Extron electronic DVS 510 SA f, g, h, i

DVS 510 Series • Installation 9

f RGB/YUV output connectors — Connect cables from RGB (RGBHV, RGBS, RGsB) or

YUVp/HD component (R-Y, Y, B-Y) display devices to these female 15-pin HD connectors

for scaled RGB or component video output. The output can be scaled to 69 different

output rates (see the resolution and refresh rates table on page 27).

NOTE: Outputs are buffered and can be connected simultaneously to two different

displays. The sync and video formats are the same for all outputs.

g DVI-I output connector — Connect a digital (DVI-D) display device to this DVI-I

connector for a scaled DVI output (analog output is not available on this connector). The

figure below shows the pin assignments for the DVI output connector.

8 Not used 16 Hot plug detect 24 TMDS clock–

Pin Signal Pin Signal Pin Signal

1 TMDS data 2– 9 TMDS data 1– 17 TMDS data 0–

2 TMDS data 2+ 10 TMDS data 1+ 18 TMDS data 0+

3 Ground (2/4 ) 11 Ground (1/3) 19 Ground (0/5)

4 Not used 12 Not used 20 Not used

5 Not used 13 Not used 21 Not used

6 DDC clock 14 +5 V power 22 Ground (clock)

7 DDC data 15 Ground (for 5 V) 23 TMDS clock+

18

17 24

9

h Audio input connectors — Connect up to 10 audio input devices to these female

3.5 mm 5-pole captive screw connectors for balanced or unbalanced audio input. (One

audio input is provided for each video input.)

Do not tin the wires!

Balanced Stereo Input

Tip

Ring

Tip

Ring

Sleeves

LR

Unbalanced Stereo Input

Tip

Sleeve

Sleeve

Tip

LR

Figure 4. Audio Input Connector Wiring

i Amplified audio output connector (DVS 510 SA only) — This 4-pole, 5 mm captive

screw connector enables you to connect a set of speakers or another output device to

the DVS 510 SA internal amplifier for amplified output.

All right channel input signals are mixed and summed to produce a single, right channel

output; likewise, all left channel input signals are mixed and summed to produce a

single, left channel output.

If Stereo is selected for the output type, the output is stereo; if Dual Mono is selected,

the right and left channels are mixed and summed for a dual mono output.

With an 8 ohm load, the amplifier produces up to 8 watts per channel. With a 4 ohm

load, the amplifier produces up to 25 watts per channel.

(See “Wiring the Amplified Audio Port [DVS 510 SA Only]”on page 12 for

information on connecting speakers to this port.)

Contents

Main ii Caution Warning Attention Safety Instructions English Consignes de Scurit Franais Sicherheitsanleitungen Deutsch Achtung Vorsicht FCC Class A Notice Conventions Used in this Guide Copyright Trademarks Contents Introduction Installation Operation Remote Conguration and Control Reference Information Introduction About this Guide About the DVS 510 Series Scalers Features Page Controlling the DVS 510 Series DVS 510 Series Introduction 5 Application Diagram Figure 1. Connection Diagram for a DVS 510 SA VCR/DVD TCP/IP The following diagram shows an example of a DVS 510 SA application. Installation Installation Overview Rear Panel a b c d e e f g h i j k l m n o Connecting to the RS-232 Config Port (Front Panel) Wiring the Amplified Audio Port (DVS 510 SA Only) DVS 510 Series Installation 13 Fig 10 Connection examples Dual Mono Connection AMPLIFIED OUTPUTS Operation Front Panel a b c d e f g Powering On Picture-in-Picture (PIP) Mode Enabling PIP Mode Changing the PIP Input Using the PIP Swap Feature Menus on the LCD Screen Menu System Overview Using the menus DVS 510 Series Operation 21 Menu flow diagram Figure 13. Main Menu The following sections describe the submenu options for each of the menus. User Presets Menu Saving or recalling a user preset Input Configuration Menu Selecting an input Configuring an input Available input adjustments Input configuration submenu adjustments Page Output Configuration Menu Resolutions and refresh rates submenu Output Type submenu Sync Polarity submenu Audio Configuration Menu Gain/Attenuation submenu Bass and Treble submenus Limiter submenu (DVS 510 SA only) Audio Delay submenu Advanced Configuration Menu Auto Image submenu Auto Memories submenu Aspect Ratio submenu RGB Delay submenu Switch Effect submenu Test Pattern submenu Internal Temp. screen Reset to Factory screen View Comm Settings Menu Edit Comm Settings Menu DVS 510 Series Operation 35 Next Serial Configuration submenu Set DHCP Mode submenu Set IP Address submenu Set Subnet Mask submenu Set Gateway Addr submenu Picture Controls Adjusting the Picture Controls Picture Controls Summary Input Presets Audio Functions Volume Control Volume LEDs Audio or Video Breakaway Resetting Page Front Panel Lockout (Executive Mode) Additional Features Freeze Power Save Modes Output Sync Mute Using the Optional IR 904 Remote Control Locking IR Remote Control Access Installing Batteries in the IR 904 Remote Control Buttons on the IR 904 Remote Control a b c d e f G J g h i Remote Configuration and Control Serial Ports Ethernet Port Ethernet Cable IP Address Using SIS Commands Scaler-initiated Messages Error Responses Error Numbers Error Response References Using the Command and Response Tables Symbol Definitions for DVS 510 Series SIS Commands X1$ Figure 29. SIS Commands EDID Table X1% X1^ X1& X1* X1( X2) X2# X2$ X2% X2^ X3) Page Command and Response Table for DVS 510 Series SIS Commands Page Page Page Page Page Page Page Page Page Page Page Symbol Definitions for IP-specific SIS Commands Page Page Command and Response Table for IP-Specific SIS Commands Page Page Page Page Page Command ASCII Command Response Stream Files via Telnet, RS-232, or RS-422 E +UF filesize, filename } E +UF filesize*day-of-weekmonthdayyearhourminutesecond, E filename SF }Responds with 4 bytes of le-size plus raw, unprocessed Stream les via Port 80 Back Up and Restore Unit Conguration Page Using the Signal Processing Products Control Program (SPPCP) Installing the Software Installing from the Extron DVD Installing from the Extron website Starting the Software Accessing the Help File Updating the Firmware Using SPPCP Page Page HTML Conguration and Control Accessing the Web Pages Special Characters System Status Page Configuration Pages System Settings Page IP Settings Fields Date/Time Settings section Scaler Settings page Input Configuration section Output Configuration section Advanced Configuration section Page Passwords Page Setting a password Removing passwords Firmware Upgrade page Page File Management Page Uploading Files Adding a Directory Other File Management Activities Control Pages User Control Page Selecting an input and signal type Configuring the audio Picture Control Input Sampling Memory/Input Presets Page User (memory) presets Input presets Page Selecting a PIP input Picture Control (PIP) Input Sampling (PIP) Reference Information Specifications Video input Video processing Video output Sync Audio Audio input Audio output Audio output amplied DVS 510 SA only Control/remote decoder/scaler General Part Numbers Included Parts Optional Accessories Mounting the DVS 510 Scaler Rack Mounting UL guidelines for rack mounting Rack mounting procedure Tabletop Use Button Labels Replacing Button Labels Creating Labels Using the Button Label Generator Page Page IP Addressing What is an IP Address? Choosing IP Addresses Subnet Mask Pinging for the IP Address Pinging to determine the Extron IP address Pinging to determine the web IP address Connecting as a Telnet Client Telnet tips Subnetting, a Primer Gateways Local and remote devices IP addresses and octets Subnet masks and octets Determining whether devices are on the same subnet Extron Warranty Contents