson Set Line NameAT*ESLN=? 11.10 AT+CIMI Subscriber Identification 11.11 AT+CLCK +CPWD 11.12 AT+CNUM Subscriber Number AT+CNUMLF+CNUM AT+CNUM=? 11.13 AT+COLP Connected Line Identification Presentation UDIAT+COLP? AT+COLP=? Disable AT+COPS? 11.14 AT+COPS Operator SelectionAT+COPS=? AT+CREG? 11.15 AT+CREG Network RegistrationAT+CREG=? AT*ECPI? 11.16 AT*ECPI Ciphering IndicatorAT*ECPI=? 166 AT*E2NBTS? 11.17 AT*E2NBTS Ericsson M2M Neighbour BTSAT*E2NBTS=? 168 12.1 AT*E2PBCS Ericsson M2M Phonebook Check Sum Phonebook12.2 AT*ESAG Ericsson Add to Group 12.3 AT*ESCG Ericsson Create Group AT*ESCG=? 12.4 AT*ESCN AT*ESCN=? 172 12.6 AT*ESDI Ericsson Delete Group Item 12.5 AT*ESDG Ericsson Delete GroupAT*ESDI=? 12.7 AT*ESGR Ericsson Group Read 12.8 AT*EGIR Ericsson Group Item ReadAT*ESGR AT*ESGR=? 12.9 AT*ESNU Ericsson Settings Number AT*ESNU? 12.10 AT+CPBF Phonebook Find 12.11 AT+CPBR Phonebook Read+CPBF=? +CPBR=? Nlength Description AT+CPBS? 12.12 AT+CPBS Phone StorageAT+CPBS=? 12.13 AT+CPBW Phonebook Write AT+CPBW=? Tlength Description Short Message Services Point to Point 13.2 AT+CGSMS Select Service for MO SMS Messages13.1 AT+CPIN PIN Control 13.3 AT+CPMS Preferred Message Storage 182 AT+CSCA? 13.4 AT+CSCA Service Centre AddressAT+CSCA=? 13.5 AT+CMGF Message Format 13.6 AT+CMGW Write Message to MemoryAT+CMGF? AT+CMGF=? Text Mode ESC 186 13.7 AT+CMGS Send Message ESC ErrorAT+CMGS=? 188 AT+CMGF=1 AT+CSDH=1 13.8 AT+CMSS Send From Storage AT+CMSS=? +CMGC 13.9 AT+CMGC Send CommandAT+CMGC=? Text is entered ctrl-Z/ESC By toda AT+CNMI? 13.10 AT+CNMI New Message Indications to TEAT+CNMI=? No SMS-DELIVER indications are routed to the TE 196 +CBM AT+CMGR= 13.11 AT+CMGR Read MessageAT+CMGR=? +CMGR Successful and CBM storage 200 201 Compressed text not supported +CMGL 13.12 AT+CMGL List MessageAT+CMGL=? 204 AT+CMGL DELIVERs 206 207 208 13.14 AT+CSDH Show Text Mode Parameters 13.13 AT+CMGD Delete MessageAT+CMGD=? AT+CSDH? AT+CSMP? 13.15 AT+CSMP Set Text Mode ParametersAT+CSMP=? 13.16 AT+CSCS Select Character Set AT+CSCS?AT+CSCS=? IRA 13.17 AT+CSMS Select Message Service +CSMSAT+CSMS? AT+CSMS=? Short Message Services Point to Point 214 Short Message Services Cell Broadcast 14.1 AT+CNMI New Message Indications to TE14.2 AT+CSCB Select Cell Broadcast Message Type AT+CSCB? 216 AT*E2STKS SIM Application ToolkitSTK 15.3 AT*E2STKD M2M STK Display Text Display Text ErrorAT*E2STKD=? GET Inkey 15.4 AT*E2STKG M2M STK Get InkeyAT*E2STKG=? 220 Input 15.5 AT*E2STKI M2M STK Get InputAT*E2STKI=? Answer Description 223 15.6 AT*E2STKL M2M STK Select Item Select Item ErrorAT*E2STKL=? Maximum length is fixed UP Menu Error 15.7 AT*E2STKM M2M STK Set Up MenuAT*E2STKM=? GSM default alphabet 15.9 AT*E2STKC M2M STK Set Up Call Call Error15.8 AT*E2STKN M2M STK Envelope Menu Selection AT*E2STKN=? User 15.10 *E2STKE STK Send Short Message Sending an SMS 15.11 *E2STKP STK Send SS 15.12 *E2STKU STK Send Ussd 15.14 AT*E2STKTO SIM Application Toolkit Settings 15.13 *E2STKR STK Refresh Unsolicited result code *E2STKTO command 16.1 AT+CPIN PIN Control Supplementary Services16.2 AT+CACM Accumulated Call Meter AT+CAMM? 16.3 AT+CAMM Accumulated Call Meter MaximumAT+CAMM=? AT+CAOC? 16.4 AT+CAOC Advice of ChargeAT+CAOC=? 16.5 AT+CPUC Price Per Unit and Currency Table AT+CPUC?AT+CPUC=? SEK 16.6 AT*EDIF Ericsson Divert Function EdifAT*EDIF? AT*EDIF=? 16.7 AT*EIPS Identity Presentation Set AT*EIPS=IDAT*EIPS? AT*EIPS=? 16.9 AT*E2SSD M2M Supplementary Service Dispatch 16.8 AT*ELIN Ericsson Line SetAT*ELIN? AT*ELIN=? 16.10 AT*E2SSI M2M Supplementary Service Indications Ssisimerror SsinetworkproblemSsinumbererr Ssicallbarred Bearerservice TeleserviceBsallpadaccesscaservices Multiparty Bsallsynchronousservices TsalldataservicesTsallteleservicesexceptsms BS12KBITUNRESTRICTEDDIGITAL Temporarydefaultrestricted TemporarydefaultallowedSsstatusprovisioned Ssstatuspra +CCFC 16.11 AT+CCFC Call Forwarding number and ConditionsAT+CCFC=? Default value if ‘+’ is in sca AT+CCWA? 16.12 AT+CCWA Call WaitingAT+CCWA=? Unsolicited Result Codes +CCWA number, type, class 16.13 AT+CHLD Call Hold and Multiparty AT+CHLD=? AT+CLIP? 16.14 AT+CLIP Call Line Identification PresentationAT+CLIP=? Description Command Possible Responses 16.15 AT+CLIR Calling Line Identification Restriction Presentation indicator is used according to AT+CSSN? 16.16 AT+CSSN Supplementary Service NotificationAT+CSSN=? Enable the +CSSU result code presentation status in the TA AT+CUSD? 16.17 AT+CUSD Unstructured Supplementary Service DataAT+CUSD=? Different alternatives are shown below +CUSD0 OK +CUSD0,ALARM 260 Alphabetical Listing of AT Commands AT*EALR AT*EAMSAT*EARS AT*ECAM AT+CCLK AT+CCWAAT+CFUN AT+CGACT AT+CMGC AT+CMGDAT+CMGF AT+CMGR AT+CSMP AT+CSMSAT+CSSN AT+CTZU ATV ATXATZ E2STKE