Teledyne 4220 - page 87

4220 Flow Meter

Section 3 Installation

3-5

3.2.5 Isco Lead-Acid Battery Teledyne Isco also offers a 6.5 ampere-hour 12-volt rechargeable

lead-acid battery to power the flow meter. This battery is similar

in size to the nickel-cadmium battery, except somewhat larger,

reflecting its 50% greater capacity. For those familiar with

nickel-cadmium batteries, operation and maintenance of these

batteries differs somewhat.

• Fewer charge-discharge cycles are possible, and a single

deep discharge can ruin a battery, if you allow it to run

down all the way to the point of cell-reversal.

• There is a linear voltage decrease as the battery

discharges, while nickel-cadmium batteries show essen-

tially the same voltage throughout discharge.

• Failure to recharge promptly and low temperature

operation can also ruin the battery. Proper operation

and maintenance is necessary for normal service life.

For detailed information on these batteries, refer to the Power

Products Guide. Please read that manual if you intend to use

lead- acid batteries on your flow meter.

3.2.6 Attaching the Isco

Lead-Acid Battery

The lead-acid battery installs the same way as the

nickel-cadmium battery. Place the battery on top of the case and

secure it with the rubber draw catches. Attach the connector to

the flow meter. If your flow meter is permanently installed, you

may need to allow extra clearance above the flow meter for the

slightly greater height of this battery.

CAUTION

Do not test either type of battery for the condition of its charge

by “sparking” the output (shorting the terminals together with a

screwdriver or other tool).

3.2.7 AC Power Supplies Teledyne Isco also offers two different AC power supplies, the

High Capacity Power Pack and the Battery-Backed Power Pack

to power the flow meter. These power packs are designed for

operation from 120 Volts AC, 50/60 Hz commercial power

sources. Alternate versions, designed for operation from 240

Volts AC, 50/60 Hz are also available and are intended primarily

for export. Both are supplied with a line cord for convenient

attachment to the AC power source.

Contents

Main Page Foreword Page Page DANGER Hazard Symbols IMPORTANT PLEASE READ WARNING killed. Never Page Table of Contents i Section 1 Introduction Section 2 Programming Section 3 Installation Section 4 Submerged Probe Installation Section 5 Options and Accessories iii Section 6 Maintenance and Service Appendix A Replacement Parts Appendix B Accessories List Appendix C Programming Worksheets iv Appendix D General Safety Procedures Appendix E Material Safety Data Sheets List of Illustrations v List of Tables Page Section 1 Introduction 1.1 Description 1.2 Compatible Equipment 1.3 Operating Principles Page 1.4 Software Upgrades 1.5 Controls, Indicators, and Connectors Page Page 1-7 Table 1-1 Controls, Indicators, and Connectors Controls Settings Function Indicators Reading Function Connector Type Function 4220 Flow Meter 1.6 Technical Specifications Table 1-2 Technical Specifications for the 4220 Flow Meter Physical Specifications 1-9 Flow Conversion Table 1-2 Technical Specifications for the 4220 Flow Meter (Continued) Table 1-3 Technical Specifications for the 3222 Submerged Probe Physical Specifications Level Measurement Specifications 1.7 How to Make Battery Calculations Table 1-5 Battery Life Expectancy Page Page 00I5 + Page Section 2 Programming 2.1 Getting Started Page 2.2 Programming Procedure Page 2.3 Description of Program Steps Page Page Page Page Page 2.4 Interpreting the Program Screens Page Page Page Page Page Page Table 2-1 ASCII Output Codes Table 2-1 ASCII Output Codes (Continued) Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Section 2 Programming 2-41 Figure 2-3 YSI 600 Sonde Calibration Flow Chart Page Page Page Page Page Page Page Page Page Page Page Page Page Section 3 Installation 3.1 Introduction Page 3.2 Connection to a Power Source Page Page Page 3.3 Flow Meter Mounting and Installation Procedures 3.4 Quick-Disconnect Box Page 3.5 Extension Cables 3.6 Safety Considerations 3.7 Isco Sampler Interface Page Section 4 Submerged Probe Installation 4.1 General Mounting Considerations 4.2 Submerged Probe Nose Sections 4.3 Mounting Rings Page Page Page Page Flow Page 4.4 Other Mounting Techniques Table 4-1 Locating the Head-Measuring Point Page Page Page Section 5 Options and Accessories 5.1 4200T Modem Page Page 5.2 Connection to External Serial Device 5.3 4-20 mA Analog Outputs: External and Internal Table 5-1 4-20 mA Output Interface Specifications Table 5-1 4-20 mA Output Interface Specifications 5.4 Tipping Bucket Rain Gauge Table 5-2 Multiple Analog Output Board Specifications 5.5 Isco Flowlink Software 5.6 High-Low Alarm Relay Box DANGER 5.7 Parameter Sensing with Isco 4200 Series Flow Meters 5.8 The Temperature Probe 5.9 The pH Probe Page Page Page Page Page Table 5-3 pH Probe Specifications 5.10 The Dissolved Oxygen (D.O.) Probe Note Page Page Page Table 5-4 D.O. Probe Specifications 5.11 Installation of Parameter Probes in Mounting Rings 5.12 The YSI 600 Multiple Parameter Sonde Table 5-5 YSI 600 Probe Specifications 5.13 Mechanical Totalizer Table 5-5 YSI 600 Probe Specifications (Continued) Section 6 Maintenance and Service 6.1 Routine Maintenance and Minor Service 6.2 Reactivation of the Desiccators Page 6.3 Care of the Submerged Probe and Cables Page Page 6.4 Maintenance of the Printer Page Page 6.5 Servicing And Troubleshooting Page Page 6.6 Preliminary Troubleshooting Steps Page 6.7 Precautions for Servicing CMOS Circuitry 6.8 Using FLASH UPDATE Page Page Page Table 6-1 Minimum DOS and Computer Hardware Requirements Appendix A Replacement Parts Page Page Appendix A Replacement Parts A-4 Table A-1 Replacement Parts List No Part Num ber Complete Part Description Table A-1 Replacement Parts List (Continued) Page Appendix B Accessories List Page Page Page Appendix C Programming Worksheets C.1 Setup Page C.2 Flow Conversion: Level-to-Flow Rate C.3 Parameter to Adjust C.4 Reset Totalizer C.5 Sampler Pacing C.6 Sampler Enable C.7 Alarm Dialout Mode C.8 Printer C.9 Reports/History Page Page Appendix D General Safety Procedures D.1 Practical Safety Precautions Page Page D.2 Lethal Atmospheres in Sewers Page D-6 D.3 Hazardous Gases hazardous gases. Table D-1 Hazardous Gases D-7 D-8 D-9 Page Page E-2 *Optional Indicating Silica Gel Material Safety Data Sheet Buffalo, NY 14224 Section 1 - Material Identification and Information Section 2 - Physical/Chemical Characteristics Section 3 - Fire and Explosion Hazard Data E-3 *Optional Indicating Silica Gel Section 5 - Health Hazard Data Section 6 - Control and Protective Measures Section 7 - Precautions for Safe Handling and Use/Leak Procedures Section 1 Product and Company Information Section 2 Composition / Information on Ingredients Section 3 Hazard Identification E-5 Section 4 First Aid Measures Section 5 Fire Fighting Measures Section 6 Accidental Release Measures Section 7 Handling and Storage E-6 Section 8 Exposure Controls/Personal Protection Component Name Exposure Limits Section 9 Physical and Chemical Properties Section 10 Stability and Reactivity E-7 Section 11 Toxicological Information Section 12 Ecological Information Section 13 Disposal Information Section 14 Transportation Information Section 15 Regulatory Information Section 16 Other Information Index-1 Index Numerics A B C P Q R S T DECLARATION OF CONFORMITY Page CE Declaration of Conformity DECLARATION OF CONFORMITY Page Teledyne Isco One Year Limited Factory Service Warranty *