Extron electronic DVS 510 SA manual Audio Commands

Command	ASCII Command	Response	Additional Description
	(Host to Scaler)	(Scaler to Host)
Picture-in-Picture (PIP) (continued)
View PIP input	E PIP }	X! ]	View the input in the PIP window.
Swap	%	Tke ]	Exchange the displayed content between
			the main and PIP windows.
Audio Commands
Audio Volume
Set output volume	X5) V	Vol X5) ]	Set the volume for the output to X5).
Increment volume	+ V	Vol X5) ]	Increase the audio volume.
Decrement volume	– V	Vol X5) ]	Decrease the audio volume.
View volume	V	X5) ]	Show the current volume setting.

Audio Gain and Attenuation (per input)

NOTE: The set gain (G) and set attenuation (g) commands are case sensitive. The increment, decrement, and view

commands are not.

Set audio gain	X5@ G	In X! • Aud X5$ ]
Example	5G	In X! • Aud5 ]
Set attenuation	X5# g	In X! • Aud X5$ ]
Example	15g	In X! • Aud –15 ]
Increment level	+ G	In X! • Aud X5$ ]
Decrement level	– G	In X! • Aud X5$ ]
View	G	X5$ ]

Set audio gain level to X5@ dB. Set the audio gain to 5 dB. Set attenuation to X5# dB.

Set the audio attenuation to -15 dB. Increase the audio level by 1 dB. Decrease the audio level by 1 dB. View the current audio level.

Audio Bass (global)
Set the bass level	X5% <	Bas X5% ]	Set the global bass level to X5%.
Example	10 <	Bas 010 ]	Set the bass level to +3 dB.
Increment bass	+ <	Bas X5% ]	Increase the bass level.
Decrement bass	– <	Bas X5% ]	Decrease the bass level.
View bass level	<	X5% ]	Show the current bass level.
Audio Treble (global)
Set the treble level	X5% >	Trb X5% ]	Set the global treble level to X5%.
Increment treble	+ >	Trb X5% ]	Increase the treble level.
Decrement treble	– >	Trb X5% ]	Decrease the treble level.
View treble level	>	X5% ]	Show the current treble level.

Power Amp Limiter (DVS 510 SA only)

Enable	E 1 APWR }	Apwr 1 ]	Enable the power amp limiter to detect
			and eliminate clipping distortion.
Disable	E 0 APWR }	Apwr 0 ]	Disable the power amp limiter.
View setting	E APWR }	X1) ]	Show current power amp limiter setting.

NOTE: X!	= PIP input selection	1 through 10
X1)	= Limiter on and off	0 = off, 1 = on
X5)	= Audio volume level	0 through 100
X5@ = Audio gain level		0 through 12 dB (dependent of resolutions)
X5# = Audio attenuation level		0 through 12 dB (decibels below 0)
X5$ = Audio gain or attenuation (unit response)		-12dB through +12 dB (can be positive or negative)
X5%	= Audio bass and treble	0 through 16 (-12 dB through +12 dB) in increments of 1.5 dB:
		0 = -12 dB, 8 = 0 dB (default), 16 = 12 dB

DVS 510 Series • Remote Configuration and Control 61