X2$ Osyn, X2# Opol, Pip | Extron electronic DVS 510 SA instruction

Command	ASCII Command	Response	Additional Description
Command	(Host to Scaler)	(Scaler to Host)	Additional Description
	(Host to Scaler)	(Scaler to Host)


Output Sync Format and Polarity
Set sync format	E X2$ OSYN }	Osyn X2$ ]	Set the sync format for the VGA output
			to X2$.

NOTE: Setting the sync format to YUV bi-level and tri-level also affects the colorspace of the DVI output.

View sync format	E OSYN }	X2$ ]	View the current output sync format.
Set polarity	E X2# OPOL }	Opol X2# ]	Set the sync polarity for the VGA output
			to X2#.
View polarity	E OPOL }	X2# ]	View the output video and sync polarity.

Power Save / Screen Saver

NOTE: The action initiated by these commands takes place when there is no active video on the selected input.

Video mute	E 0 PSAV }	Psav 0 ]	Mute the video output and retain the
			output sync (default). The screen is black.
Blue output	E 1 PSAV }	Psav 1 ]	Set the video output to blue.
Blue output and	E 2 PSAV }	Psav 2 ]	Set the video output to blue for 1 minute,
timeout			then mute the output video and sync.
View setting	E PSAV }	X4) ]	View the current power save mode.

Picture-in-Picture (PIP)
PIP on	E X! PIP }	Pip X! ]	Enable picture-in-picture with input X! as
			the PIP input.

NOTES: • When PIP is enabled, all picture control commands apply only to the image in the PIP window.

• If input X! is in the same high or low resolution category as the currently displayed input, the error code E13 (invalid parameter) is returned. The table below shows the categories for each input.

Input	High Resolution	Low Resolution

1		Composite

2		Composite

3		S-video

4		S-video

5	RGB, YUVp/HDTV	YUVi, RGBcvS

6	RGB, YUVp/HDTV	YUVi, RGBcvS

7	RGB, YUVp/HDTV	YUVi, RGBcvS

8	DVI (all formats)

9	RGB, YUVp/HDTV	YUVi, RGBcvS

10	DVI (all formats)

PIP off	E 0 PIP }		Pip 0 ]	Disable PIP.
NOTE:	X! = Input selection for PIP	1 through 10
	X2# = Output polarity	0	= H-/V- (default), 1 = H-/V+, 2 = H+/V-, 3 = H+/V+
	X2$ = Output sync format	0	= RGBHV (default), 1 = RGBS, 2 = RGsB, 3 = YUV bi-level,
	X4) = Power save and screen saver modes	4	= YUV tri-level
	X4) = Power save and screen saver modes	0	= Black screen; output sync retained
		1	= Blue screen; continuous sync
		2	= Timed blue screen. Screen is blue for 1 minute, then output video
			and sync are muted.

DVS 510 Series • Remote Configuration and Control 60

Extron electronic DVS 510 SA manual X2$ Osyn, X2# Opol, Power Save / Screen Saver, Pip

Models: DVS 510 SA

E X2$ OSYN }

X2$ ]

E X2# OPOL }

X2# ]

Power Save / Screen Saver

Picture-in-Picture (PIP)

E X! PIP }