4220 Flow Meter

 

 

 

Section 1 Introduction

 

 

 

 

 

 

 

 

 

 

 

 

Table 1-1 Controls, Indicators, and Connectors

 

 

 

 

 

 

 

Controls

Settings

Function

 

 

ON/OFF

On - Off

Turns the flow meter on and off. Internal memory is protected with a

 

 

 

 

standby battery. See Section 2.

 

 

 

 

 

 

 

Keypad

Momentary

24-key, four column matrix. Programs flow meter through a series of

 

 

 

Switches

keystrokes prompted by messages on the display. Certain keys per-

 

 

 

 

form specific functions (printing reports or entering program choices

 

 

 

 

into memory). Arrow keys move through menus. Number keys enter

 

 

 

 

numeric values. See Section 2.

 

 

 

 

 

 

 

Indicators

Reading

Function

 

 

Display

Multi-function

2-line, 40 characters per line, liquid crystal display (LCD). Prompts

 

 

 

 

you through program procedure; displays total flow, present flow

 

 

 

 

rate, and level. May also display parameter readings, if sensors

 

 

 

 

present.

 

 

 

 

 

 

 

Internal Plotter

Various

Provides hard copy of total flow, level or flow rate variation over

 

 

 

 

time; provides sampling information and a printout of the program.

 

 

 

 

Prints reports. Generates three different linear data plots. Chart

 

 

 

 

characters and plots are generated on plain paper roll with an ink

 

 

 

 

ribbon.

 

 

 

 

 

 

 

Connector

Type

Function

 

 

12 VDC

2-pin male M/S

Connects 12 VDC power to flow meter.

 

 

 

 

 

 

 

Sampler

6-pin male M/S

Connects flow meter to sampler; provides flow pulses to sampler;

 

 

 

 

receives sampler bottle number, composite sample, and event mark

 

 

 

 

signal.

 

 

 

 

 

 

 

Submerged Probe

5-pin, female M/S

Connects submerged probe level sensor to flow meter. Also pro-

 

 

 

 

vides connection for reference port vent tube.

 

 

 

 

 

 

 

Rain Gauge/YSI 600

9-pin Male M/S

Connects flow meter to an Isco 674 Rain Gauge or YSI 600

 

 

Sonde

(Custom)

Multi-Parameter Sonde. Also provides output to High Low Alarm

 

 

 

 

Relay Box.

 

 

 

 

 

 

 

Interrogator

6-pin female M/S

Provides serial data in/out and power. Can also be used with the

 

 

 

 

4-20 mA Output Interface and the 581 Rapid Transfer Device.

 

 

 

 

 

 

 

Modem (optional)

5-pin male M/S

Connects flow meter to telephone line for remote data transmission.

 

 

 

 

This connector will only be present on units that have the optional

 

 

 

 

modem installed.

 

 

Analog Output

6-pin male M/S

Provides analog data output from the flow meter to external,

 

 

(optional)

 

non-Isco control and recording devices.

 

 

 

 

 

 

 

Parameter

7-pin female M/S

Connects flow meter to parameter sensor: temperature, pH, or D.O.

 

 

 

 

Note that you can only have temperature and one parameter (pH or

 

 

 

 

D.O.) at the same time.

 

 

 

 

NOTE: The 270 D.O. module is no longer available from Teledyne

 

 

 

 

Isco.

 

 

 

 

 

 

1-7

Page 21
Image 21
Teledyne 4220 installation and operation guide Controls, Indicators, and Connectors, Controls Settings Function