Manuals / Compaq / Computer Equipment / Network Card

Compaq Infortrend manual I2C Device, SES Devices

Models: Infortrend

1 347

Download 347 pages 43.22 Kb

Page 304

Temperature Detected (_._C )

[3f22] Peripheral Device ALERT: Controller FAN _ Not Present or Failure Detected

[3f22] Peripheral Device ALERT: Controller FAN _ <high/low threshold> Speed Detected (_RPM)

[3f21] Peripheral Device ALERT: +3.3V <upper/lower threshold> Voltage Detected (_)

[3f21] Peripheral Device ALERT: +5V <upper/lower threshold> Voltage Detected (_)

[3f21] Peripheral Device ALERT: +12V <upper/lower threshold> Voltage Detected (_)

I2C Device:

[3f23] Peripheral Device ALERT: Temperature Sensor _ Failure Detected

[3f23] Peripheral Device ALERT: Temperature Sensor _ Not Present

[3f23] Peripheral Device ALERT: <high/low threshold> Temperature _ Detected (_(F/C))

[3f22] Peripheral Device ALERT: FAN _ Failure Detected

[3f22] Peripheral Device ALERT: FAN _ Not Present

[3f22] Peripheral Device ALERT: <high/low threshold> FAN _ Speed Detected (_ RPM)

[3f21] Peripheral Device ALERT: Power Supply _ Failure Detected

[3f21] Peripheral Device ALERT: Power Supply _ Not Present

[3f21] Peripheral Device ALERT: <high/low threshold> Power Supply _ Voltage Detected (_)

[3f24] Peripheral Device ALERT: UPS _ AC Power Failure Detected

[3f24] Peripheral Device ALERT: UPS _ Battery Failure Detected

SES Devices:

[3f21] SES (C_ I_) Power Supply _: <Vendor descriptor strings/Device Not Supported>!

[3f21] SES (C_ I_) Power Supply _: <Vendor descriptor strings/Device Not Installed>!

[3f21] SES (C_ I_) Power Supply _: <Vendor descriptor strings/Device Unknown Status>!

[3f21] SES (C_ I_) Power Supply _: <Vendor descriptor strings/Device Not Available>!

[3f22] SES (C_ I_) Cooling element _: <Vendor descriptor strings/Device Not Supported>!

[3f22] SES (C_ I_) Cooling element _: <Vendor descriptor strings/Device Not installed>!

[3f22] SES (C_ I_) Cooling element _: <Vendor descriptor strings/Device Unknown Status>!

[3f22] SES (C_ I_) Cooling element _: <Vendor descriptor strings/Device Not Available>!

[3f23] SES (C_ I_) Temperature Sensor _: <Vendor descriptor strings/Device Not Supported>!

[3f23] SES (C_ I_) Temperature Sensor _: <Vendor descriptor strings/Device Not installed>!

[3f23] SES (C_ I_) Temperature Sensor _: <Vendor descriptor strings/Device

D-4	Infortrend

Image 304

Compaq Infortrend manual I2C Device, SES Devices

Contents

External RAID Controller & Subsystem Revision Firmware VersionInfortrend Generic Operation ManualProduct specifications are also subject to change without notice Copyright This Edition First PublishedDisclaimer TrademarksRMA Policy Printed in TaiwanSupported Models Table of Contents Chapter 3 Accessing the Array through Serial Port and EthernetChapter 1 RAID Functions An Introduction Chapter 2 RAID PlanningChapter 4 LCD Screen Messages Chapter 5 LCD Keypad OperationConfiguring RS-232C Connection via Front Panel 3.1.1Setting a SCSI Channel’s Primary ID - Drive Channel Setting a SCSI Channel’s Secondary ID - Drive Channel5.9 Viewing and Editing Logical Drives and Drive Members 5.13Chapter 6 Terminal Screen Messages Chapter 7 Terminal Operationviii Chapter 8 Fibre OperationSetting a Secondary Controller’s SCSI ID - Drive Channel 8.5 Multi-Host Access Control LUN Filtering Chapter 9 Advanced Configuration9.2 Host-side and Drive-side SCSI Parameters Chapter 10 Redundant Controller Monitoring and Safety Mechanisms10.3 Configuration Disk Array ParametersChapter 11 Record of Settings Chapter 12 Array ExpansionAppendix A LCD Keypad Navigation Map Appendix B Firmware FunctionalityAppendix C System Functions Upgrading Firmware Appendix D Event MessagesFunctional Table of Contents ChapterFunctional Description Out-of-Band via Serial Port and5.6/7.6 Advanced Configurations Fibre OperationChapter ChapterRedundant Controller Configuration Array ExpansionChapter ChapterController Maintenance Appendix Cxvii Upgrading FirmwareList of Tables List of Figuresxviii Table 8Figure 2 - 1 Optimization Setting About This Manual Firmware Version & Other Information Revision Historyxxii Version1.2 Logical Volume What is a logical volume?RAID Functions An IntroductionWhat are the RAID levels? 1.3 RAID LevelsTable 1 - 1 RAID Levels NRAID JBODFigure 1 - 2 NRAID Figure 1 - 3 JBODRAID RAID 0+1Figure 1 - 4 RAID Figure 1 - 5 RAIDFigure 1 - 7 RAID Figure 1 - 8 RAIDRAID RAID1.4 Spare Drives Global and Local Spare DrivesFigure 1 - 9 Local Dedicated Spare Figure 1 - 10 Global SpareFigure 1 - 12 Mixing Local and Global Spares Logical Drive1.5 Identifying Drives Flash Selected SCSI DriveFlash All SCSI Drives Flash All but Selected DrivesAutomatic Rebuild and Manual Rebuild 1. Automatic Rebuild 1.6 RebuildFigure 1 - 13 Automatic Rebuild 2. Manual Rebuild Figure 1 - 14 Manual Rebuild3. Concurrent Rebuild in RAID 0+1 Figure 1 - 15 Logical Volume 1.7 Logical Volume Multi-Level RAIDWhat is a logical volume? Figure 1 - 16 Logical Drive Composed of 24 Drives Figure 1 - 17 Logical Volume with 4 Logical DrivesConfiguration A - One logical drive with all 24 drives Spare drives assigned to a logical volume? Figure 1 - 18 Logical Volume with Drives on Different ChannelsLimitations Different write policies within a logical volume? RAID expansion with logical volume?Different controller settings using logical volume? Redundant ControllerA logical volume with logical drives of different levels? Multi-level RAID systemsRAID Planning 2.1 Considerations1. How many physical drives do you have? 2. How many drives on each drive channel?3. How many drives would you like to appear to the host computer? 5. Dual loop, hub, or switch?4. What kind of host application? Optimization Mode Figure 2 - 1 Optimization Setting7. What RAID level? 8. Any spare drives? 9. Limitations?Table 2 RAID LevelsFigure 2 - 2 Array Configuration Process 2.2 Configuring the Array2.2.1 Starting a RAID System 5. The next step is to make logical drives or storage partitions available through the host ports. When associated with a host ID or LUN number, each capacity volume appears as one system drive. The host SCSI or Fibre adapter will recognize the system drives after the host bus is re-initialized Figure 2 - 4 Connecting Drives 2.3 Operation Theory2.3.1 I/O Channel, SCSI ID, and LUN 2.3.2 Grouping Drives into an ArrayFigure 2 - 6 Partitions in Logical Configurations Figure 2 - 5 Physical locations of drive membersFigure 2 - 7 Mapping Partitions to Host ID/LUNs 2.3.3 Making Arrays Available to HostsFigure 2 - 8 Mapping Partitions to LUNs under ID Fault Management Table 2 - 2 Controller Parameter Settings2.4 Tunable Parameters ControllerOptimization Mode SCSI ParametersSpin-Up Parameters Fibre Channel ParametersArray Configuration OthersAccessing the Array The following are guidelines on using the serial portthrough Serial Port and Ethernet3.1.1 Configuring RS-232C Connection via Front Panel The keys used when operating via the terminal are as follows 3.1.2 Starting RS-232C Terminal Emulation3.2 Out-of-Band via Ethernet What Is the “Disk Reserved Space?”RAIDWatch and Reserved Space 3.2.1 Connecting Ethernet Port Other ConcernsRequirements Availability Concern1. Use a Terminal Emulator to Begin Configuration 3.2.2 Configuring the Controller2. Create a Reserved Space on Drives 3. Assign an IP Address to Ethernet Port 4. FTP Manager Programs to the Controller IP Address5. Starting the Manager 3.2.3 NPC Onboard The SNMPTRAP section The EMAIL sectionThe BROADCAST section 3-104.2 Quick Installation Screen Status/Data Transfer IndicatorLCD Screen Messages 4.1 The Initial Screen4.3 Logical Drive Status LG0 RAID5 DRV=3 LG=0 RAID5 DRV=3 2021MB GD SB=1 2021MB GD SB=1Logical Drive RAID levelLogical Volume Status 4.4 Logical Volume StatusLV=0 ID=09816DE9 00002021MB DRV=1 4.5 SCSI Drive Status C=1 I=0 1010MBLG=0 LN SEAGATE Drive StatusDefault SCSI Bus Sync Clock 4.6 SCSI Channel StatusCH0=Host PID =4.7 Controller Voltage and Temperature 4.8 Cache Dirty Percentage 4.9 View and Edit Event Logs5.1 Power on RAID Enclosure LCD Keypad Operation5.2 Caching Parameters Optimization ModesDatabase and Transaction-based Applications Optimization Mode and Stripe SizeVideo Recording/Playback and Imaging Applications Write-Back/Write-Through Cache Enable/Disable Write-Back Cache EnabledDisable Write Optimization for Random or Sequential I/OEvery time you change the Caching Parameters, you must reset the controller for the changes to take effect 5.3 View Connected Drives View and Edit SCSI DrivesC=2 I=0 1010MB New DRV SEAGATE View Drive Information5.4 Creating a Logical Drive Choosing a RAID LevelChoosing Member Drives Logical Drive PreferencesMaximum Drive Capacity Spare Drive AssignmentsDisk Reserved Space Write PolicyBeginning Initialization Stripe SizeThe On-Line Mode Initializing090% Please Wait LG=0 Initializat Ion Completed The Off-Line ModeLG=0 RAID5 DRV=3 2012MB GD SB=0 Initialization Mode 5.5 Creating a Logical VolumeWrite Policy Logical Volume Assignment 5.6 Partitioning a Logical Drive/Logical Volume View and Edit Logical Volume LV=0 ID=685AE502 2021MB DRV=1Partition Logical Volume LV=0 Part=0 2021MB ? LV=0 Part=0 2021MB LV=0 Part=0 700MB ? LV=0 Partition=1 1321MB ?5.7 Mapping a Logical Volume/Logical Drive to Host LUN 5.8 Assigning Spare Drive and Rebuild Settings Adding a Local Spare DriveRebuild Settings Adding a Global Spare Drive5-15 Infortrend5.9 Viewing and Editing Logical Drives and Drive Members Deleting a Logical DriveDeleting a Partition of a Logical Drive Figure 5 - 1 Drive Space Allocated to the Last PartitionAssigning a Name to a Logical Drive Rebuilding a Logical DriveFront Panel Operation 5-18Regenerating Logical Drive Parity Media Scan 5-21 Write PolicyInfortrend 5.10 Viewing and Editing Host LUNs Pass-through SCSI CommandsViewing and Deleting LUN Mappings 5.11 Viewing and Editing SCSI Drives Scanning New SCSI DriveFront Panel Operation Identifying a Drive5-24 Deleting Spare Drive Global / Local Spare Drive 5.12 Viewing and Editing SCSI ChannelsRedefining Channel Mode Viewing IDs Setting a SCSI Channel’s ID - Host ChannelAdding a Channel ID Setting a SCSI Channel’s Primary ID - Drive Channel Deleting a Channel IDSetting a SCSI Channel’s Secondary ID - Drive Channel Setting Channel Bus TerminatorFront Panel Operation 5-28Setting Transfer Speed Setting Transfer Width Viewing and Editing SCSI Target - Drive ChannelSlot Number Maximum Synchronous Transfer ClockMaximum Transfer Width 5-31Disconnecting Support Parity CheckMaximum Tag Count Front Panel OperationRestore to Default Setting Restore to Default Setting Restore to Default Setting?SCSI Target CHL=1 ID=0Change Password Changing Password5.13 System Functions Mute BeeperDisabling Password Reset ControllerOld Password Re-Ent PasswordRestore NVRAM from Disks Saving NVRAM to DisksController Maintenance Front Panel OperationPassword Validation Timeout 5.14 Controller ParametersController Name LCD Title Display Controller NameController Date and Time Time ZoneDate and Time GMT +0800Date and Time MMDDhhmmYYYY5.15 SCSI Drive Utilities SCSI Drive Low-level FormatSCSI Drive Read/Write Test Transfer Rate Indicator Terminal Screen Messages6.1 The Initial Screen Cursor Bar6.3 Quick Installation 6.2 Main MenuTerminal Screen Messages 6.4 Logical Drive Status RAIDSIZE MB SizeMB6.5 Logical Volume Status Column CName SizeMB6.6 SCSI Drive Status SlotSize MB Speed6.7 SCSI Channel’s Status The default setting of the channel is ??.? MHz inThe default setting of the channel is Asynchronous mode ModeTerm CurSynClkCurWid ??.?M6.8 Controller Voltage and Temperature Controller voltage and temperature monitoring6.9 Viewing Event Logs on the Screen ENTER7.1 Power on RAID Enclosure Terminal Operation7.2 Caching Parameters ChapterDatabase and Transaction-based Applications LimitationsVideo Recording/Playback and Imaging Applications Write-Back/Write-Through Cache Enable/Disable Optimization Mode and Stripe SizeOptimization for Random or Sequential I/O Terminal Operation7.3 Viewing the Connected Drives 7.4 Creating a Logical Drive A pull-down list of supported RAID levels will appear. In this chapter, RAID 5 will be used to demonstrate the configuration process. Choose a RAID level for this logical drive Choosing a RAID LevelChoosing Member Drives Logical Drive PreferencesAssign Spare Drives Logical Drive AssignmentsYou can add a spare drive from the list of the unused drives. The spare chosen here is a Local spare and will automatically replace any failed drive in the event of drive failure. The controller will then rebuild data onto the replacement drive Disk Reserved SpaceInitialization Mode Press ESC to continue when all the preferences have been setStripe Size Use the ESC key to view the status of the created logical drive 7.5 Creating a Logical Volume 7.6 Partitioning a Logical Drive/Logical Volume Choose the logical volume you wish to partition, then press ENTER. Choose “Partition logical volume”, then press ENTER. Select from the list of undefined partitions and Press ENTER 7.7 Mapping a Logical Volume to Host LUN 4. When prompted to “Map Host LUN, press ENTER 7.8 Assigning Spare Drive, Rebuild Settings Adding Local Spare Drive7.9 Viewing and Editing Logical Drive and Drive Members Adding a Global Spare DriveFigure 7 - 1 Drive Space Allocated to the Last Partition Deleting a Logical DriveDeleting a Partition of a Logical Drive Assigning a Name to a Logical Drive7-18 Rebuilding a Logical DriveInfortrend Regenerating Logical Drive Parity When rebuild has already started, choose “Rebuild progress” to see the rebuilding progressMedia Scan 2. Iteration Count Write Policy7.10 Viewing and Editing Host LUNs Viewing or Deleting LUN MappingsEdit Host-ID/WWN Name List Pass-through SCSI Commands7.11 Viewing and Editing SCSI Drives Scanning New DriveSlot Number Drive Entry Identifying DriveThese two functions are reserved for Fault Bus configuration Deleting Spare Drive Global / Local Spare DrivePage 7.12 Viewing and Editing SCSI Channels Redefining Channel ModeViewing and Editing SCSI IDs Viewing and Editing SCSI IDs - Host ChannelAdding a SCSI ID Primary/Secondary Controller ID Setting a Primary Controller’s SCSI ID - Drive Channel Deleting an IDSetting a Secondary Controller’s SCSI ID - Drive Channel Setting Channel TerminatorSetting a Transfer Speed Drive ChannelSetting the Transfer Width Host ChannelThis setting is reserved for the Fault-Bus option Viewing and Editing SCSI Target / Drive ChannelSlot Number Maximum Synchronous Transfer Clock Maximum Transfer WidthParity Check Choose “Maximum Sync. Xfer Clock,” then press ENTER. A dialog box will appear on the screen. Enter the clock, then press ENTERData Rate Disconnecting SupportChoose “Disconnect Support.” Choose Yes in the dialog box that follows to confirm the setting Maximum Tag Countshould work fine with most drives. Changing this setting is not recommended unless some particular bus signal issues occur Change Password 7.13 System FunctionsMute Beeper Changing the Password Setting a New PasswordDisabling the Password Reset ControllerThe new password will now become the controller’s password. Providing the correct password is necessary when entering the main menu from the initial screen Shutdown ControllerController Name 7.14 Controller ParametersLCD Title Display Controller Name Restore NVRAM from Disks Saving NVRAM to DisksTerminal Operation 7-38Controller Unique Identifier Password Validation TimeoutPress Yes to confirm Terminal Operation 7-40Set Controller Date and Time Time ZoneDate and Time 7-41SCSI Drive Utilities 7.15 Drive InformationView Drive Information Do not switch the controller’s and/or SCSI disk drive’s power off during the SCSI Drive Low-level Format. If any power failure occurs during the formatting process, the formatting must be performed again when power resumes SCSI Drive Low-level FormatTerminal Operation SCSI Drive Read/Write Test7-44 8.1 Overview Fibre OperationChapter 8.2 Major Concerns Redundant Cache Coherency Channels RCCConnection between Controllers Channel Mode Assignmentperformance Fibre Operation8.3 Supported Features Fibre ChipMultiple Target IDs 1Gbit Fibre ChannelDrive IDs In-band Fibre and S.E.S. SupportChannel Mode 8.4 Configuration Host and Drive ParametersPrimary and Secondary Controller IDs View Channel WWN Redundant Controller Cache Coherency Channel RCC ChannelLimitation View and Edit Fibre Drive View Device Port Name List WWPNUser-Assigned ID Scan SCSI Drive A drive enclosure usually has drive slots pre-assigned with specific IDs. There are occasions when an ID needs to be assigned manually to a device other than an ID provided otherwise. The set slot number and the add drive entry functions are reserved for Infortrends Fault-bus operation View and Edit Host-Side ParametersView Drive Information 1. Fibre Channel Connection Type View and Edit Drive-Side Parameters 2. Drive-Side Dual LoopController Unique Identifier Controller firmware automatically examines the node names and port names of all the connected drives once initiated. If devices on two different drive channels appear with the same loop ID and port name, controller will consider these two drive channels as a dual loopController Communications over Fibre Loops 2. Communications Traffic Distributed over All Drive Loops Select all drive loops and configure them as Drive + RCCOM Drive Loops plus Redundant Controller Communications. The communications traffic between the two controllers will be automatically distributed over all drive loops 8.5 Multi-Host Access Control LUN Filtering Figure 8 - 1 Storage PoolFigure 8 - 2 Host-LUN Mapping Creating LUN MasksFigure 8 - 3 LUN Mask WWN Name List Logical Unit to Host LUN Mapping Choose Yes to proceed LUN Mask ID Range Configuration Filter Type Include or ExcludeAccess Mode Read Only or Read/Write Sample ConfigurationFigure 8 - 4 LUN Filtering - Configuration Sample Configuration Procedure Entry 3 LD1-P0, ID=0x…F111, Mask=0x…FFFE, Filter Type = Include, Access Mode = Read Only. It means P0 of LD1 is Read Only for Host A and B Advanced Configurations 9.1 Fault PreventionS.M.A.R.T Chapter9.1.1 Clone Failing Drive Replace after ClonePerpetual Clone The cloning process will begin with a notification message B. Infortrends Implementations with S.M.A.R.T A. Introduction9.1.2 S.M.A.R.T. Self-Monitoring, Analysis and Reporting Technology Disable Detect OnlyPerpetual Clone Clone + ReplaceEnabling the S.M.A.R.T. Feature Configuration ProcedureExamining Whether Your Drives Support S.M.A.R.T Using S.M.A.R.T. Functions 3b. Whenever a drive predicts symptoms of predictable drive failure, controller will issue an error message 9-10 original role - it will become a spare drive again and start rebuilding the failed drive9.2 Host-side and Drive-side SCSI Parameters 9.2.1 Host-side SCSI ParametersForeword SCSI Channel, SCSI ID and LUN Maximum Concurrent Host LUN Connection “Nexus” in SCSINumber of Tags Reserved for each Host-LUN Connection 9-12Maximum Queued I/O Count LUNs per Host SCSI IDLUN Applicability 9-13What is In-band? Peripheral Device TypeIn-band SCSI or Fibre 9-14Peripheral Device Type Parameters for Various Operating Systems Table 9 - 1 Peripheral Device Type ParametersTable 9 - 2 Peripheral Device Type Settings Cylinder/Head/Sector MappingTable 9 - 3 Cylinder/Head/Sector Mapping under Sun Solaris CapacitySelecting Cylinder Ranges Selecting Sector Ranges Selecting Head RangesConfiguring Sector Ranges/Head Ranges/Cylinder Ranges SCSI Motor Spin-Up 9.2.2 Drive-side Parameters9-18 SCSI Reset at Power-Up SCSI I/O Timeout Disk Access Delay Time9-20 Maximum Tag Count Tag Command Queuing Detection of Drive Hot Swap Followed by Auto Rebuild SAF-TE and S.E.S. Enclosure MonitoringPeriodic Drive Check Time 9-22Idle Drive Failure Detection 9-24 By choosing a time value to enable the Periodic Drive Check Time,” the controller will poll all connected drives through the controller’s drive channels at the assigned interval. Drive removal will be detected even if a host does not attempt to access data on the drive9.3 Monitoring and Safety Mechanisms Dynamic Switch Write-PolicyView Peripheral Device Status 9-25Controller Auto-Shutdown - Event Trigger Option 9-269.4 Disk Array Parameters Rebuild PriorityVerification on Writes 9-2810.1 Operation Theory Redundant ControllerChapter 10.1.1 Setup Flowchart Figure 10 - 1 Redundant Controller Configuration FlowchartFigure 10 - 1 Dual-Controller Using SCSI-Based Controllers 10.1.2 Considerations Related to Physical ConnectionFibre-Based Controllers 1. Dedicated Communications Loops - “RCC” 10.1.3 Grouping Hard Drives and LUN Mapping2. Communications over Drive Loops - “Drive + RCC” Logical Drive, Logical Volume, and Logical Partitions System Drive Mapping Figure 10 - 3 Grouping Hard DrivesFigure 10 - 4 Partitioning of Logical Units Primary and Secondary IDsMapping Figure 10 - 5 Mapping System Drives Mapping LUNsWhat Is a Redundant Controller Configuration? 10.1.4 Fault-ToleranceFigure 10 - 6 Mapping System Drives IDs How does Failover and Failback Work? A. Channel Bus Figure 10 - 7 Redundant Controller Channel BusTable 10 - 1 ID Mapping Status Normal Operation Table 10 - 2 ID Mapping Status Controller FailedFigure 10 - 8 Controller Failover channel 0 - FailedC. Active-to-Active Configuration B. Controller Failover and FailbackReplacing a Failed Unit Auto-FailbackD. Traffic Distribution and Failover Process Figure 10 - 9 Traffic DistributionSymptoms E. Controller FailureFigure 10 - 10 Controller Failover ConnectionOut-of-Band Configuration 10.2 Preparing Controllers10.2.1 Requirements Cabling RequirementsController Settings 1. Enable Redundant Controller2. Controller Unique Identifier 3. Create Primary and Secondary IDs on Drive Channels10.2.2 Limitations 10.2.3 Configurable ParametersPrimary or Secondary Active-to-Active Configuration Active-to-Standby ConfigurationBattery Support Cache Synchronization10-18 Infortrend10.3 Configuration Redundant Configuration Using Automatic Setting 1. Enable Redundant ControllerAutoconfig 10.3.1 Via Front Panel Keypad1. Enable Redundant Controller Redundant Configuration Using Manual Setting2. Controller Unique ID Creating Primary and Secondary ID Starting the Redundant ControllersDrive Channel Assigning a Logical Drive/Logical Volume to the Secondary Controller Host ChannelMapping a Logical Drive/Logical Volume to the Host LUNs What will happen when one of the controllers fails? When and how is the failed controller replaced?The replacement controller has to be pre-configured as the Secondary Front Panel View of Controller Failure10.3.2 Via Terminal Emulation Redundant Configuration Using Automatic SettingRedundant Controller Redundant Configuration Using Manual Setting10-27 10-28 InfortrendCreating Primary and Secondary ID Assigning Logical Drives to the Secondary ControllerDrive Channel Host Channel Choose “host channel-ID” Choose mapping to which “logical unit” Select LUN number Select partition Mapping optioinConfirming mapping scheme Mapping a Logical Drive/Logical Volume to the Host LUNsTerminal Interface View of Controller Failure 10.3.3 When and How Is the Failed Controller Replaced?What will happen when one of the controllers fails? When the scanning has completed, the status will change to Enabled 1. Pulling out one of the controllers to simulate controller failure Forcing Controller Failover for Testing2. Failover by Forcing controller failure RCC Status Redundant Controller Communications Channel Secondary Controller RS-232Remote Redundant Controller Cache Synchronization on Write-Through11.1 View and Edit Logical Drives Record of SettingsChapter 11-2 Partition InformationInfortrend Record of Settings 11.2 View and Edit Logical Volumes11-3 11.3 View and Edit Host LUN’s Access Restriction SettingLUN Mappings Host-ID/WWN Name ListHost Filter Entries AccessLV/LD 11.4 View and Edit SCSI Drives Local Spare?Record of Settings 11.5 View and Edit SCSI Channels11-7 11.6 View and Edit Configuration Parameters Ethernet ConfigurationPPP Configuration Communication ParametersRecord of Settings Caching ParametersHost Side SCSI Parameters Drive Side SCSI ParametersDisk Array Parameters Redundant Controller ParametersCache synchronization on write-through11.7 View and Edit Peripheral Devices Define Peripheral Device Active SignalSet Peripheral Device Entry View System Information11.9 RAID Security Password 11.8 Save NVRAM to Disk, Restore from DiskRAID Security What is it and how does it work? Array Expansion12.1 Overview 12-1Note on Expansion 1. Added Capacity2. Size of the New Drive 3. Applicable ArraysFigure 12 - 1 Logical Drive Expansion Expand Logical Drive Re-Striping12-3 12.2 Mode 1 Expansion Adding Drives to a Logical Drive Add-Drive ProcedureFigure 12 - 2 Expansion by Adding Drive 12-5 Press ESC to proceed and the notification will promptUpon completion, there will appear a confirming notification. The capacity of the added drive will appear as an unused partition Copy and Replace Procedure 12.3 Mode 2 ExpansionCopy and Replace Drives with Drives of Larger Capacity Figure 12 - 3 Expansion by Copy & ReplaceChoose Yes to confirm and proceed Press ESC to view the progress 12.4 Making Use of the Added Capacity Expand Logical Drive 12-9Choose Yes to confirm and proceed Upon completion, you will be prompted by the notification messagePress ESC to return to the previous menu screen The total capacity of logical drive has been expanded to 6 Gigabytes12.5 Expand Logical Volume 12-11Limitations When Using Windows 12.6 Configuration Example Volume Extension in Windows 2000 ServerExample 12-13 You can view information about this drive in the Windows 2000 Server’s Computer Management - Storage - Disk ManagementFollow the steps described in the previous section to add or copy & replace SCSI disk drives and perform Logical Drive Expansion 12-15 Return to Windows 2000 Server’s Disk Management. There now exists a Disk 2 with 8.3GB of free space. You may use the “rescan disks” command to bring up the new driveThe Extend Volume Wizard should guide you through the rest of the process Drive E now has a capacity of about 25GB 12-17Array Expansion Install Select a configuredLCD Keypad Navigation CreateLogical Volume Logical VolumeReset Controller View and EditNavigation Map A-3 View and Edit SCSI DrivesA-4 Infortrend View and EditSCSI Channels Select a Host or Drive ChannelView and Edit Configuration Parameters Navigation Map A-5View and Edit Configuration Parameters Controller Password setRS232 Enabled/Disabled View and Edit Peripheral DeviceSystem Functions View SystemInformation View and EditBasic RAID Management Firmware Functionality SpecificationsAppendix Advanced Features Caching Operation RAID0RAID Expansion Cache buffer sorting prior to cache flush operationFibre Channel Support S.M.A.R.T. Support Redundant ControllerData Safety System Security Environment Management User Interface Remote ManageabilityJBOD-Specific OthersNew Features Supported with Firmware Redundant Controller Rolling Firmware UpgradeSystem Functions Upgrading Firmware Upgrading FirmwareRedundant Controller Firmware Sync-version Upgrading Firmware Using In-band SCSI + RAIDWatch ManagerEstablish the In-band SCSI connection in RAIDWatch Manager Upgrade Both Boot Record and Firmware Binaries Upgrading Firmware Using RS-232C Terminal Emulation Upgrade the Firmware Binary OnlyUpgrading Both Boot Record and Firmware Binaries Establishing the connection for the RS-232C Terminal EmulationUpgrading the Firmware Binary Only InfortrendEvent Messages Event IndexController Event AlertDrive SCSI Channel/Drive Error NotificationDrive ChannelLogical Drive Event General Target EventsAlert SAF-TE Device Controller on-boardI2C Device SES DevicesNotification SAF-TE Device I2C Device InfortrendAlert Controller EventEvent Messages Event Type What to Do?Event Type What to Do?Happens? What to Do? Event TypeHappens? What to Do? Event MessagesDrive SCSI Channel/Drive Error DriveD-10 InfortrendEvent Messages Received Sensekey SensecodeD-11 Sensecode Blocknumber Sensekey SensecodeSensekey Sensecode D-12Event Messages D-13Event Type Event TypeWhat to Do? Event TypeEvent Messages ChannelD-15 D-16 NotificationInfortrend Logical Drive Event AlertEvent Messages D-17D-18 InfortrendEvent Type NotificationEvent Messages D-19D-20 InfortrendEvent Type Happens?Event Messages D-21General Target Events Alert SAF-TE DeviceD-22 InfortrendEvent Messages Controller On-boardD-23 Event Type Event TypeEvent Type D-24Event Messages I2C DeviceD-25 D-26 InfortrendEvent Messages D-27D-28 SES DeviceInfortrend Event Messages 2-Line LCD . Temp Sensor Device Unknown StatusD-29 D-30 InfortrendEvent Messages 2-Line LCD . Current Sensor Device Not SupportedD-31 D-32 InfortrendEvent Messages General Peripheral DeviceD-33 D-34 Notification SAF-TE DeviceInfortrend Event Messages Controller Self DiagnosticsD-35 D-36 I2C DeviceInfortrend Happens? Happens?Happens? Happens?D-38 SES Device AlertInfortrend Event Messages General Peripheral DeviceD-39 Index Index-2 InfortrendIndex-3 Index-4 InfortrendIndex-5 Index-6 InfortrendIndex-7 Index-8 Infortrend