Manage Software and Configuration | ADC MM701G2, MM702G2 manual

April 14, 2006

Chapter 9: Managing the Modem

Step

Action

3Click one of the following:

•Clear—resets all the counters to zero.

•Refresh—updates the page with current error counts.

MANAGE SOFTWARE AND CONFIGURATION

Update System Software

Using the Web interface HTTP Upgrade capability, you can upgrade the software image (.tar). To complete an upgrade, specify the IP address of a server on the LAN side of modem where the new firmware is stored.

IMPORTANT

!

The software update process takes about 90 seconds to complete and after the update the modem resets itself. Do not recycle the power during this process. This will cause permanent image corruption.

It is strongly recommended that you use this procedure to upgrade software.

Step

Action

1Click System on the menu bar, then Software Update under System to access the Software Update page (Figure 9-9).

Figure 9-9. Software Update

2Click Browse, locate the server on the LAN where the firmware image or configuration file is located, then click Open.

3Click Upload to start the file transfer to the modem.

	IMPORTANT	Do not power cycle the modem when the software update is in progress. Wait for the
	!
	!	“Flash Update Complete” message before power cycling the modem.

MM70xG2-UM-03

9-11

Image 85

ADC MM701G2, MM702G2 user manual Manage Software and Configuration, Update System Software

Contents

Megabit Modem MM701G2 & MM702G2 Revision History Table of Contents Configuring NAT Appendix C Product Support Glossary GL-1 Table of Contents April 14 MM70xG2-UM-03 List of Figures 10.RFC1483 Bridged Session Figure A-7. WAN Session Management List of Figures April 14 MM70xG2-UM-03 List of Tables List of Tables April 14 Xii MM70xG2-UM-03 Introduction About this ManualOrganization Intended Audience FCC Class B Compliance Inspecting Your ShipmentEU Compliance Overview InstallationUnpack the Modem Determine What YOU Need Switch, or routerRequired Equipment Equipment Requirement Connect the 10/100Base-T Port Connect Cables Rear Panel Connections LED Status Indications LED Status IndicatorsState Description Reboot the Modem with the Reset Button Rebooting the Modem with the Reset Button Assign IP Addresses Accessing the WEB Interface for Modem Management Internet Options SET UP the WEB Browser Select the Use a proxy server box Accessing the Modem WEB Pages Enter User Name and Password Configure the LAN Configuring the LANBefore YOU Begin LAN Protocol Configure DNS Relay ModeIP Address Subnet Mask April 14 Provisioning Dhcp Server Mode Configure Dhcp Server Mode Internet Protocol TCP/IP Properties Dhcp Default Gateway Default Lease TimeDhcp Range Low Dhcp Range High LLC Configuring the WAN WAN Configuration Configure a NEW WAN Session RFC 1483 Bridged Session Set Up an RFC 1483 Bridged Session Virtual Path ID VPI Session NameVirtual Channel ID VCI ATM QoS RFC 1483 Routed Session Set Up an RFC 1483 Routed Session Dhcp Client RIP Send Set Up a PPPoA or PPPoE Routed SessionRIP Accept LLC Header Login AuthenticationPassword Permanently Save Sessions Edit a WAN Session WAN Sessions Routing WAN Sessions PPP Assigning User Access Configuring System ParametersBefore You Begin User Access Levels Access LevelUser Name Comment User Configuration Default Gateway ADD a Default Gateway Static Routes ADD Static Route Entries Gateway DestinationNetmask Cost Delete Route Snmp Community List ADD Snmp Communities Name Access Privilege 10. Delete Snmp Community Change Spanning Tree Setting Spanning Tree Forward DelayPriority Hello Time 12. Save Changes Saving Changes 13. Configuration Save Complete 14. Reboot Rebooting the Modem Complete a G.SHDSL Quick Configuration Configuring DSL Parameters Bit Rate Mode Operating ModeStandard Annex Startup Margin G.SHDSL Advanced Configuration Complete a DSL Advanced Configuration Power Spectrum Distribution Wire Pair ModeData Rate kbps SNR Margin Limit Test Bit Rate Configuring DSL Parameters April 14 MM70xG2-UM-03 Implementing a POINT-TO-POINT LAN Extension Complete a Quick Installation Change the LAN IP Address for the Central-Office Modem Configure for Central-Office Mode Configure the Remote Modem Complete a Custom ConfigurationHttp//10.0.0.2 to reconnect Step LAN Configuration-Configure Remote LAN Configure the Central-Office Modem Click Save to save the configuration to flash memory 10. RFC1483 Bridged Session 11. LAN Configuration-Configure CO LAN 12. Save Changes-CO LAN Verify Connectivity 13. ATM Statistics Configure NAT Configuring NAT Firewall-Add Interface View System Status Managing the ModemView Modem Status View System Log View WAN Statistics Configuration Error Log Rx Pkts View LAN StatisticsRx Bad Pkts Tx Pkts Tx Collisions Rx CRC Errors NAT Enabled Security EnabledView Smartcnct Security Statistics View ATM Statistics View G.shdsl Link Statistics View DSL Statistics Operational State Transmission PowerData Rate Receiver Gain View G.shdsl Error Counters Update System Software Manage Software and Configuration 10. Updating Flash 12. Restore Factory Defaults-Web Interface 13. Restore Factory Defaults-Reset Button Section Command Line Interface Access Connect to the Console Port Figure A-2. COM1 Properties Access through the Console Port Figure A-3. Login Prompt Figure A-5. Windows Telnet Access Through a Telnet Session Figure A-6. LAN Configuration Set Up the LAN Ethernet Mode System Default GatewayLAN IP Address LAN Subnet Mask Figure A-7. WAN Session Management Manage WAN Sessions Figure A-8. Create New Session Add a New Session Peak Cell Rate QoS ClassSustain Cell Rate Maximum burst size Figure A-9. RFC 1433 Routed Session RIP Accept Mode WAN Dhcp EnableRIP Send Mode WAN IP Address Figure A-10. PPPoA Routed Session LLC header mode User Password PPP AuthenticationEdit an Existing Session Figure A-12. PPPoA Routed Session Figure A-13. DSL Management Menu Manage DSL Figure A-14. G.SHDSL Quick Configuration Configure G.shdsl Parameters Operating Mode Noise on the line. The default is -10 dB for the modem PSD Mode Figure A-16. G.SHDSL Current Setting Menu View G.shdsl Configuration Monitor G.shdsl Statistics Figure A-17. Quick Configuration Setting Menu View the current statistics, as described below CRC Error Figure A-19. G.SHDSL Error Counters Figure A-20. ATM Statistics Menu Figure A-21. Restoring Factory Defaults Restoring Factory Defaults Figure A-22. Save Current Configuration Saving the Current Configuration Viewing System Information Updating System Software From the Main Menu, enter 8 to Reboot Appendix B Specifications Data Specifications PPP PCR Default Session Parameter Values LED Hardware Specifications Table B-1. DSL Port RJ-11 2-Wire Pin Signal Connector PinoutsTable B-2. DSL Port RJ-11 4-Wire Pin Signal DSL Port RJ-11 PC RS-232 Console Serial DB-9 RJ-45 Signal Description Signal DescriptionTable B-3 /100Base-T Port RJ-45 Table B-4. Console Port RJ-45 Rate VS Reach Product Support Appendix C Product Support April 14 MM70xG2-UM-03 Glossary Symbol GL-2 MM70xG2-UM-03 MM70xG2-UM-03 GL-3 GL-4 MM70xG2-UM-03 Certification and Warranty For Technical Assistance World Headquarters