Happens? What to Do? | Compaq Infortrend specs

2-Line LCD Power Supply Unstable or NVRAM Failed

Terminal [0114] Controller ALERT: Power Supply Unstable or NVRAM Failed

Event Type

!Alert

"Warning

"Notification

What The output voltage drops below preset thresholds or NVRAM Happens? component failure.

What to

Do?

Warning:

2-Line LCD Memory Not Sufficient to Fully Support Current Config.

Terminal [0107] Memory Not Sufficient to Fully Support Current Config.

Event Type

"Alert

!Warning

"Notification

What The installed size of memory does not support current configuration. Happens? Try increase memory size.

What to

Do?

Notification:

2-Line LCD Controller Initialization Completed

Terminal [0181] Controller Initialization Completed

Event Type"Alert "Warning !Notification

What Controller initialization completed

Happens?

What to

Do?

2-Line LCD Memory is Now Sufficient to Fully Support Current Config.

Terminal [0187] Memory is Now Sufficient to Fully Support Current Config.

Event Type"Alert "Warning !Notification

What Memory size has been expanded.

Happens?

What to

Do?

2-Line LCD NVRAM Factory Defaults Restored

Terminal [0189] NVRAM Factory Defaults Restored

Event Type

"Alert

"Warning

!Notification

What Firmware settings have been restored to factory defaults. Options for Happens? restoring defaults are not available to users and are only reserved for

qualified engineers.

What to

Do?

D-8	Infortrend

Image 308

Compaq Infortrend manual Happens? What to Do?

Contents

External RAID Controller & Subsystem Revision Firmware Version Copyright This Edition First Published Disclaimer Supported Models IiiRMA Policy Table of Contents LCD Screen Messages LCD Keypad Operation Viewing and Editing Logical Drives and Drive Members Viewing and Editing Scsi Drives Vii Terminal Screen MessagesTerminal Operation Fibre Operation Viii Host-side and Drive-side Scsi Parameters Advanced ConfigurationMulti-Host Access Control LUN Filtering Redundant Controller 10-110-14 10-19 Record of Settings Array Expansion Xii Appendix C System Functions Upgrading FirmwareAppendix D Event Messages Functional Table of Contents Xiv 7.8 Chapter Advanced Configurations Chapter Fibre Operation Xvi Chapter Redundant Controller ConfigurationChapter Array Expansion Appendix C Controller Maintenance Xvii Xviii Chapter Optimization Setting Xix About This Manual Revision History Xxi Xxii Logical Volume What is a logical volume?Logical Drive Chapter RAID Levels What are the RAID levels?RAID Levels Infortrend LogicalDrive RAID 0+1 RAID 0+1 Disk Striping with Dedicated Parity Disk Spare Drives Global and Local Spare DrivesLocal Spare 12 Mixing Local and Global Spares Identifying Drives Flash Selected Scsi DriveFlash All Scsi Drives Flash All but Selected Drives Rebuild Automatic Rebuild and Manual Rebuild Manual Rebuild 14 Manual Rebuild Concurrent Rebuild in RAID 0+1 Logical Volume Multi-Level RAID 15 Logical Volume 16 Logical Drive Composed of 24 Drives Spare drives assigned to a logical volume? 18 Logical Volume with Drives on Different Channels Limitations Different controller settings using logical volume? Different write policies within a logical volume?RAID expansion with logical volume? Logical volume with logical drives of different levels? Multi-level RAID systems RAID Planning How many physical drives do you have?How many drives on each drive channel? Dual loop, hub, or switch? What kind of host application? Optimization Mode What RAID level? Any spare drives? Limitations? Array Configuration Process Starting a RAID System Infortrend 1 I/O Channel, Scsi ID, and LUN Grouping Drives into an Array Physical locations of drive members Making Arrays Available to Hosts Mapping Partitions to Host ID/LUNs Controller Parameter Settings Tunable Parameters Optimization Mode Array Configuration Out-of-Band via Serial Port and Ethernet Following are guidelines on using the serial portRS-232C Serial Port Configuring RS-232C Connection via Front Panel Starting RS-232C Terminal Emulation Keys used when operating via the terminal are as followsConnecting Terminal What Is the Disk Reserved Space? Out-of-Band via Ethernet Requirements Connecting Ethernet PortOther Concerns Configuring the Controller Use a Terminal Emulator to Begin Configuration Assign an IP Address to Ethernet Port Starting the Manager NPC Onboard Snmptrap Snmptrap section LCD Screen Messages Quick Installation ScreenInitial Screen Logical Drive Status Logical DriveRAID level Drive numbers Logical Volume Status Logical Volume Status Scsi Drive Status Channel Mode Default Scsi Bus Sync ClockScsi Channel Status Primary Controller Scsi ID Mapping Controller Voltage and Temperature UPS Power Failure Detected Press 2 Seconds to Clear Events Cache Dirty PercentageView and Edit Event Logs View and Edit Event Logs Power on RAID Enclosure Caching ParametersOptimization Modes Front Panel Operation Optimization Mode and Stripe Size Database and Transaction-based Applications Optimization for Random or Sequential I/O Write-Back/Write-Through Cache Enable/DisableWrite-Back Cache Enabled Disable Write Infortrend View Connected Drives View and Edit Scsi Drives=2 I=0 1010MB New DRV Seagate View Drive Information Creating a Logical Drive Choosing a RAID LevelChoosing Member Drives Logical Drive Preferences Initialization Mode Maximum Drive CapacitySpare Drive Assignments Disk Reserved Space Stripe size Default ? On-Line ModeStripe Size Beginning Initialization Off-Line Mode Creating a Logical Volume Logical Volume Assignment Partitioning a Logical Drive/Logical Volume Mapping a Logical Volume/Logical Drive to Host LUN View Edit Host Luns Assigning Spare Drive and Rebuild Settings Adding a Local Spare DriveMAP to LV=0 PRT=0? View and Edit Scsi Drives =2 I=4 1010MB Add Global Spare Drive Add Global Spare Drive Successful Rebuild SettingsAdding a Global Spare Drive Viewing and Editing Logical Drives and Drive Members Deleting a Logical Drive Deleting a Partition of a Logical Drive Drive Space Allocated to the Last Partition Assigning a Name to a Logical Drive Rebuilding a Logical DriveView and Edit Logical Drives LG0 RAID5 DRV=3 2012MB FL SB=0 Rebuild Logical Drive Drive? Rebuilding 25% Please Wait Regenerating Logical Drive Parity LG0 RAID5 DRV=3 2012MB RB SB=0 Rebuild Progress Media Scan View and Edit Logical Drives LG0 RAID5 DRV=3 4095MB GD SB=0 Write Policy Viewing and Deleting LUN Mappings Pass-through Scsi CommandsViewing and Editing Host LUNs Scan Channel=1 ID=1 Scan Fail Viewing and Editing Scsi DrivesScanning New Scsi Drive Identifying a Drive =1 I=1 Absent Deleting Spare Drive Global / Local Spare Drive Redefining Channel ModeViewing and Editing Scsi Channels Setting a Scsi Channel’s ID Host Channel Viewing IDs Adding a Channel IDAdd Channel Primary Controller ? Add CHL=0 ID=2 Primary Ctlr ? Setting a Scsi Channel’s Primary ID Drive Channel Deleting a Channel IDDelete Channel Delete ID=2 Primary Ctlr ? Setting a Scsi Channel’s Secondary ID Drive Channel Setting Channel Bus Terminator Setting Transfer Speed Scsi Terminator Enabled CHL=0 Disable Terminator ? Setting Transfer Width Viewing and Editing Scsi Target Drive ChannelView and Edit Scsi Channels CH1=Drive PID=7 View and Edit Scsi Target Maximum Transfer Width Slot NumberMaximum Synchronous Transfer Clock Disconnecting Support Parity CheckMaximum Tag Count Max Xfer Narrow Only? Restore to Default Setting Change Password Changing PasswordSystem Functions Mute Beeper Shutdown Controller Disabling PasswordReset Controller Restore Nvram from Disks ShutdownComplete Reset Ctlr?Controller Maintenance Save Nvram To Disks Restore Nvram From Disks Password Validation Timeout Controller ParametersController Name LCD Title Display Controller Name Time Zone Controller Date and TimeTime Zone Date and Time MMDDhhmmYYYY Date and TimeGMT +0800 Scsi Drive Utilities Scsi Drive Low-level FormatView and Edit Scsi Drives =1 I=1 8683MB Scsi Drives Utilities Drive Read/Write Test Scsi Drive Read/Write Test Transfer Rate Indicator PC Graphic Ansi ModeTerminal VT-100 Mode Cursor Bar Quick Installation Main Menu Terminal Screen Messages SizeMB Status Column C Name Slot ChlSize MB Speed Scsi Channel’s Status PID CurWid TermCurSynClk Controller voltage and temperature monitoring Viewing Event Logs on the Screen Terminal Operation Terminal Operation Limitations Optimization Mode and Stripe Size Viewing the Connected Drives Creating a Logical Drive Choosing a RAID Level Assign Spare Drives Logical Drive Assignments Initialization Mode Terminal Operation Creating a Logical Volume Partitioning a Logical Drive/Logical Volume Infortrend Mapping a Logical Volume to Host LUN Infortrend Assigning Spare Drive, Rebuild Settings Adding Local Spare Drive Viewing and Editing Logical Drive and Drive Members 1000MB Rebuilding a Logical Drive Applies to RAID1, 3, Iteration Count Viewing or Deleting LUN Mappings Edit Host-ID/WWN Name List Scanning New Drive Slot Number Drive Entry Identifying Drive Terminal Operation Viewing and Editing Scsi Channels Viewing and Editing Scsi IDs Host Channel Setting a Primary Controller’s Scsi ID Drive Channel Deleting an ID Setting a Secondary Controller’s Scsi ID Drive Channel Setting Channel TerminatorSetting a Transfer Speed Drive Channel Setting the Transfer Width Host Channel Viewing and Editing Scsi Target / Drive Channel Maximum Synchronous Transfer Clock Data Rate Infortrend System Functions Changing the Password Setting a New Password Disabling the Password Controller Parameters Saving Nvram to Disks Password Validation Timeout Terminal Operation Set Controller Date and Time View Drive Information Drive InformationScsi Drive Utilities Scsi Drive Low-level Format Scsi Drive Read/Write Test Overview Fibre Operation Major Concerns Fibre Operation Multiple Target IDs Supported FeaturesFibre Chip Drive IDs In-band Fibre and S.E.S. Support Primary and Secondary Controller IDs Configuration Host and Drive ParametersChannel Mode Limitation Redundant Controller Cache Coherency Channel RCC ChannelView Channel WWN User-Assigned ID Scan Scsi Drive View Device Port Name List WwpnView and Edit Fibre Drive View and Edit Host-Side Parameters Fibre Channel Connection Type View and Edit Drive-Side Parameters Drive-Side Dual Loop Controller Unique Identifier Controller Communications over Fibre Loops Fibre Operation Multi-Host Access Control LUN Filtering Storage Pool Creating LUN Masks Host-LUN Mapping WWN Name List Logical Unit to Host LUN Mapping Infortrend LUN Mask ID Range Configuration Filter Type Include or Exclude Sample Configuration Access Mode Read Only or Read/Write Configuration Procedure Infortrend A.R.T Fault PreventionAdvanced Configurations Clone Failing Drive Replace after Clone Perpetual Clone Advanced Configurations Introduction Disable Detect OnlyPerpetual Clone Clone + Replace Examining Whether Your Drives Support S.M.A.R.T Configuration ProcedureEnabling the S.M.A.R.T. Feature Using S.M.A.R.T. Functions Detect Only Setting Detect, Perpetual Clone Setting Detect, Clone+Replace Function Foreword Scsi Channel, Scsi ID and LUN Host-side and Drive-side Scsi ParametersHost-side Scsi Parameters Number of Tags Reserved for each Host-LUN Connection LUN Applicability Maximum Queued I/O CountLUNs per Host Scsi ID In-band Scsi or Fibre What is In-band?Peripheral Device Type Peripheral Device Type Parameters SCO Peripheral Device Type Settings Device Type SettingCylinder/Head/Sector Mapping Cylinder/Head/Sector Mapping under Sun Solaris Configuring Sector Ranges/Head Ranges/Cylinder Ranges Drive-side Parameters Scsi Motor Spin-Up Scsi Reset at Power-Up Disk Access Delay Time Scsi I/O Timeout Maximum Tag Count Tag Command Queuing Periodic Drive Check Time Detection of Drive Hot Swap Followed by Auto RebuildSAF-TE and S.E.S. Enclosure Monitoring Idle Drive Failure Detection Periodic Auto-Detect Failure Drive Swap Check Time Advanced Configurations View Peripheral Device Status Monitoring and Safety MechanismsDynamic Switch Write-Policy Controller Auto-Shutdown Event Trigger Option Disk Array Parameters Rebuild Priority Verification on Writes Operation Theory Redundant Controller 10-1 Setup Flowchart Considerations Related to Physical ConnectionSCSI-Based Controllers 10-2 Infortrend Fibre-Based Controllers Redundant Controller 10-3 Grouping Hard Drives and LUN Mapping 10-4 Infortrend Logical Drive, Logical Volume, and Logical Partitions Redundant Controller 10-5 10-6 Infortrend System Drive MappingPrimary and Secondary IDs Mapping Redundant Controller 10-7 10-8 Infortrend Fault-ToleranceWhat Is a Redundant Controller Configuration? How does Failover and Failback Work? Channel Bus Redundant Controller 10-9 10-10 Infortrend ID Mapping Status Normal OperationID Mapping Status Controller Failed Active-to-Active Configuration Controller Failover and FailbackReplacing a Failed Unit Auto-Failback Traffic Distribution and Failover Process Redundant Controller 10-12 Symptoms Controller FailureConnection 10-13 Infortrend Preparing Controllers RequirementsCabling Requirements Controller RCC cable Controller Settings Redundant Controller 10-15 Configurable Parameters LimitationsPrimary or Secondary 10-16 Infortrend Active-to-Standby Configuration Battery SupportCache Synchronization Redundant Controller 10-17 10-18 Infortrend Configuration Redundant Controller 10-19 Redundant Configuration Using Automatic Setting Enable Redundant ControllerAutoconfig Via Front Panel Keypad Redundant Controller 10-21 Redundant Configuration Using Manual SettingView and Edit Peripheral Dev RC connecting ENT to cancel Starting the Redundant ControllersCreating Primary and Secondary ID 10-22 Infortrend Set Sec. Ctlr Idna to ID 6? CHL=0 ID=0 Primary Ctlr Add ChannelView and Edit Logical Drives Redundant Controller 10-23 Mapping a Logical Drive/Logical Volume to the Host LUNs 10-24 Infortrend What will happen when one of the controllers fails? When and how is the failed controller replaced?Front Panel View of Controller Failure Redundant Ctlr Failure Detected Via Terminal Emulation 10-26 Infortrend Redundant Controller 10-27 10-28 Infortrend Assigning Logical Drives to the Secondary Controller Redundant Controller 10-29 10-30 Infortrend Redundant Controller 10-31 When and How Is the Failed Controller Replaced?Terminal Interface View of Controller Failure 10-32 Infortrend Forcing Controller Failover for Testing Redundant Controller 10-33 RCC Status Redundant Controller Communications Channel Secondary Controller RS-232Remote Redundant Controller Cache Synchronization on Write-Through Record of Settings 11-1 View and Edit Logical Drives 11-2 Infortrend View and Edit Logical Volumes Record of Settings 11-3 View and Edit Host LUN’s 11-4 Infortrend Record of Settings 11-5 View and Edit Scsi Drives 11-6 Infortrend Record of Settings 11-7 View and Edit Scsi Channels 11-8 Infortrend View and Edit Configuration ParametersCommunication Parameters Record of Settings 11-9 Host Side Scsi Parameters Disk Array Parameters 11-10 Infortrend Record of Settings 11-11 View and Edit Peripheral Devices 11-12 Infortrend Save Nvram to Disk, Restore from DiskRAID Security Password What is it and how does it work? Array Expansion Added Capacity Expand Logical Drive Re-Striping Array Expansion Mode 1 Expansion Adding Drives to a Logical Drive Add-Drive Procedure 12-5 12-6 Copy and Replace Procedure Expansion by Copy & Replace 12-8 Making Use of the Added Capacity Expand Logical Drive 12-9 12-10 Expand Logical Volume Limitations When Using Windows Example 12-13 12-14 12-15 12-16 12-17 Navigation Map Start Create View and Edit Scsi Drives View and Edit Scsi Channels View and Edit Configuration Parameters View and Edit Peripheral Device End Basic RAID Management Appendix Advanced Features Caching Operation 128 RAID Expansion Caching Optimization Fibre Channel Support A.R.T. Support Redundant Controller Data Safety System Security Environment Management User Interface Remote Manageability JBOD-Specific Others System Functions Upgrading Firmware Redundant Controller Rolling Firmware UpgradeUpgrading Firmware Redundant Controller Firmware Sync-version Establish the In-band Scsi connection in RAIDWatch Manager Upgrade Both Boot Record and Firmware Binaries Upgrading Firmware Using RS-232C Terminal Emulation Upgrade the Firmware Binary Only Upgrading Both Boot Record and Firmware Binaries Upgrading the Firmware Binary Only Event Messages Event IndexController Event Drive Scsi Channel/Drive Error Notification Logical Drive Event General Target Events I2C Device Notification SAF-TE Device 3fa2 Notice Controller FAN Back On-Line RPM Controller Event Happens? Happens? What to Do? Happens? What to Do? Drive Scsi Channel/Drive Error Received Sensekey Sensecode Happens? What to Do? Line LCD = I= Unexpected Sense Rec What to Do? What to Press ESC to clear the message Red Path for C Failure Detected Logical Drive Event Infortrend Happens? Infortrend Event Type General Target Events Controller On-board Event Type Check I 2C cable connection and contact your system supplier 3F22 Peripheral Device Alert high/low threshold Fan Speed Event Messages SES Device Line LCD . Temp Sensor Device Unknown Status What Happens? What to Line LCD . Current Sensor Device Not Supported Infortrend What Happens? Temperature back to non-critical level Controller Self Diagnostics Contlr FAN Back On-Line Happens? SES Device Alert Alert Notification What UPS device failure detected Index Index-1 Index-2 Infortrend Index-3 Index-4 Infortrend Nvram Index-5 RCC Index-6 Infortrend Index-7 Zmodem Index-8 Infortrend