Program Mode Continued

Initialize New Firmware

After new firmware is installed, the control must be initialized to the new firmware version and memory locations. Use the following procedure to Initialize the firmware.

Action

Description

 

 

Display

Comments

 

 

 

 

 

 

 

 

Apply Power

Keypad Display shows this

 

 

 

 

Logo display for 5 seconds.

 

 

 

 

opening message.

 

 

 

 

 

 

If no faults and programmed for

 

 

 

 

 

Display mode. Stop LED on.

 

 

 

 

 

 

 

 

 

 

LOCAL operation.

 

 

 

 

 

Press PROG key

Enter program mode.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Press Y or B key

Scroll to Level 2 Blocks.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Press ENTER key

Select Level 2 Blocks.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Press Y or B key

Scroll to the Miscellaneous block.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Press ENTER key

Select Miscellaneous block.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Press Y key

Scroll to Factory Settings

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

parameter.

 

 

 

 

 

Press ENTER key

Access Factory Settings

 

 

 

 

 

V represents blinking cursor.

 

 

 

 

 

 

 

 

parameter.

 

 

 

 

 

Press Y key

Scroll to YES, to choose original

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

factory settings.

 

 

 

 

 

Press ENTER key

Restores factory settings.

 

 

 

 

 

“Loading Presets” is first message

 

 

 

 

 

 

 

 

 

 

 

 

 

 

“Operation Done” is next

Press Y key

Scroll to menu exit.

 

 

 

 

 

“No” is displayed last.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Press ENTER key

Return to display mode.

 

 

 

 

 

Display mode. Stop LED on.

 

 

 

 

 

 

 

 

 

Press DISP key several

Scroll to diagnostic information

 

 

 

 

 

If you wish to verify the software

 

 

 

 

 

 

 

times

screen.

 

 

 

 

version, enter diagnostic info.

Press ENTER key

Access diagnostic information.

 

 

 

 

Displays commanded speed,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

direction of rotation, Local/

 

 

 

 

 

 

 

Remote and motor speed.

 

 

 

 

 

 

 

Press DISP key

Display mode showing software

 

 

 

 

Verify new firmware version.

 

 

 

 

version and revision installed in

 

 

 

 

 

 

the control.

 

 

 

 

 

 

 

 

 

 

Press DISP key

Displays exit choice.

 

 

 

 

Press ENTER to exit diagnostic

 

 

 

 

 

 

 

 

 

 

information.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MN722

Programming & Operation 4-9

Page 56
Image 56
Baldor mn722 manual Initialize New Firmware