Manuals / Brands / Computer Equipment / Switch / Extron electronic / Computer Equipment / Switch

Extron electronic DVS 510 SA Command and Response Table for DVS 510 Series SIS Commands

1 128

Download 128 pages, 8.84 Mb

DVS 510 Series • Remote Configuration and Control 55

Command ASCII Command

(Host to Scaler)

Response

(Scaler to Host) Additional Description

Input Selection

Video and audio X! ! In X! • All ]Select video and audio from input source

X!.

Video X! & In X! • RGB ]Select video from input source X!.

Audio X! $ In X! • Aud ]Select audio from input source X!.

NOTES: • When the DVS is in PIP mode, the input selection command affects the PIP window. In addition, all picture

controls and advanced input settings apply to the PIP input.

• Query commands (!, &, and $) return the full tagged response as seen in verbose modes 2 and 3. However,

responses that include only the X! variable are returned in verbose mode 0 or 1 (not tagged).

Input Video Format

Set video format X! * X# \ Typ X! * X# ]Set input X! to video format X#.

View video format X! \X# ]View video type of input X!.

Input EDID (Inputs 5, 6, 8, and 10 only — DVI and VGA)

Specify an EDID value E A X! * X2! EDID }Edid A X! * X2! ]Set the EDID resolution and refresh rate

for input X! to X2!.

View EDID data E A X! EDID } X2! ]

In verbose mode:

Edid A X! * X2! ]

View the EDID setting for input X!.

Auto-Image

Enable Auto-Image X! * 1 A Img X! * 1 ]Perform Auto-Image on input X! when

it is selected or when a new signal is

applied.

Disable Auto-Image X! * 0 A Img X! * 0 ]Turn off Auto-Image for input X!.

View Auto-Image X! AX! ]View the current Auto-Image setting for

input X!.

Execute an Auto-Image AImg ]Perform an Auto-Image for the current

input.

Execute and ll 1 * AImg 1 ]Perform an Auto-Image on the current

input and ﬁll the entire output display.

Execute and follow 2 * AImg 2 ]Perform an Auto-Image on the current

output and follow the aspect ratio of the

input.

NOTE: X! = Input selection 1 through 10

X# = Input video format 1 = RGB, 2 = YUVp/HDTV, 3 = RGBcvS, 4 = YUVi, 5 = S-video,

6 = Composite video, 7 = DVI

X2! = EDID resolution and refresh rate See the EDID resolution table on page 53 for the available values.

Command and Response Table for DVS 510 Series SIS Commands

Contents

Main ii Caution Warning Attention Safety Instructions English Consignes de Scurit Franais Sicherheitsanleitungen Deutsch Achtung Vorsicht FCC Class A Notice Conventions Used in this Guide Copyright Trademarks Contents Introduction Installation Operation Remote Conguration and Control Reference Information Introduction About this Guide About the DVS 510 Series Scalers Features Page Controlling the DVS 510 Series DVS 510 Series Introduction 5 Application Diagram Figure 1. Connection Diagram for a DVS 510 SA VCR/DVD TCP/IP The following diagram shows an example of a DVS 510 SA application. Installation Installation Overview Rear Panel a b c d e e f g h i j k l m n o Connecting to the RS-232 Config Port (Front Panel) Wiring the Amplified Audio Port (DVS 510 SA Only) DVS 510 Series Installation 13 Fig 10 Connection examples Dual Mono Connection AMPLIFIED OUTPUTS Operation Front Panel a b c d e f g Powering On Picture-in-Picture (PIP) Mode Enabling PIP Mode Changing the PIP Input Using the PIP Swap Feature Menus on the LCD Screen Menu System Overview Using the menus DVS 510 Series Operation 21 Menu flow diagram Figure 13. Main Menu The following sections describe the submenu options for each of the menus. User Presets Menu Saving or recalling a user preset Input Configuration Menu Selecting an input Configuring an input Available input adjustments Input configuration submenu adjustments Page Output Configuration Menu Resolutions and refresh rates submenu Output Type submenu Sync Polarity submenu Audio Configuration Menu Gain/Attenuation submenu Bass and Treble submenus Limiter submenu (DVS 510 SA only) Audio Delay submenu Advanced Configuration Menu Auto Image submenu Auto Memories submenu Aspect Ratio submenu RGB Delay submenu Switch Effect submenu Test Pattern submenu Internal Temp. screen Reset to Factory screen View Comm Settings Menu Edit Comm Settings Menu DVS 510 Series Operation 35 Next Serial Configuration submenu Set DHCP Mode submenu Set IP Address submenu Set Subnet Mask submenu Set Gateway Addr submenu Picture Controls Adjusting the Picture Controls Picture Controls Summary Input Presets Audio Functions Volume Control Volume LEDs Audio or Video Breakaway Resetting Page Front Panel Lockout (Executive Mode) Additional Features Freeze Power Save Modes Output Sync Mute Using the Optional IR 904 Remote Control Locking IR Remote Control Access Installing Batteries in the IR 904 Remote Control Buttons on the IR 904 Remote Control a b c d e f G J g h i Remote Configuration and Control Serial Ports Ethernet Port Ethernet Cable IP Address Using SIS Commands Scaler-initiated Messages Error Responses Error Numbers Error Response References Using the Command and Response Tables Symbol Definitions for DVS 510 Series SIS Commands X1$ Figure 29. SIS Commands EDID Table X1% X1^ X1& X1* X1( X2) X2# X2$ X2% X2^ X3) Page Command and Response Table for DVS 510 Series SIS Commands Page Page Page Page Page Page Page Page Page Page Page Symbol Definitions for IP-specific SIS Commands Page Page Command and Response Table for IP-Specific SIS Commands Page Page Page Page Page Command ASCII Command Response Stream Files via Telnet, RS-232, or RS-422 E +UF filesize, filename } E +UF filesize*day-of-weekmonthdayyearhourminutesecond, E filename SF }Responds with 4 bytes of le-size plus raw, unprocessed Stream les via Port 80 Back Up and Restore Unit Conguration Page Using the Signal Processing Products Control Program (SPPCP) Installing the Software Installing from the Extron DVD Installing from the Extron website Starting the Software Accessing the Help File Updating the Firmware Using SPPCP Page Page HTML Conguration and Control Accessing the Web Pages Special Characters System Status Page Configuration Pages System Settings Page IP Settings Fields Date/Time Settings section Scaler Settings page Input Configuration section Output Configuration section Advanced Configuration section Page Passwords Page Setting a password Removing passwords Firmware Upgrade page Page File Management Page Uploading Files Adding a Directory Other File Management Activities Control Pages User Control Page Selecting an input and signal type Configuring the audio Picture Control Input Sampling Memory/Input Presets Page User (memory) presets Input presets Page Selecting a PIP input Picture Control (PIP) Input Sampling (PIP) Reference Information Specifications Video input Video processing Video output Sync Audio Audio input Audio output Audio output amplied DVS 510 SA only Control/remote decoder/scaler General Part Numbers Included Parts Optional Accessories Mounting the DVS 510 Scaler Rack Mounting UL guidelines for rack mounting Rack mounting procedure Tabletop Use Button Labels Replacing Button Labels Creating Labels Using the Button Label Generator Page Page IP Addressing What is an IP Address? Choosing IP Addresses Subnet Mask Pinging for the IP Address Pinging to determine the Extron IP address Pinging to determine the web IP address Connecting as a Telnet Client Telnet tips Subnetting, a Primer Gateways Local and remote devices IP addresses and octets Subnet masks and octets Determining whether devices are on the same subnet Extron Warranty Contents