Manuals / Compaq / Computer Equipment / Network Card

Compaq Infortrend Slot Number, Maximum Synchronous Transfer Clock, Maximum Transfer Width, 5-31

Models: Infortrend

1 347

Download 347 pages 43.22 Kb

Page 99

Image 99

Press ▼ or ▲ to select “View and Edit SCSI Target,” then press ENT.

Press ▼ or ▲ to select a SCSI target, then press ENT.

SCSI Target
CHL=1 ID=0	..

Slot Number

To set the Slot number of the SCSI target, choose “Slot Assignment," then press ENT. The current slot number will be displayed.

Press ▼ or ▲ to change the slot number, then press ENT for two seconds.

Slot Assignment Default No Set..

Slot Assignment

Set to

# 9 ?

Maximum Synchronous Transfer Clock

Press ▼ or ▲ to select a SCSI target, then press ENT.

To set the maximum synchronous clock of this SCSI target, choose “Max. Synchronous Xfer Clock," then press ENT. The current clock setting will be displayed on the LCD.

Press ▼ or ▲ to change the clock, then press ENT for two seconds.

SCSI Target
CHL=1 ID=0	..

Max Synchronous Xfer Clock# 12..

Period Factor Def= 12 to --?

Maximum Transfer Width

Press ▼ or ▲ to select a SCSI target, then press ENT.

SCSI Target
CHL=1 ID=0	..

To set the maximum transfer width of this SCSI target, choose “Max. Xfer Narrow Only” or “Max. Xfer Wide Supported,” then press ENT. The

Max Xfer Wide

Supported ..

5-31	Infortrend

Page 99

Image 99

Compaq Infortrend manual Slot Number, Maximum Synchronous Transfer Clock, Maximum Transfer Width, 5-31

Contents

Generic Operation Manual External RAID Controller & SubsystemRevision Firmware Version InfortrendTrademarks Product specifications are also subject to change without noticeCopyright This Edition First Published DisclaimerPrinted in Taiwan RMA PolicySupported Models Chapter 2 RAID Planning Table of ContentsChapter 3 Accessing the Array through Serial Port and Ethernet Chapter 1 RAID Functions An Introduction3.1.1 Chapter 4 LCD Screen MessagesChapter 5 LCD Keypad Operation Configuring RS-232C Connection via Front Panel5.13 Setting a SCSI Channel’s Primary ID - Drive ChannelSetting a SCSI Channel’s Secondary ID - Drive Channel 5.9 Viewing and Editing Logical Drives and Drive MembersChapter 7 Terminal Operation Chapter 6 Terminal Screen MessagesChapter 8 Fibre Operation viiiSetting a Secondary Controller’s SCSI ID - Drive Channel Chapter 9 Advanced Configuration 8.5 Multi-Host Access Control LUN Filtering9.2 Host-side and Drive-side SCSI Parameters Disk Array Parameters Chapter 10 Redundant ControllerMonitoring and Safety Mechanisms 10.3 ConfigurationChapter 12 Array Expansion Chapter 11 Record of SettingsAppendix D Event Messages Appendix A LCD Keypad Navigation MapAppendix B Firmware Functionality Appendix C System Functions Upgrading FirmwareOut-of-Band via Serial Port and Functional Table of ContentsChapter Functional Description5.6/7.6 Chapter Advanced ConfigurationsFibre Operation ChapterChapter Redundant Controller ConfigurationArray Expansion ChapterUpgrading Firmware Controller MaintenanceAppendix C xviiTable 8 List of TablesList of Figures xviiiFigure 2 - 1 Optimization Setting About This Manual Revision History Firmware Version & Other InformationVersion xxiiAn Introduction 1.2 Logical VolumeWhat is a logical volume? RAID Functions1.3 RAID Levels What are the RAID levels?Table 1 - 1 RAID Levels Figure 1 - 3 JBOD NRAIDJBOD Figure 1 - 2 NRAIDFigure 1 - 5 RAID RAIDRAID 0+1 Figure 1 - 4 RAIDRAID Figure 1 - 7 RAIDFigure 1 - 8 RAID RAIDFigure 1 - 10 Global Spare 1.4 Spare DrivesGlobal and Local Spare Drives Figure 1 - 9 Local Dedicated SpareLogical Drive Figure 1 - 12 Mixing Local and Global SparesFlash All but Selected Drives 1.5 Identifying DrivesFlash Selected SCSI Drive Flash All SCSI Drives1.6 Rebuild Automatic Rebuild and Manual Rebuild 1. Automatic RebuildFigure 1 - 13 Automatic Rebuild Figure 1 - 14 Manual Rebuild 2. Manual Rebuild3. Concurrent Rebuild in RAID 0+1 1.7 Logical Volume Multi-Level RAID Figure 1 - 15 Logical VolumeWhat is a logical volume? Figure 1 - 17 Logical Volume with 4 Logical Drives Figure 1 - 16 Logical Drive Composed of 24 DrivesConfiguration A - One logical drive with all 24 drives Figure 1 - 18 Logical Volume with Drives on Different Channels Spare drives assigned to a logical volume?Limitations Redundant Controller Different write policies within a logical volume?RAID expansion with logical volume? Different controller settings using logical volume?Multi-level RAID systems A logical volume with logical drives of different levels?2. How many drives on each drive channel? RAID Planning2.1 Considerations 1. How many physical drives do you have?5. Dual loop, hub, or switch? 3. How many drives would you like to appear to the host computer?4. What kind of host application? Figure 2 - 1 Optimization Setting Optimization Mode7. What RAID level? RAID Levels 8. Any spare drives?9. Limitations? Table 22.2 Configuring the Array Figure 2 - 2 Array Configuration Process2.2.1 Starting a RAID System 5. The next step is to make logical drives or storage partitions available through the host ports. When associated with a host ID or LUN number, each capacity volume appears as one system drive. The host SCSI or Fibre adapter will recognize the system drives after the host bus is re-initialized 2.3.2 Grouping Drives into an Array Figure 2 - 4 Connecting Drives2.3 Operation Theory 2.3.1 I/O Channel, SCSI ID, and LUNFigure 2 - 5 Physical locations of drive members Figure 2 - 6 Partitions in Logical Configurations2.3.3 Making Arrays Available to Hosts Figure 2 - 7 Mapping Partitions to Host ID/LUNsFigure 2 - 8 Mapping Partitions to LUNs under ID Controller Fault ManagementTable 2 - 2 Controller Parameter Settings 2.4 Tunable ParametersFibre Channel Parameters Optimization ModeSCSI Parameters Spin-Up ParametersOthers Array ConfigurationEthernet Accessing the ArrayThe following are guidelines on using the serial port through Serial Port and3.1.1 Configuring RS-232C Connection via Front Panel 3.1.2 Starting RS-232C Terminal Emulation The keys used when operating via the terminal are as followsWhat Is the “Disk Reserved Space?” 3.2 Out-of-Band via EthernetRAIDWatch and Reserved Space Availability Concern 3.2.1 Connecting Ethernet PortOther Concerns Requirements3.2.2 Configuring the Controller 1. Use a Terminal Emulator to Begin Configuration2. Create a Reserved Space on Drives 4. FTP Manager Programs to the Controller IP Address 3. Assign an IP Address to Ethernet Port5. Starting the Manager 3.2.3 NPC Onboard 3-10 The SNMPTRAP sectionThe EMAIL section The BROADCAST section4.1 The Initial Screen 4.2 Quick Installation ScreenStatus/Data Transfer Indicator LCD Screen MessagesRAID level 4.3 Logical Drive StatusLG0 RAID5 DRV=3 LG=0 RAID5 DRV=3 2021MB GD SB=1 2021MB GD SB=1 Logical Drive4.4 Logical Volume Status Logical Volume StatusLV=0 ID=09816DE9 00002021MB DRV=1 Drive Status 4.5 SCSI Drive StatusC=1 I=0 1010MB LG=0 LN SEAGATEPID = Default SCSI Bus Sync Clock4.6 SCSI Channel Status CH0=Host4.7 Controller Voltage and Temperature 4.9 View and Edit Event Logs 4.8 Cache Dirty PercentageOptimization Modes 5.1 Power on RAID EnclosureLCD Keypad Operation 5.2 Caching ParametersOptimization Mode and Stripe Size Database and Transaction-based ApplicationsVideo Recording/Playback and Imaging Applications Optimization for Random or Sequential I/O Write-Back/Write-Through Cache Enable/DisableWrite-Back Cache Enabled Disable WriteEvery time you change the Caching Parameters, you must reset the controller for the changes to take effect View Drive Information 5.3 View Connected DrivesView and Edit SCSI Drives C=2 I=0 1010MB New DRV SEAGATELogical Drive Preferences 5.4 Creating a Logical DriveChoosing a RAID Level Choosing Member DrivesWrite Policy Maximum Drive CapacitySpare Drive Assignments Disk Reserved SpaceStripe Size Beginning InitializationThe On-Line Mode The Off-Line Mode Initializing090% Please Wait LG=0 Initializat Ion CompletedLG=0 RAID5 DRV=3 2012MB GD SB=0 5.5 Creating a Logical Volume Initialization ModeWrite Policy Logical Volume Assignment LV=0 Part=0 700MB ? LV=0 Partition=1 1321MB ? 5.6 Partitioning a Logical Drive/Logical VolumeView and Edit Logical Volume LV=0 ID=685AE502 2021MB DRV=1 Partition Logical Volume LV=0 Part=0 2021MB ? LV=0 Part=0 2021MB5.7 Mapping a Logical Volume/Logical Drive to Host LUN Adding a Local Spare Drive 5.8 Assigning Spare Drive and Rebuild SettingsInfortrend Rebuild SettingsAdding a Global Spare Drive 5-15Deleting a Logical Drive 5.9 Viewing and Editing Logical Drives and Drive MembersFigure 5 - 1 Drive Space Allocated to the Last Partition Deleting a Partition of a Logical Drive5-18 Assigning a Name to a Logical DriveRebuilding a Logical Drive Front Panel OperationRegenerating Logical Drive Parity Media Scan Write Policy 5-21Infortrend Pass-through SCSI Commands 5.10 Viewing and Editing Host LUNsViewing and Deleting LUN Mappings Scanning New SCSI Drive 5.11 Viewing and Editing SCSI DrivesIdentifying a Drive Front Panel Operation5-24 5.12 Viewing and Editing SCSI Channels Deleting Spare Drive Global / Local Spare DriveRedefining Channel Mode Setting a SCSI Channel’s ID - Host Channel Viewing IDsAdding a Channel ID Deleting a Channel ID Setting a SCSI Channel’s Primary ID - Drive Channel5-28 Setting a SCSI Channel’s Secondary ID - Drive ChannelSetting Channel Bus Terminator Front Panel OperationSetting Transfer Speed Viewing and Editing SCSI Target - Drive Channel Setting Transfer Width5-31 Slot NumberMaximum Synchronous Transfer Clock Maximum Transfer WidthFront Panel Operation Disconnecting SupportParity Check Maximum Tag CountCHL=1 ID=0 Restore to Default SettingRestore to Default Setting Restore to Default Setting? SCSI TargetMute Beeper Change PasswordChanging Password 5.13 System FunctionsRe-Ent Password Disabling PasswordReset Controller Old PasswordFront Panel Operation Restore NVRAM from DisksSaving NVRAM to Disks Controller MaintenanceLCD Title Display Controller Name Password Validation Timeout5.14 Controller Parameters Controller NameTime Zone Controller Date and TimeMMDDhhmmYYYY Date and TimeGMT +0800 Date and TimeSCSI Drive Low-level Format 5.15 SCSI Drive UtilitiesSCSI Drive Read/Write Test Cursor Bar Transfer Rate IndicatorTerminal Screen Messages 6.1 The Initial Screen6.2 Main Menu 6.3 Quick InstallationTerminal Screen Messages SizeMB 6.4 Logical Drive StatusRAID SIZE MBSizeMB 6.5 Logical Volume StatusColumn C NameSpeed 6.6 SCSI Drive StatusSlot Size MBMode 6.7 SCSI Channel’s StatusThe default setting of the channel is ??.? MHz in The default setting of the channel is Asynchronous mode??.?M TermCurSynClk CurWidController voltage and temperature monitoring 6.8 Controller Voltage and TemperatureENTER 6.9 Viewing Event Logs on the ScreenChapter 7.1 Power on RAID EnclosureTerminal Operation 7.2 Caching ParametersLimitations Database and Transaction-based ApplicationsVideo Recording/Playback and Imaging Applications Terminal Operation Write-Back/Write-Through Cache Enable/DisableOptimization Mode and Stripe Size Optimization for Random or Sequential I/O7.3 Viewing the Connected Drives 7.4 Creating a Logical Drive Logical Drive Preferences A pull-down list of supported RAID levels will appear. In this chapter, RAID 5 will be used to demonstrate the configuration process. Choose a RAID level for this logical driveChoosing a RAID Level Choosing Member DrivesDisk Reserved Space Assign Spare DrivesLogical Drive Assignments You can add a spare drive from the list of the unused drives. The spare chosen here is a Local spare and will automatically replace any failed drive in the event of drive failure. The controller will then rebuild data onto the replacement drivePress ESC to continue when all the preferences have been set Initialization ModeStripe Size Use the ESC key to view the status of the created logical drive 7.5 Creating a Logical Volume 7.6 Partitioning a Logical Drive/Logical Volume Choose the logical volume you wish to partition, then press ENTER. Choose “Partition logical volume”, then press ENTER. Select from the list of undefined partitions and Press ENTER 7.7 Mapping a Logical Volume to Host LUN 4. When prompted to “Map Host LUN, press ENTER Adding Local Spare Drive 7.8 Assigning Spare Drive, Rebuild SettingsAdding a Global Spare Drive 7.9 Viewing and Editing Logical Drive and Drive MembersAssigning a Name to a Logical Drive Figure 7 - 1 Drive Space Allocated to the Last PartitionDeleting a Logical Drive Deleting a Partition of a Logical DriveRebuilding a Logical Drive 7-18Infortrend When rebuild has already started, choose “Rebuild progress” to see the rebuilding progress Regenerating Logical Drive ParityMedia Scan Write Policy 2. Iteration CountPass-through SCSI Commands 7.10 Viewing and Editing Host LUNsViewing or Deleting LUN Mappings Edit Host-ID/WWN Name ListScanning New Drive 7.11 Viewing and Editing SCSI DrivesDeleting Spare Drive Global / Local Spare Drive Slot Number Drive EntryIdentifying Drive These two functions are reserved for Fault Bus configurationPage Redefining Channel Mode 7.12 Viewing and Editing SCSI ChannelsViewing and Editing SCSI IDs - Host Channel Viewing and Editing SCSI IDsAdding a SCSI ID Primary/Secondary Controller ID Deleting an ID Setting a Primary Controller’s SCSI ID - Drive ChannelDrive Channel Setting a Secondary Controller’s SCSI ID - Drive ChannelSetting Channel Terminator Setting a Transfer SpeedHost Channel Setting the Transfer WidthViewing and Editing SCSI Target / Drive Channel This setting is reserved for the Fault-Bus optionSlot Number Choose “Maximum Sync. Xfer Clock,” then press ENTER. A dialog box will appear on the screen. Enter the clock, then press ENTER Maximum Synchronous Transfer ClockMaximum Transfer Width Parity CheckMaximum Tag Count Data RateDisconnecting Support Choose “Disconnect Support.” Choose Yes in the dialog box that follows to confirm the settingshould work fine with most drives. Changing this setting is not recommended unless some particular bus signal issues occur 7.13 System Functions Change PasswordMute Beeper Setting a New Password Changing the PasswordShutdown Controller Disabling the PasswordReset Controller The new password will now become the controller’s password. Providing the correct password is necessary when entering the main menu from the initial screen7.14 Controller Parameters Controller NameLCD Title Display Controller Name 7-38 Restore NVRAM from DisksSaving NVRAM to Disks Terminal OperationPassword Validation Timeout Controller Unique IdentifierPress Yes to confirm 7-40 Terminal Operation7-41 Set Controller Date and TimeTime Zone Date and Time7.15 Drive Information SCSI Drive UtilitiesView Drive Information SCSI Drive Low-level Format Do not switch the controller’s and/or SCSI disk drive’s power off during the SCSI Drive Low-level Format. If any power failure occurs during the formatting process, the formatting must be performed again when power resumesSCSI Drive Read/Write Test Terminal Operation7-44 Fibre Operation 8.1 OverviewChapter Channel Mode Assignment 8.2 Major ConcernsRedundant Cache Coherency Channels RCC Connection between ControllersFibre Operation performance1Gbit Fibre Channel 8.3 Supported FeaturesFibre Chip Multiple Target IDsIn-band Fibre and S.E.S. Support Drive IDs8.4 Configuration Host and Drive Parameters Channel ModePrimary and Secondary Controller IDs Redundant Controller Cache Coherency Channel RCC Channel View Channel WWNLimitation View Device Port Name List WWPN View and Edit Fibre DriveUser-Assigned ID Scan SCSI Drive View and Edit Host-Side Parameters A drive enclosure usually has drive slots pre-assigned with specific IDs. There are occasions when an ID needs to be assigned manually to a device other than an ID provided otherwise. The set slot number and the add drive entry functions are reserved for Infortrends Fault-bus operationView Drive Information View and Edit Drive-Side Parameters 2. Drive-Side Dual Loop 1. Fibre Channel Connection TypeController firmware automatically examines the node names and port names of all the connected drives once initiated. If devices on two different drive channels appear with the same loop ID and port name, controller will consider these two drive channels as a dual loop Controller Unique IdentifierController Communications over Fibre Loops 2. Communications Traffic Distributed over All Drive Loops Select all drive loops and configure them as Drive + RCCOM Drive Loops plus Redundant Controller Communications. The communications traffic between the two controllers will be automatically distributed over all drive loops Figure 8 - 1 Storage Pool 8.5 Multi-Host Access Control LUN FilteringCreating LUN Masks Figure 8 - 2 Host-LUN MappingFigure 8 - 3 LUN Mask WWN Name List Logical Unit to Host LUN Mapping Choose Yes to proceed Filter Type Include or Exclude LUN Mask ID Range ConfigurationSample Configuration Access Mode Read Only or Read/WriteFigure 8 - 4 LUN Filtering - Configuration Sample Configuration Procedure Entry 3 LD1-P0, ID=0x…F111, Mask=0x…FFFE, Filter Type = Include, Access Mode = Read Only. It means P0 of LD1 is Read Only for Host A and B Chapter Advanced Configurations9.1 Fault Prevention S.M.A.R.TReplace after Clone 9.1.1 Clone Failing DrivePerpetual Clone The cloning process will begin with a notification message A. Introduction B. Infortrends Implementations with S.M.A.R.T9.1.2 S.M.A.R.T. Self-Monitoring, Analysis and Reporting Technology Clone + Replace DisableDetect Only Perpetual CloneConfiguration Procedure Enabling the S.M.A.R.T. FeatureExamining Whether Your Drives Support S.M.A.R.T Using S.M.A.R.T. Functions 3b. Whenever a drive predicts symptoms of predictable drive failure, controller will issue an error message original role - it will become a spare drive again and start rebuilding the failed drive 9-10Maximum Concurrent Host LUN Connection “Nexus” in SCSI 9.2 Host-side and Drive-side SCSI Parameters9.2.1 Host-side SCSI Parameters Foreword SCSI Channel, SCSI ID and LUN9-12 Number of Tags Reserved for each Host-LUN Connection9-13 Maximum Queued I/O CountLUNs per Host SCSI ID LUN Applicability9-14 What is In-band?Peripheral Device Type In-band SCSI or FibreTable 9 - 1 Peripheral Device Type Parameters Peripheral Device Type Parameters for Various Operating SystemsCapacity Table 9 - 2 Peripheral Device Type SettingsCylinder/Head/Sector Mapping Table 9 - 3 Cylinder/Head/Sector Mapping under Sun SolarisSelecting Sector Ranges Selecting Head Ranges Selecting Cylinder RangesConfiguring Sector Ranges/Head Ranges/Cylinder Ranges 9.2.2 Drive-side Parameters SCSI Motor Spin-Up9-18 SCSI Reset at Power-Up Disk Access Delay Time SCSI I/O Timeout9-20 Maximum Tag Count Tag Command Queuing 9-22 Detection of Drive Hot Swap Followed by Auto RebuildSAF-TE and S.E.S. Enclosure Monitoring Periodic Drive Check TimeIdle Drive Failure Detection By choosing a time value to enable the Periodic Drive Check Time,” the controller will poll all connected drives through the controller’s drive channels at the assigned interval. Drive removal will be detected even if a host does not attempt to access data on the drive 9-249-25 9.3 Monitoring and Safety MechanismsDynamic Switch Write-Policy View Peripheral Device Status9-26 Controller Auto-Shutdown - Event Trigger OptionRebuild Priority 9.4 Disk Array Parameters9-28 Verification on WritesRedundant Controller 10.1 Operation TheoryChapter 10.1.2 Considerations Related to Physical Connection 10.1.1 Setup FlowchartFigure 10 - 1 Redundant Controller Configuration Flowchart Figure 10 - 1 Dual-Controller Using SCSI-Based ControllersFibre-Based Controllers 10.1.3 Grouping Hard Drives and LUN Mapping 1. Dedicated Communications Loops - “RCC”2. Communications over Drive Loops - “Drive + RCC” Logical Drive, Logical Volume, and Logical Partitions Primary and Secondary IDs System Drive MappingFigure 10 - 3 Grouping Hard Drives Figure 10 - 4 Partitioning of Logical UnitsFigure 10 - 5 Mapping System Drives Mapping LUNs Mapping10.1.4 Fault-Tolerance What Is a Redundant Controller Configuration?Figure 10 - 6 Mapping System Drives IDs Figure 10 - 7 Redundant Controller Channel Bus How does Failover and Failback Work? A. Channel Buschannel 0 - Failed Table 10 - 1 ID Mapping Status Normal OperationTable 10 - 2 ID Mapping Status Controller Failed Figure 10 - 8 Controller FailoverAuto-Failback C. Active-to-Active ConfigurationB. Controller Failover and Failback Replacing a Failed UnitFigure 10 - 9 Traffic Distribution D. Traffic Distribution and Failover ProcessConnection SymptomsE. Controller Failure Figure 10 - 10 Controller FailoverCabling Requirements Out-of-Band Configuration10.2 Preparing Controllers 10.2.1 Requirements3. Create Primary and Secondary IDs on Drive Channels Controller Settings1. Enable Redundant Controller 2. Controller Unique Identifier10.2.3 Configurable Parameters 10.2.2 LimitationsPrimary or Secondary Cache Synchronization Active-to-Active ConfigurationActive-to-Standby Configuration Battery SupportInfortrend 10-1810.3 Configuration 10.3.1 Via Front Panel Keypad Redundant Configuration Using Automatic Setting1. Enable Redundant Controller AutoconfigRedundant Configuration Using Manual Setting 1. Enable Redundant Controller2. Controller Unique ID Starting the Redundant Controllers Creating Primary and Secondary IDDrive Channel Host Channel Assigning a Logical Drive/Logical Volume to the Secondary ControllerMapping a Logical Drive/Logical Volume to the Host LUNs Front Panel View of Controller Failure What will happen when one of the controllers fails?When and how is the failed controller replaced? The replacement controller has to be pre-configured as the SecondaryRedundant Configuration Using Automatic Setting 10.3.2 Via Terminal EmulationRedundant Configuration Using Manual Setting Redundant Controller10-27 Infortrend 10-28Assigning Logical Drives to the Secondary Controller Creating Primary and Secondary IDDrive Channel Host Channel Mapping a Logical Drive/Logical Volume to the Host LUNs Choose “host channel-ID” Choose mapping to which “logical unit”Select LUN number Select partition Mapping optioin Confirming mapping scheme10.3.3 When and How Is the Failed Controller Replaced? Terminal Interface View of Controller FailureWhat will happen when one of the controllers fails? When the scanning has completed, the status will change to Enabled Forcing Controller Failover for Testing 1. Pulling out one of the controllers to simulate controller failure2. Failover by Forcing controller failure Cache Synchronization on Write-Through RCC Status Redundant Controller Communications ChannelSecondary Controller RS-232 Remote Redundant ControllerRecord of Settings 11.1 View and Edit Logical DrivesChapter Partition Information 11-2Infortrend 11.2 View and Edit Logical Volumes Record of Settings11-3 Host-ID/WWN Name List 11.3 View and Edit Host LUN’sAccess Restriction Setting LUN MappingsAccess Host Filter EntriesLV/LD Local Spare? 11.4 View and Edit SCSI Drives11.5 View and Edit SCSI Channels Record of Settings11-7 Communication Parameters 11.6 View and Edit Configuration ParametersEthernet Configuration PPP ConfigurationDrive Side SCSI Parameters Record of SettingsCaching Parameters Host Side SCSI Parameterson write-through Disk Array ParametersRedundant Controller Parameters Cache synchronizationView System Information 11.7 View and Edit Peripheral DevicesDefine Peripheral Device Active Signal Set Peripheral Device Entry11.8 Save NVRAM to Disk, Restore from Disk 11.9 RAID Security PasswordRAID Security 12-1 What is it and how does it work?Array Expansion 12.1 Overview3. Applicable Arrays Note on Expansion1. Added Capacity 2. Size of the New DriveExpand Logical Drive Re-Striping Figure 12 - 1 Logical Drive Expansion12-3 Add-Drive Procedure 12.2 Mode 1 Expansion Adding Drives to a Logical DriveFigure 12 - 2 Expansion by Adding Drive Press ESC to proceed and the notification will prompt 12-5Upon completion, there will appear a confirming notification. The capacity of the added drive will appear as an unused partition Figure 12 - 3 Expansion by Copy & Replace Copy and Replace Procedure12.3 Mode 2 Expansion Copy and Replace Drives with Drives of Larger CapacityChoose Yes to confirm and proceed Press ESC to view the progress 12-9 12.4 Making Use of the Added Capacity Expand Logical DriveThe total capacity of logical drive has been expanded to 6 Gigabytes Choose Yes to confirm and proceedUpon completion, you will be prompted by the notification message Press ESC to return to the previous menu screen12-11 12.5 Expand Logical Volume12.6 Configuration Example Volume Extension in Windows 2000 Server Limitations When Using WindowsExample You can view information about this drive in the Windows 2000 Server’s Computer Management - Storage - Disk Management 12-13Follow the steps described in the previous section to add or copy & replace SCSI disk drives and perform Logical Drive Expansion Return to Windows 2000 Server’s Disk Management. There now exists a Disk 2 with 8.3GB of free space. You may use the “rescan disks” command to bring up the new drive 12-15The Extend Volume Wizard should guide you through the rest of the process 12-17 Drive E now has a capacity of about 25GBArray Expansion Create InstallSelect a configured LCD Keypad NavigationView and Edit Logical VolumeLogical Volume Reset ControllerView and Edit SCSI Drives Navigation Map A-3Select a Host or Drive Channel A-4 InfortrendView and Edit SCSI ChannelsNavigation Map A-5 View and Edit Configuration ParametersView and Edit Peripheral Device View and Edit Configuration ParametersController Password set RS232 Enabled/DisabledView and Edit System FunctionsView System InformationFirmware Functionality Specifications Basic RAID ManagementAppendix Advanced Features RAID0 Caching OperationCache buffer sorting prior to cache flush operation RAID ExpansionFibre Channel Support Redundant Controller S.M.A.R.T. SupportData Safety System Security Environment Management Remote Manageability User InterfaceOthers JBOD-SpecificUpgrading Firmware New Features Supported with FirmwareRedundant Controller Rolling Firmware Upgrade System Functions Upgrading FirmwareUpgrading Firmware Using In-band SCSI + RAIDWatch Manager Redundant Controller Firmware Sync-versionEstablish the In-band SCSI connection in RAIDWatch Manager Upgrade Both Boot Record and Firmware Binaries Upgrade the Firmware Binary Only Upgrading Firmware Using RS-232C Terminal EmulationEstablishing the connection for the RS-232C Terminal Emulation Upgrading Both Boot Record and Firmware BinariesInfortrend Upgrading the Firmware Binary OnlyAlert Event MessagesEvent Index Controller EventChannel Drive SCSI Channel/Drive ErrorNotification DriveController on-board Logical Drive EventGeneral Target Events Alert SAF-TE DeviceSES Devices I2C DeviceNotification SAF-TE Device Infortrend I2C DeviceController Event AlertEvent Messages What to Do? Event TypeWhat to Do? Event TypeEvent Messages Happens? What to Do?Event Type Happens? What to Do?Infortrend Drive SCSI Channel/Drive ErrorDrive D-10Received Sensekey Sensecode Event MessagesD-11 D-12 SensecodeBlocknumber Sensekey Sensecode Sensekey SensecodeD-13 Event MessagesEvent Type Event TypeEvent Type What to Do?Channel Event MessagesD-15 Notification D-16Infortrend D-17 Logical Drive EventAlert Event MessagesNotification D-18Infortrend Event TypeD-19 Event MessagesInfortrend D-20D-21 Event TypeHappens? Event MessagesInfortrend General Target EventsAlert SAF-TE Device D-22Controller On-board Event MessagesD-23 D-24 Event TypeEvent Type Event TypeI2C Device Event MessagesD-25 Infortrend D-26D-27 Event MessagesSES Device D-28Infortrend 2-Line LCD . Temp Sensor Device Unknown Status Event MessagesD-29 Infortrend D-302-Line LCD . Current Sensor Device Not Supported Event MessagesD-31 Infortrend D-32General Peripheral Device Event MessagesD-33 Notification SAF-TE Device D-34Infortrend Controller Self Diagnostics Event MessagesD-35 I2C Device D-36Infortrend Happens? Happens?Happens? Happens?SES Device Alert D-38Infortrend General Peripheral Device Event MessagesD-39 Index Infortrend Index-2Index-3 Infortrend Index-4Index-5 Infortrend Index-6Index-7 Infortrend Index-8