Output Configuration Menu | Extron electronic DVS 510 SA specification

Output Configuration Menu

The output configuration menu allows you to set output resolution and refresh rate, output signal type, and sync polarity (RGBHV only). The following flow diagram shows the output configuration submenus and the adjustments that can be made from them.

Input

Configuration

Menu

Output

Configuration

Next

Resol	1024	x 768
Refresh	@	60 Hz

Next			Output Type
Next				RGBHV
				RGBHV

Next

Sync Polarity

H –			V –

			Resolution	Refresh Rate
			Select the output resolution
			and refresh rate.
	Next		and refresh rate.
	Next		See the table on the next page
			for available combinations of
			resolutions and refresh rates.
			Default: 1024 x 768 @ 60 Hz

Video signal types

Select the output signal format:

•RGBHV (default)

•RGBS

•RGsB

•YUV Bi-level (EDTV standard)

•YUV Tri-level (HDTV standard)

		Polarity combinations
	Select the sync polarity
	combination:
	combination:			Next
	•	H –	V – (default)	Next
	•	H –	V – (default)
	•	H –	V +
	•	H +	V –
	•	H +	V +

•N/A*

*Appears when a signal type other than RGBHV is selected.

Figure 16. Output Configuration Menu

Resolutions and refresh rates submenu

While the Output Configuration menu is displayed, rotate the horizontal Adjust ([) knob to select the output resolution and the vertical Adjust ({) knob to select the refresh rate. The default resolution and rate for the DVS 510 Series are 1024x768 @ 60 Hz.

The table on the next page shows the available resolutions and refresh rates on the DVS 510 Series.

DVS 510 Series • Operation 26

Image 32

Extron electronic DVS 510 SA manual Output Configuration Menu, Resolutions and refresh rates submenu

Contents

DVS 510 Series Safety Instructions English FCC Class a Notice Extron Electronics. All rights reserved Conventions Used in this GuideVariables are written in slanted form as shown here Contents Creating Labels Using the Button Label Generator 113 102104 107 About this Guide About the DVS 510 Series Scalers Features DVS 510 Series Introduction Controlling the DVS 510 Series Rack-mountable 2U, full rack width metal enclosure Application Diagram Connection Diagram for a DVS 510 SA Installation Installation Overview Rear Panel Video inputs 5 and 6 buffered RGB or YUV component Connect DVIIM-VGAF/DVIIF DVI and Analog Breakout Cable Unbalanced Stereo Input Audio Output Connector Wiring Connecting to the RS-232 Config Port Front Panel Pin Assignments for the RS-232 Port Speaker system. See on the next page for examples Wiring the Amplified Audio Port DVS 510 SA OnlyRed Black Positive + Negative Speaker Connection Examples Front Panel DVS 510 and DVS 510 SA Front Panel 2 Composite 4 S-video 10 DVI DVS 510 Series Operation Powering On Power-up and Default Cycle Picture-in-Picture PIP Mode Audio and video breakaway are not allowed Changing the PIP Input Enabling PIP ModeUsing the PIP Swap Feature Menu System Overview Using the menusMenus on the LCD Screen Menu flow diagram Cycle User Presets Menu Saving or recalling a user preset Input Configuration Menu InputComposite Video Configuring an input Available input adjustmentsInput configuration submenu adjustments Selecting an input Film Mode Detect Pixel Phase Inputs 5, 6, 7,Vertical Start Position Horizontal Start Position Output Configuration Menu Resolutions and refresh rates submenu Output Type submenu Sync Polarity submenu Audio Configuration Menu Gain/Attenuation submenuBass and Treble submenus Limiter submenu DVS 510 SA only Audio Output submenu Advanced Configuration MenuAudio Delay submenu Auto Image submenu Auto Memories submenu Auto Memories and Auto-Image Interaction RGB Delay submenuAspect Ratio submenu Test Pattern submenu Switch Effect submenuOff default To select a test pattern Reset to Factory screenInternal Temp. screen View Comm Settings Menu Edit Comm Settings Menu Serial Configuration submenu Set Dhcp Mode submenu Picture Controls Exiting the Menu SystemSet IP Address submenu Set Subnet Mask submenu Adjusting the Picture Controls Picture Controls Summary Function Fixed Output Variable Output Amplified Output Input PresetsAudio Functions Volume Control Volume LEDsVolume Knob Rotations Volume Level Steps 100 Resetting Audio or Video Breakaway Default firmware for a single Mode 3 turns events on or off. IfMode 4 does the following Mode 5 performs a complete Front Panel Lockout Executive Mode Additional FeaturesPower Save Modes Freeze Output Sync Mute Using the Optional IR 904 Remote ControlOverscan Mode Buttons on the IR 904 Remote Control Locking IR Remote Control AccessInstalling Batteries in the IR 904 Remote Control Pan Button Function Adjust Button SizeZoom IR 904 Image Adjustment Buttons Ethernet Cable Serial PortsEthernet Port Using SIS Commands Establishing an Ethernet Connection Using TCPConnection Timeouts IP Address Scaler-initiated Messages Error ResponsesError Numbers Telnet Web browser Error Response ReferencesUsing the Command and Response Tables X1! = Symbol Definitions for DVS 510 Series SIS CommandsX1 = SIS Commands Edid Table X1$ X4$ X2#X2$ X5# X5$ Command and Response Table for DVS 510 Series SIS Commands Input Video FormatInput Edid Inputs 5, 6, 8, and 10 only DVI and VGA Auto-Image Vertical Start Picture Controls Film Mode Detect 32 pulldown detectionVideo Mute Horizontal Size Horizontal Shift CenterVertical Shift Center Output Scaler Rate Power Save / Screen Saver X2$ OsynX2# Opol Picture-in-Picture PIP Audio Commands Presets X5 AlmtX5! Afmt X5& Aflw Advanced Configuration X2 , X1$ NP Nmp X2 , X1$X2 Test X3& Vdly # * X3* Oscn Oscn X# # Oscn Oscn X# X1@ X4%Information Request Erase flash memory24 X8# X8$ Symbol Definitions for IP-specific SIS CommandsX7# X9# X10 =X10! = X10# = X10% = X10& = Bidirectional Serial Port Command and Response Table for IP-Specific SIS CommandsCommand Ascii Command Response Additional Description IP Setup Commands Ethernet Data Port X10# CX Ipx X10# X10#X8$ CI Ipi X8$ Iph Password and Security Settings X10@ CU Ipu Remap Port Destinations File Commands Directories Stream files via Port Back Up and Restore Unit ConfigurationStream Files via Telnet, RS-232, or RS-422 Event Control Installing from the Extron DVD Using the Signal Processing Products Control Program SppcpInstalling the Software Installing from the Extron website Download Center screen on the Extron Website Starting the Software Tabs on the Sppcp Select Connection Type Window Accessing the Help File Signal Processing Products Control Program Main Window Updating the Firmware Using Sppcp Firmware Loader Window Choose Firmware File Window Firmware Upload in Progress Accessing the Web Pages Proxy server... check box, then click OK Special Characters + ~ , @ = ` ’ ‘ \ ? and space System Status System Status Configuration Pages System Settings IP Settings Fields + ~ , @ = ’ ‘ \ and ? Date/Time Settings section Date/Time Settings Fields Scaler Settings Input Configuration section Output Configuration section Advanced Configuration section Test Patterns on the DVS Removing passwords PasswordsSetting a password Firmware Upgrade Firmware Upgrade Choose File to Upload Window with a Firmware File Selected + ~ , @ = ` ’ ‘ \ and space File ManagementUploading Files Other File Management Activities Control PagesAdding a Directory Selecting an input and signal type User Control Configuring the audio Picture Control Input Sampling Memory/Input Presets User memory presets To recall a saved input preset Input presetsTo create an input preset PIP Setup PIP Setup Selecting a PIP input Picture Control PIP Input Sampling PIP Video processing SpecificationsVideo input Video output SyncAudio Audio input Audio output Audio output amplified DVS 510 SA onlyControl/remote decoder/scaler General Optional Accessories Part NumbersIncluded Parts Description Part Number Rack mounting procedure Mounting the DVS 510 ScalerRack Mounting UL guidelines for rack mounting Replacing Button Labels Button LabelsTabletop Use Creating Labels Using the Button Label Generator Replacing a Button Label Button Label Generator Window Example Blank Button Labels What is an IP Address? IP AddressingChoosing IP Addresses Class Name Valid Address Range Identifier Arrangement Click OK. a command window opens Subnet MaskPinging for the IP Address Pinging to determine the Extron IP address Connecting as a Telnet Client Pinging to determine the web IP address Telnet tips Telnet Screen Subnetting, a Primer Gateways Local and remote devices IP addresses and octetsSubnet masks and octets Determining whether devices are on the same subnet USA, Canada, South America Japan Central America Europe, Africa, and the Middle China EastAsia Middle East Europe