Figure A-3. Login Prompt | ADC MM702G2, MM701G2 specification

Appendix A: Command Line Interface Access

April 14, 2006

Step		Action
5	In the COM1 Properties dialog, enter the Port Settings as follows:
	•	9600 baud
	•	8 data bits
	•	no parity
	•	1 stop bit
	•	flow control off (none)

6	Click OK.

7	Press ENTER. A prompt will be displayed (see Figure A-3); enter your login and password.

Modem Defaults

Login admin

Password password

Figure A-3. Login Prompt

The System Management main menu is displayed (Figure A-4).

Figure A-4. System Management Main Menu

Type the number and press ENTER to access the configuration menu for each parameter (WAN Session Management or LAN Management, for example). Press ENTER (<CR>) at the prompt to return to a higher-level menu.

A-4	MM70xG2-UM-03

Image 92

ADC MM702G2, MM701G2 user manual Figure A-3. Login Prompt

Contents

Megabit Modem MM701G2 & MM702G2 Revision History Table of Contents Configuring NAT Appendix C Product Support Glossary GL-1 Table of Contents April 14 MM70xG2-UM-03 List of Figures 10.RFC1483 Bridged Session Figure A-7. WAN Session Management List of Figures April 14 MM70xG2-UM-03 List of Tables List of Tables April 14 Xii MM70xG2-UM-03 About this Manual IntroductionOrganization Intended Audience EU Compliance Inspecting Your ShipmentFCC Class B Compliance Unpack the Modem InstallationOverview Switch, or router Determine What YOU NeedRequired Equipment Equipment Requirement Connect Cables Connect the 10/100Base-T Port Rear Panel Connections State Description LED Status IndicatorsLED Status Indications Rebooting the Modem with the Reset Button Reboot the Modem with the Reset Button Accessing the WEB Interface for Modem Management Assign IP Addresses SET UP the WEB Browser Internet Options Accessing the Modem WEB Pages Select the Use a proxy server box Enter User Name and Password Before YOU Begin Configuring the LANConfigure the LAN Configure DNS Relay Mode LAN ProtocolIP Address Subnet Mask April 14 Provisioning Configure Dhcp Server Mode Dhcp Server Mode Internet Protocol TCP/IP Properties Default Lease Time Dhcp Default GatewayDhcp Range Low Dhcp Range High Configuring the WAN LLC Configure a NEW WAN Session WAN Configuration Set Up an RFC 1483 Bridged Session RFC 1483 Bridged Session Session Name Virtual Path ID VPIVirtual Channel ID VCI ATM QoS Set Up an RFC 1483 Routed Session RFC 1483 Routed Session Dhcp Client RIP Accept Set Up a PPPoA or PPPoE Routed SessionRIP Send LLC Header Authentication LoginPassword Permanently Save Sessions Edit a WAN Session WAN Sessions Routing WAN Sessions PPP Before You Begin Configuring System ParametersAssigning User Access Access Level User Access LevelsUser Name Comment User Configuration ADD a Default Gateway Default Gateway ADD Static Route Entries Static Routes Destination GatewayNetmask Cost Delete Route ADD Snmp Communities Snmp Community List Access Privilege Name Change Spanning Tree Setting 10. Delete Snmp Community Forward Delay Spanning TreePriority Hello Time Saving Changes 12. Save Changes 13. Configuration Save Complete Rebooting the Modem 14. Reboot Configuring DSL Parameters Complete a G.SHDSL Quick Configuration Operating Mode Bit Rate ModeStandard Annex Startup Margin Complete a DSL Advanced Configuration G.SHDSL Advanced Configuration Data Rate kbps Wire Pair ModePower Spectrum Distribution Test Bit Rate SNR Margin Limit Configuring DSL Parameters April 14 MM70xG2-UM-03 Complete a Quick Installation Implementing a POINT-TO-POINT LAN Extension Configure for Central-Office Mode Change the LAN IP Address for the Central-Office Modem Http//10.0.0.2 to reconnect Complete a Custom ConfigurationConfigure the Remote Modem Step LAN Configuration-Configure Remote LAN Click Save to save the configuration to flash memory Configure the Central-Office Modem 10. RFC1483 Bridged Session 11. LAN Configuration-Configure CO LAN Verify Connectivity 12. Save Changes-CO LAN 13. ATM Statistics Configuring NAT Configure NAT Firewall-Add Interface View Modem Status Managing the ModemView System Status View System Log Configuration Error Log View WAN Statistics View LAN Statistics Rx PktsRx Bad Pkts Tx Pkts Rx CRC Errors Tx Collisions View Smartcnct Security Statistics Security EnabledNAT Enabled View ATM Statistics View DSL Statistics View G.shdsl Link Statistics Transmission Power Operational StateData Rate Receiver Gain View G.shdsl Error Counters Manage Software and Configuration Update System Software 10. Updating Flash 12. Restore Factory Defaults-Web Interface 13. Restore Factory Defaults-Reset Button Command Line Interface Access Section Connect to the Console Port Access through the Console Port Figure A-2. COM1 Properties Figure A-3. Login Prompt Access Through a Telnet Session Figure A-5. Windows Telnet Set Up the LAN Figure A-6. LAN Configuration System Default Gateway Ethernet ModeLAN IP Address LAN Subnet Mask Manage WAN Sessions Figure A-7. WAN Session Management Add a New Session Figure A-8. Create New Session QoS Class Peak Cell RateSustain Cell Rate Maximum burst size Figure A-9. RFC 1433 Routed Session WAN Dhcp Enable RIP Accept ModeRIP Send Mode WAN IP Address Figure A-10. PPPoA Routed Session LLC header mode Edit an Existing Session PPP AuthenticationUser Password Figure A-12. PPPoA Routed Session Manage DSL Figure A-13. DSL Management Menu Configure G.shdsl Parameters Figure A-14. G.SHDSL Quick Configuration Operating Mode Noise on the line. The default is -10 dB for the modem PSD Mode View G.shdsl Configuration Figure A-16. G.SHDSL Current Setting Menu Figure A-17. Quick Configuration Setting Menu Monitor G.shdsl Statistics View the current statistics, as described below Figure A-19. G.SHDSL Error Counters CRC Error Figure A-20. ATM Statistics Menu Restoring Factory Defaults Figure A-21. Restoring Factory Defaults Saving the Current Configuration Figure A-22. Save Current Configuration Updating System Software Viewing System Information From the Main Menu, enter 8 to Reboot Specifications Appendix B Data Specifications PPP Default Session Parameter Values PCR Hardware Specifications LED Connector Pinouts Table B-1. DSL Port RJ-11 2-Wire Pin SignalTable B-2. DSL Port RJ-11 4-Wire Pin Signal DSL Port RJ-11 Signal Description PC RS-232 Console Serial DB-9 RJ-45 Signal DescriptionTable B-3 /100Base-T Port RJ-45 Table B-4. Console Port RJ-45 Rate VS Reach Product Support Appendix C Product Support April 14 MM70xG2-UM-03 Symbol Glossary GL-2 MM70xG2-UM-03 MM70xG2-UM-03 GL-3 GL-4 MM70xG2-UM-03 Certification and Warranty World Headquarters For Technical Assistance